Pfw950spt3ds Parts

This is the drain pump and filter assembly for select washing machines. It moves wastewater out of the tub while trapping lint and debris to help prevent clogs and protect the pump.

• Pumps water out during drain cycles and spin
• Integrated filter screens out debris to maintain flow
• Can help resolve slow or no drain, standing water, or draining-related errors
• May reduce unusual humming/buzzing from a failing pump

• Unplug the washer and turn off water supply before servicing
• Have towels or a shallow pan ready—residual water will drain when hoses are removed
• Note hose and wire positions before transfer; swap clamps and connectors one-for-one
• After installation, run a short drain/spin to check for leaks and proper operation

The Door Lock is an OEM part for GE washing machines. This part secures the door during operation, ensuring the washer does not run with the door open. This lock mechanism prevents water leakage and provides safety by preventing accidental opening during the wash or spin cycles.

Causes of a bad Door Lock can include wear and tear from frequent use, electrical faults such as short circuits or motor failures, and mechanical issues like broken or worn-out latch components.

Symptoms of a bad Door Lock include:

• The washing machine not starting or responding to the start command
• The door not locking or unlocking properly
• Error codes related to door lock issues displayed on the washer's control panel
• The cycle pausing or stopping mid-operation due to the door lock not functioning correctly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This inverter board controls the drive motor in front-load washers, converting household power into the precise variable speed and direction the drum needs. Replacing a failed board restores consistent tumbling and high-speed spin performance.

• Regulates drive motor speed and direction based on commands from the main control
• Converts AC line power to variable-frequency output for smooth starts and efficient spinning
• Monitors motor operation and shuts down on faults to prevent damage
• Typical failure symptoms: no spin or tumble, weak/intermittent motor operation, or motor/inverter error codes

• Disconnect power and turn off water supply; use ESD precautions and wear cut-resistant gloves
• Access the inverter module (often mounted low in the cabinet); remove any cover or bracket
• Transfer wire connectors one at a time to the new board; ensure all are fully seated and routed clear of moving parts
• Inspect the motor and wiring harness for shorts or damage before restoring power; run a spin-only or diagnostic test to verify operation

This main control board is the washer's central circuit module. It regulates cycle timing and coordinates key functions so your front-load machine fills, washes, drains, and spins as designed.

• Controls cycle timing and operation of the motor, drain pump, and water inlet valves
• Communicates with key sensors such as water level/pressure and the door lock
• Failure symptoms include no start, stopping mid-cycle, or no fill/drain/spin
• May trigger error codes or unresponsive controls depending on failure mode

• Disconnect power before servicing; electricity can cause injury
• Handle the board with ESD care; avoid touching components and contacts
• Transfer wire connectors one at a time; take photos to document routing
• Follow the included instructions to mount and configure the new board, then run a test cycle

The Gasket is an OEM part for GE dishwashers. It serves as the main seal between the tub and door, playing a critical role in preventing water leaks and maintaining moisture levels within the dishwasher. The material and design allow for a tight, durable seal during each wash cycle. 

Symptoms of a bad gasket include:

• Water leaks appearing around the base of the door or tub 
• Puddles or standing water inside the dishwasher
• Moisture indicators change color when the door is closed
• Inability to create or maintain proper pressure levels

Causes of failure can be cracks, tears, or wear developing from regular use and exposure to hot water and steam over time.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Water Valve is an OEM part for GE washing machines. As a key component located inside the washer cabinet, this valve precisely controls the flow of water into the machine during wash cycles. It allows for the filling of the tub with the proper amount of water at the correct temperature per the settings. 

Symptoms of a bad water valve include:

• Inability to fill the tub with water or fill levels being too low/high  
• Fluctuations in water temperature during fills
• Water leaks inside the washer cabinet or underneath
• Noisy sounds emitting from the water inlet area

Causes such as mineral buildup, worn internal seals and washers, or issues with the electronic interface and valve actuation mechanism over repeated use can all contribute to water valve failure.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Boot Gasket Clamp is an OEM part for GE washing machines. It secures the flexible boot gasket in the place where the washer connects to water supply lines. Proper installation with this clamp around the gasket helps prevent leaks at this critical water inlet point.

Causes of a bad boot gasket clamp include corrosion, cracks, or broken clips that no longer hold the gasket firmly in position. 

Symptoms of a bad clamp include:

• Water seeping or spraying from the boot connection area   
• Loose, slipping, or misaligned gasket that does not form a tight seal
• Rust or mineral buildup indicating long-term moisture exposure

This OEM GE replacement part is also compatible with some Hotpoint, RCA, and Kenmore models. 

The Motor is an OEM part for GE front-loading washing machines. It spins the wash basket during the wash and spin cycles. Whether gently tumbling fabrics or quickly extracting water from clothing, the motor works throughout the cleaning process.

Common causes involve bearing friction wearing down over extended use. Moisture infiltration can also potentially lead to electrical faults within the motor.

Symptoms of a faulty motor may include:

• Cessation of basket/drum movement during cycles
• Inability to activate specific cycles
• Noisy operation or abnormal vibrations
• Intermittent starting and stopping issues

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

The Inner Gasket Clamp is an OEM part for GE washing machines. It is responsible for securely holding the inner gasket in place, creating a tight seal between the tub and the door. This seal helps prevent leaks and contains water, lint, and debris during the wash and spin cycles. 

Symptoms of a bad inner gasket clamp can include:

• Water leaks around the door during operation  
• Excessive moisture buildup inside the door
• Deterioration or tearing of the inner gasket
• Difficulty closing or sealing the door properly

Causes of a bad clamp include damage from excessive Door popping or swinging open unexpectedly force or impact, wear and tear over time, or failure of the clamp components. 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Accelerometer (vibration sensor) that detects washer tub movement and sends signals to the control board so the machine can rebalance loads and reduce excessive shaking and noise during spin cycles. What it does:

• Measures tub/vibration movement and reports acceleration to the washer control board.
• Helps the machine detect and correct unbalanced loads during spin cycles.
• Common symptoms of a failing sensor: excessive shaking or banging during spin, interrupted or incomplete spin cycles, or unusual vibration/noise.
• Restoring accurate vibration sensing can reduce wear and improve spin stability.

• Disconnect power (and water, when applicable) before servicing to avoid shock or injury.
• Handle the sensor and connector carefully; secure the mounting and fully seat the electrical connector per the instructions.
• Verify routing and clearance so the sensor and wiring do not contact moving parts.
• After installation, run a test spin with a moderate load to confirm normal operation.

The Suspension Damper is an OEM component specifically designed for GE washing machines. This accessory helps stabilize the tub during high spin cycles.  

Causes of a bad suspension damper can include normal wear from absorbing vibrations spin cycle after spin cycle. Trapping of debris or mineral buildup may also impact damper operation over many years.

Symptoms of a bad suspension damper include:

• Excessive shaking, rattling or loud noises during spin  
• Premature wear of other suspension parts like the springs
• Potential tub or transmission damage from lack of control 

This GE replacement part is also compatible with Hotpoint, RCA and select Kenmore models as well. 

The Lock Bar is an OEM part for GE washers. It contains the locking latch mechanism that secures the washer lid tightly closed during operation. The durable lock bar construction ensures a dependable seal to contain water within the tub.  

Symptoms of a bad lock bar include:

• The lid failing to latch or unlock as expected  
• Gaps forming that allow water/air to pass under the lid
• Excessive play, wobble, or looseness of the locking mechanism
• Prying or extra force needed to open or close the lid 

Causes can be normal wear reducing smooth locking function, or issues such as a stripped screw hole compromising secure mounting.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. A properly functioning lock bar enhances safety by preventing the lid from opening until the cycle completes.

The DAMPER VENT is an OEM component specifically designed for GE washers. It is located within the vent system and is responsible for regulating airflow during spinning and draining cycles. The damper vent precisely controls the intake and expulsion of air, moisture, and odors for efficient drying performance. 

Causes of a bad damper vent can include lint or debris buildup that impedes movement, wear and tear of moving parts over time or damage to the vent or its attachment point. 

Symptoms of a bad damper vent include: 

• Excessive moisture remaining in the drum after cycles 
• Hampered air flow resulting in poor drying 
• Strange noises emanating from the vent area
• Dust or lint emitting from the vent instead of being expelled

Replace yours today with this genuine OEM GE part to ensure optimal moisture removal and ventilation. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dispenser Drawer is an OEM part for GE washers. This drawer holds and dispenses detergent, fabric softener, and other laundry additives during the washing cycle. The dispenser drawer ensures the proper distribution of laundry products in your GE washer. It features compartments and mechanisms that release the right amount of detergent and fabric softener at the appropriate times, ensuring cleaning and fabric care.

A bad dispenser drawer can occur due to wear and tear, clogging, or damage to the drawer or its components. If you notice symptoms such as improper dispensing, leaks, or difficulty in opening or closing the drawer, it may be time to replace it.

Symptoms of a bad dispenser drawer include:

• Improper dispensing of detergent or fabric softener
• Leaks or drips from the dispenser area
• Difficulty in opening or closing the drawer

Ensure efficient and hassle-free laundry cycles by replacing the faulty dispenser drawer with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This shipping bracket stabilizes a washer's internal components for safe transport. Install it before moving or returning the appliance to help prevent damage from vibration, shock, or shifting during shipment.

• Secures internal assemblies to reduce movement while the unit is in transit
• Helps protect the cabinet and internal parts from impact-related damage during moves
• Replace if the original bracket is missing, bent, or cannot be secured
• Remove and store the bracket before operating the washer

• Disconnect power and turn off water supply before installing any shipping hardware
• Follow your model's moving/transport instructions for exact placement and fastening
• Do not operate the washer with shipping hardware installed
• After transport, remove the bracket and verify leveling and connections before use

This door strike support mounts at the washer door area to hold the strike firmly in place. Keeping the strike aligned with the door lock ensures the door closes securely and the cycle can start reliably.

• Supports and positions the door strike for proper engagement with the door lock/latch
• Helps maintain door alignment and secure closure during operation
• Replace if cracked, broken, or threads are stripped

• Disconnect power before servicing
• Open the door and remove trim/screws as needed to access the strike and support; note orientation
• Attach the strike to the new support and reinstall using existing hardware; do not overtighten
• Verify the door closes and locks properly, then test with a short cycle