Outer Ecb Parts

The User Interface Control Board is an OEM part for GE dishwashers. It is responsible for controlling and managing the settings and functions of the dishwasher. It allows users to select different wash cycles, adjust settings, and monitor the progress of the dishwasher.

A bad User Interface Control Board can occur due to electrical malfunctions, damage caused by power surges, or wear and tear over time. If the control board becomes unresponsive, displays error codes, or fails to operate the dishwasher properly, it may be time to replace the User Interface Control Board.

Symptoms of a bad User Interface Control Board include:

• Unresponsive buttons or touchpad.
• Error codes displayed on the control panel.
• Inability to select or change wash cycles.
• Display screen not functioning properly.

If you're experiencing any of these issues, it's time to replace the User Interface Control Board with this genuine GE part. Regain full control over your dishwasher's settings and ensure an efficient cleaning. This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Service Machine Control is an OEM component specifically designed for GE dishwashers. As the main control board, it regulates all wash cycles including temperature, filtration, spray arm rotation, drying functions and end of cycle signals.

Causes of a faulty service machine control include normal wear and tear over time. Electronic failures or water exposure from plumbing issues can also trigger malfunctions.

Symptoms of a failing control board are:

• Inability to progress through cycles fully
• Flashing error codes during washes
• Inconsistent wash and rinse performance
• Component damage from power overload issues

Replacing it with this genuine GE OEM part restores optimal cycle handling. Proper controls are essential for sanitizing every wash. The part is also compatible with Hotpoint, RCA and some Kenmore models.

The Main Control Board is an OEM replacement part for GE dishwashers. It serves as the central control unit for your dishwasher, responsible for coordinating and regulating various functions and cycles. It controls functions such as water temperature, cycle duration, and detergent dispensing. 

A bad Main Control Board can result in a range of issues, including cycle irregularities, error codes, or a complete failure of the dishwasher to function. Causes of a bad Main Control Board can include electrical failures, power surges, or damage due to moisture.

Symptoms of a bad Main Control Board include:

• Inconsistent or erratic cycle behavior
• Error codes or error messages displayed on the control panel
• Inability to start or complete a cycle
• Unresponsive control panel buttons

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Timer is an OEM replacement part for Whirlpool dryers. It is a critical component that controls the timing and sequence of the various drying cycles, ensuring the machine operates correctly and efficiently.

Causes of needing to replace the dryer timer can include general wear and tear over time, electrical malfunctions, damage from power surges or voltage fluctuations, or moisture or water exposure within the timer itself.

Symptoms of a bad dryer timer include:

• The dryer failing to advance through the complete cycle or getting stuck in one part of the cycle
• Cycles running for an incorrect duration (too short or too long)
• The dryer failing to heat, tumble, or stop at the appropriate times

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Control Oven TO9 is an OEM part for GE ranges. This part manages the oven's various functions, including temperature regulation, cooking modes, and timer settings. It serves as the central interface for the user to control the oven's operations, ensuring precise and reliable cooking performance.

Causes of a bad control module can include electrical surges, general wear and tear, or physical damage from impacts or spills.

Symptoms of a bad control oven module include:

• Unresponsive or malfunctioning buttons and dials
• Incorrect temperature readings or inconsistent heating
• Display not functioning properly
• Oven not turning on or shutting off unexpectedly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Includes black knob

The Speed Control Assembly is an OEM part for Whirlpool mixers, integral to managing the mixing speed to accommodate various ingredients and recipes efficiently. This assembly is crucial for the precise control over the mixer's speed, ensuring that your mixing tasks are performed with the desired consistency and texture.   Speed Control Assembly has been updated by Whirlpool and no longer includes the ribbon attached. 

Common causes of a faulty Speed Control Assembly can vary, such as electrical problems resulting in erratic mixer speeds, wear and tear from regular usage, physical damage to the control assembly, or faulty wiring and connections within the mixer.

Symptoms of a bad Speed Control Assembly include:

• The mixer operates at one speed regardless of the setting
• Inability to adjust the mixer's speed
• The mixer fails to start or exhibits intermittent stopping during use
• Unusual noises or behavior when changing speeds

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Configured Service Machine Control Board is an OEM component designed specifically for GE dishwashers. It serves as the central processor that monitors all cycle phases including wash, rinse, dry, and sanitization. Precise controls are paramount for thorough cleaning performance.

The causes of a board needing replacement can relate to water exposure compromising electrical circuits over time. Regular operational wear may also induce failures.

Symptoms of a faulty control board involve:

• Inoperable or interrupted wash cycles
• Inaccurate temperature or unclear error codes
• Component damage from electrical overloads
• Signal issues preventing desired settings

The configured service machine control board is compatible with Hotpoint, RCA, and select Kenmore models.

The Timer is an OEM part for GE dryers. It's a component that controls the duration of the drying cycles, ensuring clothes are dried efficiently and not overexposed to heat, which can cause damage. The timer regulates the start, duration, and end of each cycle, playing a pivotal role in the operation of the dryer.

Causes of a malfunctioning timer can include wear and tear from regular use, electrical failures that impede the timer's movement, and physical damage to the timer knob or internal components.

Symptoms of a bad Timer include:

• The dryer doesn't start or complete a cycle
• Cycles run longer or shorter than programmed
• The timer knob does not advance or is stuck

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This main control board is the washer's central electronic brain, coordinating cycles, motor and valve operation, and safety checks. Replacing a failed board can restore normal starts, fills, agitation/spin, and reliable cycle completion.

• Manages cycle timing and power to the drive motor, drain pump, and water inlet valves
• Monitors inputs from the lid lock and other sensors for safe, accurate operation
• Interfaces with the user controls to run the selected wash program
• Typical failure symptoms: won't start or power up; no fill/agitate/spin/drain; stops mid-cycle; error codes or unresponsive controls

• Disconnect power before servicing and handle the board with ESD protection
• Access the control at the top/rear area, transfer connectors one at a time to the same positions, and secure the board in the original mounting
• After installation, restore power and run the unit's diagnostic/service mode to verify operation; some models may require a configuration/personality step per the tech sheet

The User Interface Control Board is an OEM part for GE dishwashers. It serves as the main control panel, allowing users to select and monitor various wash cycles and settings. This control board interfaces with the dishwasher's electronic system to ensure proper operation.

Causes of a bad control board can include electrical issues, exposure to moisture, or general wear and tear over time. Damage to the circuitry or components can also impair its functionality.

Symptoms of a bad user interface control board include:

• Unresponsive or malfunctioning buttons
• Display screen not working or showing incorrect information
• Inability to select or change wash cycles
• Dishwasher not starting or stopping unexpectedly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Timer is an OEM part for Whirlpool dryers. This timer is a control mechanism that allows you to set the drying time for various fabrics and load sizes. It works by regulating the duration of the drying cycle to ensure clothes are dried efficiently without overuse of energy or excessive wear on fabrics.  

Causes of a bad dryer timer can vary from electrical problems within the timer mechanism, such as short circuits or burnt contacts, to mechanical failures like stripped gears. 

Symptoms of a bad timer:

• The dryer not starting or failing to stop at the end of a cycle 
• Clothes remaining damp or overly dry 
• The dryer operating only at a specific setting 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Timer is an OEM part for GE dryers that is responsible for ensuring that the dryer operates for the set amount of time, enabling different cycles and functions to occur at the correct intervals. The timer regulates the start, duration, and end of each drying cycle. Over time, timers can wear out or malfunction due to electrical issues or mechanical wear, leading to problems with the dryer's operation.

Symptoms of a bad Timer include:

• The dryer failing to start or stop at the proper times.
• Only certain cycles working.
• The dryer running continuously without shutting off.

Causes of a bad timer can stem from a variety of issues, including electrical shorts, worn contacts within the timer mechanism. Regular usage and age can contribute to these problems.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Timer is an OEM part for GE dryers. It is responsible for controlling the duration of the drying cycles by regulating the electrical components within the dryer. This component ensures that the dryer runs for the correct amount of time based on the selected settings, enabling efficient and effective drying of clothes.

Causes of a bad timer can include electrical failures, worn-out contacts, or internal mechanical issues. A malfunctioning timer can lead to improper cycle durations, the dryer not starting, or stopping prematurely.

Symptoms of a bad timer include:

• The dryer not advancing through the drying cycles
• The dryer stopping mid-cycle or running continuously without stopping
• The timer knob not moving or making unusual noises
• Inconsistent drying times or clothes not drying properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Phase Control Board is an OEM part for Whirlpool mixers. It regulates the mixer's motor speed by controlling the electrical current flowing to the motor, ensuring precise speed settings and smooth operation. This board is essential for achieving consistent mixing results and handling various mixing tasks effectively.

Causes of a bad phase control board can include electrical surges, wear and tear from regular use, or component failure due to overheating. A faulty control board can lead to inconsistent speeds, affecting the mixer's performance and potentially damaging the motor.

Symptoms of a bad phase control board include:

• Inconsistent or erratic mixer speeds
• Mixer not starting or stopping unexpectedly
• Unusual noises or burning smells during operation
• Mixer operating at only one speed regardless of setting

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: This is the 120-volt phase control board. For the 240-volt board use W11174552.

The Configured UI Board is an OEM part for GE dishwashers. It serves as the central control unit, managing all operations of the dishwasher including cycles, temperatures, water levels, and timings. The UI board has all necessary wiring and components factory-installed to seamlessly interface with existing control panels and buttons.

Causes of a bad UI board can include water damage, cracked or loose circuitry, or failures of electronic components over time. Without a functioning UI board, the dishwasher cannot run cycles or sense user inputs.

Symptoms of a bad UI board include:

• The dishwasher not starting or running cycles
• Control panel malfunctions like unresponsive buttons or odd error codes
• Inability to select desired cycles or change settings
• Appliance failing to self-diagnose or display problems

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

The Clock is an OEM part for Frigidaire ovens and ranges. It is the central electronic component that regulates and monitors oven functions such as bake, broil, convection, temperature controls, and timers.

Causes can be failures in the integrated circuitry, damaged connectors or traces on the board, or water or other environmental damage over time.

Symptoms of a clock include:

• Failure of oven elements to heat properly
• Unresponsive or inaccurate temperature displays
• Irregular timed baking or errors flashing
• Problems with convection or baking modes
• Power issues such as the oven not turning on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.