Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement upper rack adjuster kit for dishwashers. Includes left and right side adjusters with rollers. Needed when original adjusters crack or break.
The repair kit has everything needed for both sides of the rack but there were no instructions so it took me some time to figure out how it all mounted on the basket. The original design was totally different than the repair kit so it would have been very beneficial to have at least a diagram that showed how everything fit together. That being said, once I figured out how all the parts fit, then it was a very easy repair. You won't reuse any of the old parts except for the end caps that snap... Read more
Replaces cracked, broken, or missing dishwasher rack stop clips. Secures upper or lower dishrack to track rail, preventing rack from sliding out too far.
My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more
Prevents water leaks around your dishwasher door. Replace if you notice pooling water on the floor or visible cracks in the seal. Verify fit by model number.
I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more
Replacement roller assembly for dishwasher lower rack. Snaps into place to restore smooth gliding. Needed when wheels break off, crack, or fall out.
Installed 2 new dishrack roller assemblies. The only tools I needed were my fingers, snapped the old assemblies out and snapped the assemblies in. Read more
Replaces broken or worn dishwasher upper rack adjuster assembly. Includes wheels and mounting hardware for smooth rack adjustment and gliding action.
I replaced the adjusters on both sides (since two rollers broke off on one and one broke off on the other). Replacement was easy, just remember to keep the clips from the original adjusters. Take the clips off, remove the adjuster, replace with the new adjuster, and replace the clips. The new adjuster comes with the rollers already attached so no need to keep the ones from when plastic axle broke on the original adjusters. Read more
Seals the bottom of your dishwasher door to prevent leaks during wash cycles. Replace if water pools on floor or seal appears flat or worn. Confirm fit.
My Whirlpool dishwasher was leaking out the bottom of the door. I replaced the gasket and the lower door seal. When I ran a test wash, it was still leaking. After reading more online, I found that it could be a cracked washer arm. The initial inspection of the washer arm looked normal but when I used my faucet to slowly pour water into the inlet of the arm, I noted that water was leaking through a seam and not just the holes where it should come out. I then tried running a wash without the... Read more
Dishwasher lower door seal prevents water leaks at the door base. Replace if you notice dripping or moisture during wash cycles. Confirm fit with your model.
Thanks to Jason and his tech people at Appliance Parts Pro, I was able to remove and replace the seal and eliminate all leaks at the bottom of the door. I have a Kitchenaide (Whirlpool) dishwasher model KUDC10IXBL1. Here is how to replace the bottom door seal. 1) Shut off breaker to dishwasher on the electrical panel. 2) Open the dishwasher door completely, and while supporting the door, remove the hex head screws that hold the outside cover. 2) Close the door carefully and slip the outside... Read more
Door balance link kit for dishwashers. Connects door springs to control door movement. Replace if rope is frayed, broken, or plastic clips are cracked or worn.
I finally decided to repair my dishwasher because the door would free fall to the floor possibly breaking the hinges. Also the top shelf was rolling out on its own every time the door was opened. I first pulled the dishwasher out of the enclosure and found that the drain hose was directly under the pump area throwing the unit completely out of level. Also the inadequate plastic and rope counterbalance on the left side was completely broken where the rope was attached to the plastic piece to the... Read more
Secures the dishwasher rack to prevent it from rolling out too far. Replace this clip if it's cracked, broken, or missing to keep your rack stable.
Replaced wheel assembly because prongs were broken and replaced track because wheel assemblies were rolling out from the track when extended. Read more
Fix dishwasher not filling with water or slow fill issues. This inlet valve controls water flow into your dishwasher. DIY repair typically takes 15-30 minutes.
Replaced the water solenoid. Read more
The Tine Row Pivot is an OEM replacement part for Whirlpool dishwashers. This component is an integral part of the upper rack assembly, allowing the tine rows to fold down or pivot inward to accommodate taller items or create additional space within th
Ordered a new one. It took about 10 seconds to install. Now it’s like brand new. Read more
Dishwasher not filling with water? A faulty water inlet valve is often the cause. This valve controls water flow into your dishwasher. DIY-friendly repair.
As mentioned, our Whirlpool Dishwasher would complete the cycle but Tablet pretty much sat in the Soap Dispenser Box nor there was any sign of water inside the Dishwasher. This happened 2 - 3 times. Hence decided to dive into what the fix was. After reviewing a bunch of Youtube Videos, understood first how a typical Dishwasher operates and what are the basic checks it does before water is let inside. So it typically first checks whether Door S/w got activated, followed by Float Switch... Read more
Dishes not drying or water not heating? This dishwasher heating element restores drying and cleaning performance. DIY-friendly repair, about 1 hour.
Followed the Appliance Parts Pros video and it took me about an hour from start to finish. I felt like the job was easy to accomplish. Read more
Clips onto the upper dishrack to hold the height adjuster assembly in place for balanced operation. Replace if cracked, broken, or missing.
I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more
If your dishwasher door won't stay closed or latch properly, this door latch assembly is the likely fix. Easy DIY repair takes about 1 hour to complete.
Changed the door switch and the dishwasher works now. Read more
Fix dishwasher leaking from the motor area with this motor to sump seal. Creates a watertight connection between pump and sump. Takes 10-20 minutes.
My dishwasher was leaking and I called to have a certified technician come to diagnose the problem. I removed the kick panel from the bottom of the machine. He turned it on and we saw that water was leaking from the bottom. He said I needed a Sump kit but it wasn't in stock. The cost was $170 plus tax and labor cost was another $140. So I talked it over with dad and ordered the Sump kit, the hose clamp and a new diverter motor as mine was yellowed with age. The cost of all these parts and... Read more