Incoming Power Problem Parts

Washing machine should have been an easy fix that I had done before but ran into problems with the upper bearing and the bearing diameter on the shaft (a no go situation). By the time I was able to get the bearing seated I had damaged the new bearing. Much to my surprise Cierra in customer service sent me out a new bearing kit. I was then able to get the washer up and running with the new bearing kit and motor stator replacement. The dryer was a matter of replacing all of the electrical... Read more

Put both thermostats in as I did not know if the unit was cycling on high limit at times. Fixed both issues plus I used my lawn blower and blew all the lint out of dryer and short 3' hose. I also lubed rear drum bearings. Works like new. Ron R Read more

I checked the continuity on the thermal fuse (which was blown) and knew that it needed to be replaced. This made me question why it blew (i.e. what caused it to fail). I checked continuity on the thermostat (high limit) as well as the thermostat for the element. Both passed a continuity test, so I removed the high limit thermostat to inspect it and could hear it rattling inside. This leads me to believe the spring inside had failed, so I replaced this thermostat as well. Put it back... Read more

Replaced 3 low cost parts as advised by Appliance Parts Pros. Saved the labor costs by troubleshooting and replacing parts with their great videos. Works like new, and took 15 minutes to complete the repair. Read more

After reviewing various posts on the internet, I tested the high heat temperature limiter and determined it was faulty due to lint buildup. Ordered the parts from AppliancePartsPros.com on Friday afternoon and parts were delivered on Saturday afternoon. Replaced the parts- dryer works as good as new. Read more

I have a Bosch nexxt 500 series dryer that stopped heating. It was still running fine, just no heat. I did some research and found the Limiter as the possible problem. I pushed the red reset button. The dryer started heating up, but with in 1 cycle kicked off again. I called A.P.P. and spoke to Cecilia. She was very helpful. After a brief description of my situation she recommended just to replace the Limiter. I did so and that fixed the problem. Very simple replacement. It look longer to take... Read more

I replaced the thermal cut-off sensors and the cutoff-Tml Read more

When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

• Too hot

Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been... Read more

Ordered a new safety thermostat. Installed it in 10 minutes and good as new. Thanks for your great trouble shooting and fast parts the repair was a breeze. Read more

• Takes too long to dry

Replaced timer and cycling thermostat. cycling thermostat was the problem. For some reason it wasn't getting the message to the timer needed to cycle the dial. Read more