Thermal Fuse Parts

• Doesn't shut off

Looked online. Others said to start with the thermostat because its cheap and easy to fix, so I did. The thermostat is located at the rear of the oven on the back. You need to remove a total of 3 panels to get to it. Do not confuse it with the thermal sensor at the rear of the oven on top. My thermostat was clearly deformed, and I had never run a self clean like other with testify to. Simply replace it - easy. Oven worked like new. Read more

Checked vent first to see if there was a blockage. Removed top, front and drum of dryer. Replaced all sensors including flame detection and gas valve coils. Re-assembled and tested. Dryer was now heating Read more

I was having trouble with my Kenmore Front Load washer. It wouldn't finish the wash cycle...it kept displaying an LE Error code. After I went to Google to help diagnose the problem, which was a bad RPS Sensor, I ordered the part from AppliancePartsPros.com. It literally took about 15-20 mins and with the help of my son-in-law, my washing machine was fixed!! It was going to cost me $85.00 for the Sears repairman to walk in my door, not including parts and labor, and I only paid $27.00... Read more

Replaced fuse. It took much longer to get the oven out of the wall to access the fuse and replace the front panel than to do the repair. This fuse failed at the end of the cleaning cycle for the bottom oven and left the door locked because the open fuse removed the 120v power from the control board. The locked door made it impossible to remove one of the screws holding the wall oven in place. However, after I ground off the head of the screw behind the edge of the locked door I was able to... Read more

So I replaced the hi-temp thermostat and the problem is fixed. Read more

Used video and took apart dru, this was extremely helpful. I bypassed the belt and door switch. Tested gas valves (gas disconnected) with multimeter. Found that the igniter worked the first gas valve, but the second gas valve would not open and the igniter would stay on. Found a flow chart online that shows the flame detect turns on causing the gas to turn on and shuts off the igniter. I replaced it and tested again. Igniter turns on, shuts off, then power to the second gas valve turns... Read more

Viewed the video before I purchased the part. Received the part and put it in. Everything went as planned. Read more

Tried to turn the microwave on, checked the outlet for power, check the breaker to see if it was tripped, all was in order. Removed the over the range microwave and pull the covers, Tested continuity with a multimeter for each of the 4 normally closed thermostats, found 2 bad (open). The upper 110 and the lower right 70. Ordered the needed parts as well as both lamp sockets and bulbs as they where broken too. The parts where correct and where delivered on time. (Also, in your tools needed or... Read more

Realizing that there could be multiple reasons for a gas dryer failing to heat, I decided to test everything I could. The very detailed and product specific video showed me how to disassemble the dryer. The thermostat, cycling thermostat, high limit, flame detector, igniter, gas valve coils and timer all showed correct continuity or resistance. I thought it might be the gas valve itself, but felt that wasn't likely so I decided to go ahead and replace the thermostats and limit switch since... Read more

Removed the heater of course and installed the part. Very easy to do no need to remove the drum, just top cover, control panel, and front door assembly. Remove the one screw holding heater, remove blue wire, turn heater CCW to the 8 o'clock poisiton. Install in the reverse order. This is the secound one in a month if it fails again i'll just bypass it and install a 25 AMP fuse. Read more

• Too hot

I removed the front panel and observed the heating element while running the dryer. It was cycling off every minute or so and staying off for several minutes. Even though it was likely the high temp cycling thermostat I replaced both the 14, and 15 cycling thermostats which I think are the original factory units. That makes them nearly 35 years old. Problem fixed. Read more

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

Ohmed the oven heat elements and oven sensor, they checked out fine. No broken or bad connections. Figured it had to be high limit switch opening or control panel. With Christmas meal around corner I ordered both. Oven working fine and my wife is happy. Read more

I contacted Appliance Parts Pros, and told them what the problem was and what it was doing. They sent me an email with the parts number needed to complete the repair. This was a built in a cabinet unit and I required help removing it and reinstalling it. The repair was relative easy once I had the parts and it took approximately four hours,. It took longer getting to the defective parts than replacing them. ... Read more

• Shuts off too soon

Replaced heating element about three months ago. Had to order thermistor because of error code "ts" on display and dryer would not run. Removed the two screws on the back that holds the top in place. After removing the top, remove the screws that hold the control panel on front. Make sure not to break the tabs that help hold it in place You do not have to unplug any connectors for the control panel. Lay control panel across top of dryer carefully so that it will be out of the way. Next... Read more