Sdg109wa Parts

Dryer cylinder belt transmits motor power to spin the drum. Replace if belt is worn, frayed, or broken causing drum not to turn. Verify fit with model number.

Maintains tension on the drive belt. Replace if the wheel is cracked, bearing is worn, or assembly is broken to restore smooth, quiet drum rotation.

Idler lever assembly with bearing and wheel for dryers. Maintains belt tension for smooth drum rotation. Replace if cracked, worn, or causing squeaking.

Dryer won't start or stops mid-cycle? A worn door catch prevents secure latching. This assembly holds the door shut so your dryer runs. DIY-friendly repair.

This drum support roller installs inside your dryer to support and guide the drum as it rotates. Replace if cracked, worn, or causing noise during operation.

Dryer not heating or overheating? A failed limit thermostat stops heat when temps climb too high. Simple DIY fix restores safe, reliable drying.

Clothes not drying or taking too long? This dryer blower wheel circulates air through the drum to dry clothes efficiently. Mounts on motor shaft.

Dryer not powering on or overheating at the power connection? This terminal block assembly restores safe electrical connections. Moderate DIY repair.

Rotating drum assembly that tumbles laundry during drying. Replace if dented, rusted, or causing noise and uneven drying. Confirm fit with your model.

Threaded metal shaft that mounts the idler roller in dryers and washer-dryer combos. Replace if bent, worn, or stripped threads prevent secure roller installation.

This front bulkhead assembly forms the dryer's front drum support and air seal. Replacing a worn or damaged bulkhead restores smooth drum rotation, reduces noise, and helps maintain proper airflow for consistent drying performance.

• Supports and aligns the drum at the front to prevent rubbing and scraping
• Helps seal the lint/air path so heat stays in the drum and exhaust flows correctly
• Air leaks at the front bulkhead can contribute to long dry times or lint in the cabinet

• Disconnect power and gas supply and allow the dryer to cool before servicing
• Remove the front panel/door assembly; support the drum before detaching the old bulkhead
• Transfer any model-specific components from the original bulkhead and ensure seals/glides are correctly positioned
• After installation, rotate the drum by hand to verify clearances, then reassemble and test

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

If your dryer is vibrating excessively or making loud thumping noises, a worn drum roller bracket may be the cause. This bracket restores smooth rotation.

Fix a dryer that won't heat or overheats with this temperature-sensing thermostat. Monitors and regulates heat for safe, consistent drying performance.

This switch knob fits onto the control switch shaft so you can select settings and operate the machine. Replacing a cracked, stripped, or missing knob restores smooth, reliable control and keeps daily use straightforward. What it does:

• Fits over the control switch shaft to turn the switch and choose settings
• Restores a secure grip and clear position when selecting options
• Helps resolve issues like slipping when turning or a knob that won't stay attached
• Common symptoms: cracked knob, stripped insert, loose or missing knob, difficulty selecting settings

• 1 switch knob

• Disconnect power before servicing
• Pull the old knob straight off; remove any retaining clip or set screw if present and save it
• Align the flat/D-shaft orientation and press the new knob fully onto the switch shaft
• Test the switch through all positions to confirm proper engagement

Seals the back of the dryer drum to prevent air leaks and maintain proper alignment. Replace if you notice poor drying or air escaping. Confirm fit with your model.