Mer5552saw Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Little to no heat when broiling

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

• Little to no heat when baking
• Oven not heating evenly
• Element will not heat
• Oven is too hot

I finally found the right serial number and found the part at Appliance Parts Pros. I was skeptical that they would send the element that had the correct rear brace fixture. when it came 2 days later i opened the box the Part was correct and it took about 15 minutes to replace since there are only two screws. My oven works fine now. THX Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

• Element will not heat

1. Went online where I watched video about heat control for this Maytag. I then found AppliancePartsPros using Google. I ordered the part and In three days the part arrived. I installed the part and now the problem has been corrected. Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

1) ordered new boiler element after searching for oven/stove model # online 2) unplugged oven 3) removed 2 screws holding element in place 4) pulled out the element and a length of wires attached to the element (enough that the wires wouldn't pull back into the hole after detached) 5) used needle-nosed pliers to detach wire clamps, noting which wire attached to which side of the old element 6) removed old element and its pieces from the bottom of oven 7) attached wires to new element,... Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

Appliances will be sold with the house so the old oven racks were no longer shiny. Replacement racks present a better looking oven. Read more

• Little to no heat when broiling

I had the choice of spending $2K on another double oven stove or $60 on two elements. (I felt more secure about replacing both bake and broil elements just in case the fire had damaged the bake element) It was an easy decision and quick replacement! Power was already off to the stove so I cleaned up the fire retardent mess. I even found easy instructions dismantling the oven door in order to clean the powder residue from between the glass. I then removed the rack and remaining old elements. I... Read more

• Element will not heat
• Won't start

Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more

We bought replacements which fit very well and the burner elements are level again! Read more

I used your chat and found out the year my stove was made. He also told me what part to order as one of the burners had stopped heating up. We watched the video on how to install it. My friend installed it and my stove burner now works. Read more

We bought replacements which fit very well and the burner elements are level again! Read more

These drip pans fit! I had bought some from a local big box store and they didn't fit. I only wish they still made them without the holes in the bottom of the drip pan. How's that supposed to hold a boil-over? But that's the manufacturer. AppliancePartsPros have always sent me orders right on time. Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more