Need Help?
Call or text
Oven won't heat or shuts off during baking? A faulty thermal fuse cuts power when detecting excessive heat. This safety device protects your range.
The F9 error code is supposed to indicate that the door lock mechanism has failed. My oven would give the F9 code and turn off during normal baking at 400 F after about 30-40 minutes. It turns out that GE must have programmed the error codes incorrectly in my model, because the real problem was that my control board cooling fan was no longer functional, and one of the two thermal switches was shutting off the unit when the control board area got too hot. AppliancePartsPros.com is one of the... Read more
The Probe Thermistor is an OEM replacement part for GE wall ovens and ranges. Located inside the oven cavity, this temperature-sensitive probe precisely monitors interior heat to safeguard against overcooking. Causes of a faulty thermistor involve exposure to excessive cooking temperatures, moisture infiltration from spills or steam, or basic failure due to old age. Symptoms of an inadequate probe thermistor include:
This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
I looked diligently for this probe for many months and to no avail. So desperate to find it , I Goggled and found this provider for the probe. I was amazed at the timing of the receipt of the item. I received an email within hours that it had been shipped the same day and arrived at my home within less than 48 hours! The price was great and the item was easy to locate on the site.. Thank you for your attention and customer service. I will use these folks again! Read more
Broiler pan for ranges and ovens. Installs in main oven cavity to hold food under broiler element. Replace if cracked, warped, or heavily stained.
Fast delivery, great service Read more
Oven not broiling or browning food? The broil element provides high heat at the top of the oven. Simple 5-10 minute DIY fix with basic tools.
Would advise before doing this repair to watch the video for it. It is not a plug in connection anymore like older ovens. The key is to keep the connecting wires from the oven from falling or pulling into the inner wall of the oven. The wires may not come very far out away from the wall of the oven so make sure to secure them. The video shows a good way to do that. If you have an in wall oven this is very important because it would hard and time consuming to pull the oven out of the wall to... Read more
Replace your oven's halogen bulb when the interior light burns out or dims. Illuminates the oven cavity so you can monitor cooking without opening the door.
Ordered new light bulb Read more
Replacement inner glass window assembly for oven doors. Installs between door panels for clear visibility while cooking. Order when cracked, shattered, or broken.
Chatted on-line with one of the customer service representatives. He helped me select and order the correct part and also gave some basic instructions. Part arrived with several days of ordering. Read more
Ranges, wall ovens, and microwaves require a hub blade assembly in order to operate efficiently. The hub blade works inside the device to help with the various heating cycles. With use, because of misuse, or as a result of accidental damage, the hub blade may stop working. When this component is no longer functioning, a replacement part is required. If the oven isn't warming correctly, the hub blade assembly may be the issue.Replacing the hub blade assembly is a simple process. A screwdriver, socket set, adjustable wrench, and wrench set are required. Always disconnect appliances before replacing components. Wear gloves for safety. The hub blade assembly is located inside the oven. To access it, the back of the appliance has to be removed. Be sure all parts are replaced and secured before turning the device back on.This hub blade assembly is a genuine OEM replacement part. It is sourced directly from the manufacturer. The part is sold as an individual unit and made of high-quality, durable materials. The hub blade assembly can be installed in various models of ranges, wall ovens, and microwave oven combination appliances. It is compatible with General Electric, Hotpoint, and RCA brand devices.
The oven was so loud, it was hard to talk to someone in the kitchen. We replaced the motor and the fan blade. 1. Turn off power to the oven. 2. Remove the oven doors 3. Remove the cover for the fan. 4. Turn the fan blade nut clockwise to loosen( it's opposite of normal) - Save the nut and the small clip that is behind the fan as you'll need them again. 5. Remove the screws that hold oven to the kitchen cabinet frame. 6. Slide oven out of kitchen cabinet and place on the floor - it takes 2... Read more
10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.
All of the information on the web repair sites said "replace the hinges as the springs are worn out." Didn't fix the problem. The top of the door still wouldn't seal, and the. Leaning latch wouldn't catch the door unless you pressed on the door. The inside panel of the door was fatigued. Too many turkeys were set on the door over the years. The hinges are attached to that inside panel, so the stress points were bent over time. I replaced the inside steel panel. Took about an hour. Was able... Read more
Fix a noisy or non-working convection fan with this motor assembly. Restores even heating and airflow in your oven. Takes about 30 minutes to install.
Very easy fix. Turned of power at breaker. Removed oven door by lowering two "keepers" on the hinges for the oven door and sliding the door out of the oven. Removed the trim plate at bottom of oven by pushing it up.. Removed 2 screws that mount to the frame of the cabinet at the bottom that the trim plate hangs from. Then removed 4 screws that hold the oven into the cabinet at either side of the oven. Put two 5 gallon buckets in front of the oven and slid the oven out onto the side-by-side... Read more
ST10-16 X 7/16"
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
This is a genuine OEM replacement nut that is used on convection oven fans. This nut holds the fan onto the spindle. If the nut becomes lost during repairs to the fan, it will need to be replaced before the fan will work. This nut locks the fan to the spindle to turn and move the air around inside the oven. The fan helps the food to cook more evenly and reduces areas in the oven that are not cool enough or hot enough. If the fan is not working, the convection oven will not cook correctly.Convection ovens are different from regular ovens, and the fan is part of the reason. Convection ovens use the fan and an exhaust system to move the heat around inside the oven to cook food more evenly and faster. Many convection ovens have a setting that allows the oven to be used as a regular oven. If the nut is missing and the fan is inoperable, the oven can be used for regular cooking if it has this feature. Otherwise, the convection oven should not be used until the nut is replaced.This nut is a silver metal replacement part that is sold individually. It is designed for use in convection ovens made by GE and Kenmore.
I took the cover off and the fan had separated from the bushing. Ordered a new fan and nut and it took all of 5 minutes to replace. Probably saved $159.99 service call repair and that is with a coupon. Any one can do this repair, just make sure the oven is cold as you will come in contact with metal parts. Read more
Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.
We replaced the broken door hinge. Read more
Seals the oven door to retain heat and improve baking efficiency. Replace when worn, cracked, or rigid to stop heat leaks. Verify fit by model number.
Simple removal by hand and replace attached pins. Read more
Black. 8-18 AB HXW 3/8
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.
I was very pleased to get the glass on time and it was a perfect match. The only thing I had trouble was to get the screws required to fix. The screws were not available, so spend too much time trying find equivalent screws in homedepot. Read more
Oven convection fan not working or making noise? This shaft-mount fan blade restores proper airflow and cooling. Easy DIY repair in under an hour.
Ordered fan assembly. Not difficult to install at all. Remove the back cover, remove the fan cover inside the oven, remove the motor/fan assembly and put it all together. Easy. Read more