Mgs6870adq Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

Oven would broil but not get to a baking temperature. Baking element was burned through in one spot. Replaced element, temp sensor and terminal block. Works like a champ and cakes are getting baked!!! Read more

Took the stove apart*, saw where the mouse had made a nest. It was kind of like a hotel room after a rock star had used it. It was nasty, is what I'm saying. I removed the insulation, which immediately went into a garbage bag and was placed outside, whereupon I took off and nuked the site from orbit. It was the only way to be sure (actually it was disposed of in the proper manner, no nukes were detonated in the course of this repair). Anyway, I ordered the insulation from this site, which was... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

After researching the problem, I ordered a new cooling fan. My "fix-it" guy winds up in the ICU for 3 weeks! So...YouTube here I come. It appeared pretty simple in video form, except the video wasn't of my stove. All in all, what looked like no more than a 6 screw removal, turned into tearing 1/2 the stove apart. Still, only took about 2 hours start to finish. Best lesson learned, turn off the energy efficiency mode!!! Read more

• Won't start

Replaced srark module Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

Replaced It With New One Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Touch up paint Read more

Replaced the gas regulator and the oven igniter. It was not a very difficult repair.. most of the parts were easy to get to. The biggest challenge was disconnecting the gas hose from the regulator. It had "pipe dope" (sealant) on the threads. I reconnected with yellow gas pipe tape. Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

Appliances will be sold with the house so the old oven racks were no longer shiny. Replacement racks present a better looking oven. Read more