Outer Ecb Parts

I started with Google searches for the problem, using the dishwasher model number to narrow down the number of results. When I found several posts in the forum on AppliancePartsPros.com from other people having the same problem with the same dishwasher, as well as solutions that involved replacing the control board, I decided to start with that. The repair was very easy, especially with the help of clear and well-paced videos showing exactly what to do and what to look for. I was able to... Read more

Indicator light would blink three times, make a sound, but the dishwasher would not run. After making sure there were no obstructions, no problems with seals, filters, and latch clean, I cut the power off and back on. The Dishwasher worked for a few more times. After that, cutting the power off and on no longer worked. I figured out what buttons to press and hold to find the error code (start/stop and cycle select), saw code 815, and then did a "hard reset" by pressing and holding other... Read more

After calling Whirlpool customer support learned that a replacement timer would be $136. The CSR gave me the part number needed. Online I found AppliacePartsPros. I called and got a very personable CSR who took my order. I was assured the part was a genuine, new--not rebuilt--timer. My order was placed in minutes. Although I ordered standard shipping and my part arrived in 2 days!! Unfortunately Whirlpool had given me the wrong part number so I contacted AppliancePartsPros and reordered... Read more

Two weeks ago, my dishwasher would not run. It would beep three times when you pushed the start button: the same signal it gives when the door is open. I used the troubleshooting steps I found at applianceblog.com to do a hard reset. (Hold START and WASH TEMP for five seconds, close the door, and wait 3 minutes) After that, it worked for about one week. When it started having the same issue again, the hard reset did not work. I lowered the control board and could see that there were no lights.... Read more

Ordered a new timer and knob. The husband was able to fix in about 20 minutes and now works like new. Read more

Replaced control board myself. Easy. Read more

My GE dishwasher (GDT605PMM0ES) had started going in and out of service but if I unplugged it and plugged it back in it would work a few more times. Then one day that old trick didn't work anymore. Looked at what might be the issue on the internet and most signs pointed to the configured service machine control board or the configured Ui board. I ordered both, not really which was bad, but started with the Ui board first because the service machine control board showed it was receiving... Read more

The fix was very easy. Control assembly is easy to access by removing 5 phillips screws. Unplug the wiring from the old assembly being careful to note which wire goes to which connector. Install the new assembly and connect the wiring. Read more

GE Washer m/n GTW460ASJ6WW would allow other fill levels, but when set to "super" it would never stop filling. Checked water inlet valve (by initiating a fill and unplugging the unit) to see if the inlet valve was sticking open, that was not the issue. Decided to replace the board even though it is a significant fraction of the cost of a new washer. Local appliance stores didn't have the board but APP did, and of course, they are open 24/7 while my local part stores have decided the weekend is... Read more

Ordered new timer and fixed the problem Read more

The control went thru a month or so of erratic behavior; the display would come on and flash and beep without any input on my part. Then it died completely. I did a little research on the GE website and determined likely cause waa a defective user interface board. I found AppliancePartsPros.com and contacted their tech support, who directed me to check the output of the control board across 2 pins for 13.5v DC. I did this, and measured 13.8v, so control board was good. When I reconnected the... Read more

• Shuts off too soon

After taking the timer apart to see why it would not turn I found the timer motor was jammed. Taking the motor apart I found a broken gear. Looked up the model number of the dryer and found a new timer assembly thru appliancepartspros.com I ordered, a very easy process, received the part 2 days later. Installed the assembly in about 5minutes and had the dryer back up and running Read more

I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at... Read more

Replaced the control board on bottom of machine Read more

I first felt along each heating element (bake and broil) hoping to find a rough or blistered place on them. But they were both smooth with no irregular places. (replacing the elements would have been the easiest and cheapest repair. Pulled the back off the range (unplugged, of course) - checked wiring. There were no loose connections or burned wiring. I disconnected the elements and checked them with a ohmmeter (VOM) and both had continuity. Discovered that both elements used the same... Read more

I researched online and found that it was probably one of two things wrong: the heat probe or the control board (clock). Since the probe was less expensive, I ordered that on Appliance PartsPros. It arrived SO quickly, and with the repair video I easily replaced it. BUT... it still got the F10 reading. Sigh. So I found a local appliance repairman (I didn't want to replace a more expensive item if it turned out I was wrong). He was a good one: he listened to my story, said he was sure it was the... Read more