Need Help?
Call or text
Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.
With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more
Replaces worn or leaking shock absorbers that cause excessive vibration and wobbling during spin cycles. Restores stability and smooth operation.
My washing machine was making a loud thumping sound and bouncing around a bit. Research suggested that it could be bearings and/or the spider shaft assembly. After watching the instruction videos to replace the spider or bearings, I seen you need to replace both the shaft seal and tub gasket to get to the spider and bearings. So I ordered both and waited for them to arrive. Plan was to disassemble the washer, determine what was needed, order the additional parts needed, and reassemble after the... Read more
Washer won't start or shows door error? This door lock switch assembly fixes door latch issues. DIY-friendly repair with video guide, typically done in 15 minutes.
Replaced door lock switch. Read more
Secures the door boot gasket on your washer. Replace if seal pops off, leaks occur, or spring wire breaks. Confirm fit with your model number.
Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more
Washer not filling with water or showing 4E error? The water inlet valve controls flow into your machine. DIY repair in 15-40 minutes with video guide.
I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more
The Washer Spider and Shaft Assembly is essential for maintaining the smooth operation of your washing machine. This genuine OEM part is specifically designed to ensure compatibility with a wide range of Samsung washer models, providing a secure and precise fit. Crafted from high-quality materials, the spider and shaft assembly offers exceptional durability and reliability, minimizing the risk of unexpected breakdowns. By replacing a worn or damaged assembly with this genuine OEM part, you can restore your washers performance, enabling efficient and balanced spin cycles. Installation is straightforward, allowing you to quickly get your appliance back up and running without the need for professional assistance. Additionally, this assembly helps extend the lifespan of your washer, saving you time and money on potential repairs. Choosing the Washer Spider and Shaft Assembly ensures that your Samsung washer functions optimally, delivering the best cleaning results for your laundry needs. Trust in this quality replacement part to enhance the performance and longevity of your appliance.
Luckily happen to be walking by when machine started to make "grinding" noise as washer tub started to hit plastic tub. Assuming by shutting down machine, prevented any more damage. Aside from noise, when we opened door, tub appeared "crooked" tilted back a lot further then normal. When we removed the rubber door seal, could spin drum and hear and see the wobble and grinding. Internet told us the possibilities and so we proceeded to break down the machine. A drill with Philips bit and... Read more
Fix a washer door that won't close or lock with this door latch assembly. Typical repair for broken latches takes about 15 minutes. Easy DIY install.
I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more
Washer Assembly Bolt is essential for securing components in your Samsung washer. Crafted as a genuine OEM part, it ensures durability and reliability in your appliance. This bolt assembly is specifically designed for Samsung washers, guaranteeing a perfect fit and easy installation. Made from high-quality materials, it withstands the demands of regular use, providing long-lasting performance. Replacing worn or damaged bolts with this genuine OEM washer assembly bolt helps maintain the structural integrity of your machine, ensuring it operates smoothly and efficiently. By choosing this reliable part, you can confidently restore your washer to optimal working condition, enhancing its lifespan and performance. Trust in this Washer Assembly Bolt to deliver the functionality you need for a dependable laundry experience.
I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more
Replace your washer door boot seal if you notice water leaking from the door area. This rubber gasket creates a watertight seal around the door opening.
Ordered a new outer door seal and watched their video before replacing. Easy to follow the video and it took me less than 30 min to complete repair. A small amount of diluted dishwashing liquid on the new seal lip makes the install much easier. Read more
Fix excessive vibration and loud spinning noise in your washer. Balance ring assembly stabilizes the drum during spin cycles. Advanced DIY repair.
With all the bouncing around the shocks appeared to be done in but that was not the issue. The key was the balance ring. It had leaked all the fluid out causing all the beads to clump. This caused the drum to wobble wildly and not spin at speed. Getting to the ring to replace it is not a trivial task and took me several hours. Would have been much easier with help as the drum is quite heavy. The on-line video's are very handy and should be watched before attempting this job to save you a... Read more
Secures your washer's door boot seal to prevent water leaks. Replace if you notice leaking during cycles or a loose seal. Confirm fit with your model.
I ordered new door gasket, front and rear clamp for gasket and installed them. Read more
Fix a washer that won't fill with water or leaks onto the floor. This water inlet valve controls water flow into your machine. DIY repair in 10 minutes.
The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more
Replacement glass panel for washer door. Installs on front-load washer doors. Order when glass is cracked, shattered, or broken. Includes installation video.
I looked up my model number on the site, and found my parts needed. J then watched a video from repair clinic on you tube. The video was sr sight forward, and made the repair easy. I have repaired washers and dryers for numerous people following the same process. Doing this has saved hundreds of dollars in labor charges. Read more
Fix leaks or mold buildup with a new washer drain hose. Channels water away from the drum. Moderate DIY repair—requires back panel removal.
Bought and installed a new drain hose. It required removing the back access panel and loosening a pinch clamp that holds the hose on its male outlet end, and threading the hose out the back of the washer. Read more
The Washer Dispenser Drawer Housing Cover Assembly is designed to seamlessly replace the housing cover of your washer's dispenser drawer. This genuine OEM part ensures a perfect fit and reliable performance, maintaining the functionality of your Samsung washer. Crafted from durable materials, the assembly protects the internal components of the dispenser drawer, preventing leaks and ensuring smooth operation. Installing this cover is straightforward, allowing you to restore your washer quickly and efficiently without the need for professional assistance. The Washer Dispenser Drawer Housing Cover Assembly not only enhances the appearance of your appliance but also extends its lifespan by safeguarding critical parts from wear and tear. Compatible with a variety of Samsung washer models, this genuine OEM part guarantees compatibility and durability. By choosing this high-quality replacement, you ensure your washer continues to operate effectively, providing you with the dependable performance you expect from your appliance. Enhance your washerGÇÖs functionality and maintain its pristine condition with this essential dispenser drawer housing cover assembly.
Ordered new dispenser assembly and replaced it. Fixed the problem. Read more
Fix washer not draining or leaking water on the floor with a new tub to pump drain hose. Common DIY repair, typically takes 15-45 minutes to install.
I am 68 Years old and I had this PUMP DRAIN part in place and working in around 15 minutes Read more