Dacor Parts

• Will not agitate
• Spins slowly

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Ice maker dispenses too little ice
• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

My first hour: I investigated first by pulling out refridgerator to see if the water line hose was kinked. I started under the kitchen sink where it begins, coming from faucet water supply. Then I followed it to the back of the fridge to see if anything looked odd. Next I went to the ice maker itself. I investigated the ice maker by removing the freezer food sliding tray and hanging tray, and then unscrewing the door off the slides. When I looked inside at the ice maker, I saw the tube where... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

I replaced the icemaker. It was fairly easy, with the most difficult part being access to the icemaker in the bottom freezer. I loosened two screws, removed one additional screw, disconnected the wiring and removed the old icemaker. I mounted the wiring harness and ice level sensor arm from the old unit onto the new icemaker and installed it with no problems. I wish I'd done this months ago instead of repeatedly attempting to repair the old icemaker. Read more

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

• Frost buildup
• Leaking

The drain tube for for the defrost cycle seemed to be blocked, so I googled the repair & it sent me to AppliancePartsPros. Obviously, there's a design problem with this model since many other people have the same issue. This tube is an upgrade on the original for my KitchenAid model (design flaw). Since installation 4 days ago, I have had no leaks - awesome! The video for installation of the new tube on AppliancePartsPros was excellent. Two additions to the video: 1) I used a hair dryer... Read more

• Not dispensing water
• Ice maker dispenses too little ice
• Ice maker won't dispense ice
• Ice maker not making ice

Ordered part and replaced it Read more

Looked up parts based on fridge model number, watched videos, and replaced parts using just a few tools... easy. Parts came quick, well packaged. After 16 years, plastic parts deteriorate and break. The fridge was operating fine, but the drawers and covers were failing. Much cheaper to replace a few parts ($$-$$$) than buy a new fridge ($$$$). The new parts matched up exactly to old ones. The videos were very helpful, but not perfect... for the Crisper Frame, there was a structural metal... Read more

• Clicking sound
• Won't start
• Freezer section too warm
• Fridge too warm

Removed back cover and installed new start device. Plugged in refridgerator and it runs like new. Read more

Door gasket was easy to remove and reinstall. Original gasket was penetrated while cleaning food stuff from folds in the seal below the frig doors. (Gasket is very fragile so don't try to expand the folds while cleaning. I used my finger and a paper towel but in hindsight should have used a Q-Tip. Also, when installing the new gasket you have to be sure the seam folds over the edge of the door and doesn't get caught underneath. Read more

The tray was simple, pick up the old one, pop in the new one. The gasket for my refrigerator was almost as easy. When I received the part I opened it up and let it lay flat for about 3 days (probably overkill). The old gasket popped right out and the new one went in really easy. The entire job took me about 10 minutes to do, no tools required. I do recommend that you start with corners and work your way to the middle of each side. I found that would prevent any stretching. You also need to... Read more

I watched the video on replacing the switch on a side freezer where prying out to original switch did not look difficult. I then got on the floor and tried to pry out my switch. Had a terrible time (locking tab or switch body hardened with time?) and mangled the switch terribly and the upper panel of the freezer somewhat, but the switch did come out. AND THEN the top freezer panel with the switch and light assembly fell out into my hands! I was able to unplug one Molex connector and the... Read more

• Ice maker won't dispense ice
• Ice maker not making ice

After finding out the cost that we would have to pay for the repair locally, I went to Appliance parts pro.com. with the intention of finding out the cost for parts. We had been quoted $100 for the first hour which included repair if it could be done under the first hour plus parts. And they added that the typical repair for the ice maker was between $200 and $500. Fortunately we are very organized and had the original paperwork of the refrigerator which has all parts and numbers for the... Read more

• Fridge too cold
• Freezer too cold
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

After taking the two vegetable drawers out from above, the glass shelf, the pantry drawer and the cross support for the glass, you can get to the two recessed hex head screws holding the end cap. You will need to transfer the metal drawer slide to the new cap, but it doesn't need to come off first. When the end cap is loose, gently rotate it toward the front. Once the humidity control slide is at 90 degrees from the back of the refrigerator, the tab holding it in place will slip out easily.... Read more