Power Strike Small Engine Spark Plug Parts
Genuine Ge part
By: Ge
Part Number: WD13X10003
If your dishwasher won't start or the door won't lock, the door latch assembly is likely failed. DIY-friendly repair takes about 30 minutes to replace.
This part fixes the following symptoms
-
Won't start
-
Door latch failure
-
Door won't close
See more...
Do-It-Yourself Stories from Customers like You
My ge performance plus dishwasher quit working the control panel would not light up and allow me to choose a cyle to run Jeff J. • Lex , KY • March 11, 2015
With the power to the dishwasher on, I removed the six or seven screws holding the door panel together. With the door separated, I manually moved the switch which should close when the dishwasher latch closes. This illuminated and activated the control panel telling me that the problem was in the door latch. I purchased a new latch from appliance parts pros and installed it. Very easy fix for a homeowner, taking thirty minutes.
Read more
More
$38.44
- Compare At:
-
$45.36
- You Save:
-
$6.92
Genuine Bosch part
By: Bosch
Part Number: 00166621
Fix a detergent dispenser door that won't stay closed or pops open during the wash cycle. This lid replacement is a simple DIY repair with no tools needed.
Do-It-Yourself Stories from Customers like You
Soap dispenser did not stay closed Petra G. • West Chester , PA • October 18, 2014
After having seen the video I installed the new lid and it worked.
Read more
More
$54.68
- Compare At:
-
$65.07
- You Save:
-
$10.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10455271
Fix water leaking from the bottom or poor cleaning in lower rack. This dishwasher diverter cover protects internal valve components. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Leaked water onto diverter motor(bottom center) Mark D. • Milan , NH • November 23, 2019
Replaced sump because the seal is not sold separately. You will need a skinny clamp after cutting the original swaged clamp off. Also Had to replace the cover as its seal is not sold separately either. Used dish soap on seals during assembly.
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Ge part
By: Ge
Part Number: WD09X21321
Fix a cracked or broken dishwasher handle that won't open properly. Requires removing front panel with torx and hex screws. Video guide available.
Do-It-Yourself Stories from Customers like You
Dishwasher needed new handle and console cover. Steven S. • Wheaton , IL • October 26, 2020
Reviewed repair via youtube. Disconnected the dishwasher power and water. Removed dishwasher from under the cabinet. Removed and disassembled the door and then made the repair. The last step reinstalled the door and dishwasher.
Read more
More
$83.95
- Compare At:
-
$99.90
- You Save:
-
$15.95
Genuine Whirlpool part
By: Whirlpool
Part Number: WP691581
The Door Switch Lever is an OEM part for Whirlpool dryers. It plays a vital role in ensuring the dryer only operates when the door is securely closed by engaging with the door switch to signal the door's status.
Causes of a bad door switch lever can include normal wear and tear from repeated use, physical damage from accidental impact, or deformation from heat and humidity inside the dryer. A faulty lever can prevent the dryer from starting or stopping correctly.
Symptoms of a bad door switch lever include:
- Dryer not starting
- Dryer stopping mid-cycle
- Door not latching properly
- The dryer continuing to run with the door open
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Won't start
-
Doesn't shut off
See more...
Do-It-Yourself Stories from Customers like You
The lever to the door switch broke. Valerie M. • Rochester , NH • April 02, 2014
First, I rooked on YouTube for a video on how to fix it. The video brought me to a very helpful video with a link to your website. We have had this dryer since we bought the house 10 years ago and the thought of buying something new, that wasn't made as well was a dreaded thought. I went on the website, entered the model number of my dryer and then a search link for a parts search. Not knowing the part number, I was able to find the exact thing I needed. It was amazing and so easy! Had...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3391914
Dryer won't heat or overheats? The high limit thermostat monitors drum temperature. Moderate DIY repair with heater housing access required.
Do-It-Yourself Stories from Customers like You
My whirlpool dryer was not getting hot Anthony D. • Sanibel , FL • May 01, 2016
I purchased a new heating element. Very easy to fix in about twenty minutes
Read more
More
$81.36
- Compare At:
-
$96.82
- You Save:
-
$15.46
Genuine Whirlpool part
By: Whirlpool
Part Number: 676413
Fix a detergent dispenser that won't open or close properly with this latch kit. Includes all components for secure closure. 10-15 minute repair.
Do-It-Yourself Stories from Customers like You
Latch would not open consistently on detergent dispenser James G. • Waxhaw , NC • January 12, 2015
Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Ge part
By: Ge
Part Number: WD12X10284
The Fill Cap Assembly is an OEM part for GE dishwashers. This assembly includes the cap that covers the opening where rinse aid or other additives are poured into the dishwasher. It ensures that the additives are securely contained and properly dispensed during the wash cycles, contributing to effective cleaning and drying.
Over time, the fill cap assembly can become damaged due to regular use, exposure to cleaning agents, or accidental mishandling. A compromised fill cap can lead to leaks or improper dispensing of rinse aid, affecting the dishwasher's performance.
Symptoms of a bad fill cap assembly include:
- Rinse aid or additives leaking from the dispenser
- The cap not securing properly or coming off easily
- Improper dispensing of rinse aid
- Visible cracks or damage to the cap
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Will not dispense detergent
See more...
Do-It-Yourself Stories from Customers like You
1 not draining properly 2 not cleaning properly 3 not filling properly 4 not running properly 5 sump and sump cap was filthy 6 James W. • San Diego , CA • March 19, 2017
1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve.
Parts $220 for Dishwasher
Estimated Labor $400.00
Labor $0.00
Parts $100.00 for Pullout Faucet
Estimated Labor $175.00
Labor $0.00
Read more
More
$24.95
- Compare At:
-
$29.69
- You Save:
-
$4.74
Genuine Samsung part
By: Samsung
Part Number: DC47-00017A
Dryer won't heat or stops heating mid-cycle? The high limit thermostat cuts power when temperatures spike. Easy 15-minute fix with video guide.
Do-It-Yourself Stories from Customers like You
My dryer would not heat up Chris R. • Glen Saint Mary , FL • January 07, 2015
When starting my dryer the motor would power up and rotoe the drum and blower. Afetr about 20-30 seconds the igniter would come on then the gas valve would open and I would get heat for about 6 or 7 seconds then it would shut off. I know the burner is suppoed to cycle on and off but once the burner shut off it would not come bqack on unless I shut the dryer off and then back on. I checked for continuity on the thermistor, the thermal fuse and the high temp sensor. All three of them appeared to...
Read more
More
$82.47
- Compare At:
-
$97.31
- You Save:
-
$14.84
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10467289
The Water Temperature Sensor is an OEM part for Whirlpool washing machines. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle. Note: The sensor does not include the seal W11590578. Order separately if needed.
Causes of a bad temperature sensor can be failures over time due to mechanical wear, thermal stress on electronic components, or damage from leaks/flooding inside the unit.
Symptoms of a bad water temperature sensor include:
- Inability to switch between wash steps or advance through the cycle
- Erratic or inconsistent temperature readings
- Failure alarms or error codes displayed
- Improper or incomplete washing even on high heat settings
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
F2 e3 error code on front load duet washer Mark M. • Saratoga Springs , NY • September 16, 2016
Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since.
Read more
More
$34.75
- Compare At:
-
$41.00
- You Save:
-
$6.25
Genuine Frigidaire part
By: Frigidaire
Part Number: 154574401
Dispenser door won't close or latch? Replace the detergent dispenser assembly. DIY repair takes 5-10 minutes with video guide. Fixes stuck or broken latch.
This part fixes the following symptoms
-
Will not dispense detergent
See more...
Do-It-Yourself Stories from Customers like You
Dishwasher soap dispenser door would not open during cycle Brian L. • Hammonton , NJ • January 11, 2015
I bought a replacement part and changed it out.
Read more
More
$70.31
- Compare At:
-
$83.67
- You Save:
-
$13.36
Genuine Ge part
By: Ge
Part Number: WB14X41386
Oven door won't close or lock properly? This range door latch and handle assembly secures the door during baking and self-clean cycles. DIY repair.
Do-It-Yourself Stories from Customers like You
Oven door lock quick working Jerry C. • Virginia Beach , VA • February 17, 2020
Replaced the part.
Read more
More
$58.95
- Compare At:
-
$70.74
- You Save:
-
$11.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 137539200
Dryer won't heat or shows E66 error? The thermal limiter prevents overheating by monitoring airflow. Moderate DIY repair, requires rear panel access.
Do-It-Yourself Stories from Customers like You
Frigidaire dryer error e66 then door open Nolan R. • Hoboken , NJ • February 06, 2017
My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own.
Read more
More
$37.55
- Compare At:
-
$44.68
- You Save:
-
$7.13
Genuine Ge part
By: Ge
Part Number: WE01X34284
Color: Dark Slate
The Door Strike is an OEM part for GE dryers. Positioned on the dryer frame, it securely latches the door closed during cycles. Its magnets align perfectly with the door when shut to create an air-tight barrier, enhancing energy efficiency.
Causes of failure can be normal wear, misalignment stress, or accidental damage. Over time, strikes lose effectiveness at preventing air/moisture exchange.
Symptoms of a bad door strike include:
- Excess warm air entering the dryer chamber
- The door not fully closing or latching tight
- Clothing not drying completely within expected cycles
- Buildup of lint around the door seal area
This GE part is also compatible with some Hotpoint, RCA, and Kenmore models.
More
$31.95
- Compare At:
-
$38.02
- You Save:
-
$6.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W11188327
Fix a washer that won't start or spin due to lid lock failure. This lid lock assembly prevents opening during cycles. DIY repair in about 45 minutes.
Do-It-Yourself Stories from Customers like You
Shut off. No water. Lid did not lock. Francis H. • Lutts , TN • February 14, 2021
Replaced lid switch
Read more
More
$108.40
- Compare At:
-
$129.00
- You Save:
-
$20.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8181651
Fix DL error codes and doors that won't stay shut with this washer door strike. Works with the door lock assembly. Easy 30-minute DIY repair with video.
This part fixes the following symptoms
-
Lid or door will not open
-
Lid or door won't close
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Drum spider support broken Debbie E. • Elizabethton , TN • February 14, 2015
New inner drum and front and rear outer drum; although other parts worked, still replaced the bellow and clamp, new door latch, and cleaned the hoses. Washer works great. Just like brand new. Even though matching dryer works, I am going to clean it up and replace some parts on it also.
Read more
More
$18.95
- Compare At:
-
$22.55
- You Save:
-
$3.60