Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix F2 error codes and inaccurate oven temperatures by replacing a faulty temperature sensor. Simple 15-minute DIY repair with basic tools.
My mother's GE range was not coming up to full heat (very far from it), and I was hearing a lot of relay-clicking coming from the control board. The heating elements seemed good. I suspected the control board was faulty, but there was a chance that it might be the (*much* less expensive) temperature sensor, so I ordered both from AppliancePartsPros.com (which got the parts to me very fast) so I could try the T-sensor first. After removing the doors and the back panel of the oven, and taking out... Read more
Specially formulated cleaner for ceramic glass and smooth cooktops. Removes cooked-on food, grease, and spills without scratching. Verify fit by model.
VERY simple fix- you do not even have to pull the range out.. I ordered a new cooktop from Appliance parts Pros. The customer sales rep Alphonso was great and walked me through the general process. I could find no explicit instructions for the repair but I muddled my way through. The fix is simple on Kitchenaid/Whirpool slide in ranges. 1. Open the oven door and remove the two phillips head screws directly below the control panel that hold the panel down.2. Lift the control panel upward and... Read more
Seals oven cavity to prevent heat loss during baking and broiling. Replace if worn, cracked, or heat escapes around door. Verify fit by model number.
I removed the door, mostly so we could really clean the all the nooks and cranny's of the stove, and make the handle and gasket replacement easier. Attaching the new handle was not difficult, but did require some minor door dis-assembly. Removing the old gasket and putting on the new gasket was a breeze. The hardest part of the job was putting the door back onto the stove, but we got it done and the stove looks and works great. Read more
Burner won't turn off or stays on when set to off? This surface burner infinite switch controls heat levels. Takes 10-15 minutes to replace.
Replaced switch! Easy.... Read more
Burner not heating or won't turn on? This radiant heating element restores heat to your cooktop. DIY-friendly repair takes about 10 minutes to install.
I purchased the replacement part after seeing how easy it was to fix by watching videos online. Read more
Inner glass assembly for oven doors. Replace when cracked, shattered, or broken to restore door visibility and insulation. Verify fit with your model number.
Replaced the glass assembly with parts ordered from appliancepartspros.com. Read more
These GE screws are a 12-pack of OEM replacement parts responsible for securing and fastening various components and panels in a GE range or oven. These screws are designed with a hexagonal head, which allows for the use of a compatible wrench or socket for tightening. They are commonly used to attach sheet metal panels, brackets, and other parts within the appliance, ensuring that these components remain securely in place during operation.
This part fixes the following symptoms:
The GE screws can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more
Fixes burner stuck on, no low heat, or burner not heating. Controls temperature levels on electric range surface burners. Moderate DIY repair.
Switches needed to be replaced. Make note of where each screw comes from. They were not all the same. To remove the front panel and get to the switches, you have to partially remove the cook top. Removed 5 screws from the back to release the cooktop. Slid the cooktop back far enough to expose screws holding on the front panel. Removed 4 screws from the top and 6-8 from the bottom (opened the oven door to get to the bottom screws). Removed screws from the front panel holding the switch in... Read more
The Probe Thermistor is an OEM replacement part for GE wall ovens and ranges. Located inside the oven cavity, this temperature-sensitive probe precisely monitors interior heat to safeguard against overcooking. Causes of a faulty thermistor involve exposure to excessive cooking temperatures, moisture infiltration from spills or steam, or basic failure due to old age. Symptoms of an inadequate probe thermistor include:
This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
I looked diligently for this probe for many months and to no avail. So desperate to find it , I Goggled and found this provider for the probe. I was amazed at the timing of the receipt of the item. I received an email within hours that it had been shipped the same day and arrived at my home within less than 48 hours! The price was great and the item was easy to locate on the site.. Thank you for your attention and customer service. I will use these folks again! Read more
Range won't heat or burners stopped working? A burnt or melted terminal block may be the cause. This wiring connection hub routes power to elements. DIY repair in 10-20 minutes.
Removed damage terminal block ordered new block on line. when I received new block installed it stove works fine easy to replace. If I had not been home at the time when this happen it may had cause a big house fire. Read more
Burner won't heat or heats unevenly? This 6 inch radiant element restores consistent cooking performance. Typical DIY repair takes 30-45 minutes.
This repair was on a GE glass Cooktop range. This range has two indicator lights, a Burner On light, and a Hot Cooktop Light. The problem I was having was, the Hot Cooktop stayed on all the time (24x7), even when the cooktop surface had been off for hours and was cold. YouTubes that I viewed were all misleading on this symptom. They all pointed to the switch, which is the fix for the Burner Light staying on, not the Hot Cooktop Light staying on. I figured it out by going to the schematic.... Read more
Burner won't turn off or stays on high? This range surface element switch controls heat output. Easy DIY repair—most install in 5-10 minutes.
Installed new switches. Done in 20 minutes. Read more
Oven slow to heat or not heating at all? This hidden bake element delivers consistent bottom heat for proper baking. Moderate DIY, about 1 hour.
I called GE and they sent a tech out. $89 service call. Had I REALLY inspected the oven the hidden element had blown and separated and part of it welded itself to the inside of it's compartment. GE wanted another $350 to come back and fix it. I bought the part here for around $55 and had it running again in about an hour! Read more
Replace your oven's halogen bulb when the interior light burns out or dims. Illuminates the oven cavity so you can monitor cooking without opening the door.
Ordered new light bulb Read more
10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.
All of the information on the web repair sites said "replace the hinges as the springs are worn out." Didn't fix the problem. The top of the door still wouldn't seal, and the. Leaning latch wouldn't catch the door unless you pressed on the door. The inside panel of the door was fatigued. Too many turkeys were set on the door over the years. The hinges are attached to that inside panel, so the stress points were bent over time. I replaced the inside steel panel. Took about an hour. Was able... Read more
Pilot indicator light mounts in the control panel and illuminates when a surface element or heating circuit is powered. Replace if burned out or stuck on.