Range/Range/Oven Surface Element Board Parts

• No heat or not enough heat
• Doesn't shut off
• Touchpad does not respond

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

It took no time to find where the problem was! I got my Frigidaire model number and got on-line with AppliancePartsPros.com where I have gone for over a decade for all my household repairs. Why? because they are honest, helpful, considerate, fast, and its easy to locate and SEE the exact part I need. 10 minutes after the burning of my element, one was in my cart and ordered! Done. TWO days later, the part arrived. I turned off the circuit breaker, unscrewed the two 1/4" screws and pulled off... Read more

• No heat or not enough heat
• Takes too long to dry
• Too hot

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

I ordered the part I was sure I needed through the Appliance Pro website. I was surprised the part arrived in just two days. FIRST UNPLUG THE OVEN.. I removed the baking racks then two screws holding the plate over the element. I then removed three screws holding the old element in place, then gently wiggle/pull the element free from the electrical connections in the back of the oven. (Note: You cannot see the connections at this point. You'll need to remove the terminal block cover on the... Read more

Watched video. Took dryer apart to get to heating element and sensors. In process found alot of lint had escaped into inner dryer and had a thick coating over heating element. I cleaned out most lint and pulled apart lint trap on front and cleaned out as much accumulated lint as possible. I then removed the heating element (very simple, three screws in a support bracket) and found it was broke in one spot.(wire - element severed). I believe the heavy lint build up on elements caused lint to... Read more

• Not drying dishes properly
• Not cleaning dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

• Little to no heat when baking
• Oven is too hot
• Oven not heating evenly
• Won't start

Of course, these things always seem to happen on a holiday! Luckily we were not having guests for dinner - so quickly changed our eating plans for the evening. I went directly online and Googled "Bake elements for GE ovens". At first I did not think I would have luck finding this part because of the oven's age. AppliancePartsPros.com was one of the service dealers listed first and catered specifically to GE appliances and parts. So, I typed in the Model number and low and behold, a screen... Read more

I started with Google searches for the problem, using the dishwasher model number to narrow down the number of results. When I found several posts in the forum on AppliancePartsPros.com from other people having the same problem with the same dishwasher, as well as solutions that involved replacing the control board, I decided to start with that. The repair was very easy, especially with the help of clear and well-paced videos showing exactly what to do and what to look for. I was able to... Read more

First ran the built-in diagnostic tests. Got error code indicating that the inlet thermistor was open. Removed lower access panel and did continuity checks on the inlet thermistor, thermal cutoff and heating element. Even doing these checks is very difficult on this model due to the location of these parts and the limited access through the so-called access panel. But was able to get an open reading on the heating element, so I knew that at least that part was faulty. Could not get a reliable... Read more

Indicator light would blink three times, make a sound, but the dishwasher would not run. After making sure there were no obstructions, no problems with seals, filters, and latch clean, I cut the power off and back on. The Dishwasher worked for a few more times. After that, cutting the power off and on no longer worked. I figured out what buttons to press and hold to find the error code (start/stop and cycle select), saw code 815, and then did a "hard reset" by pressing and holding other... Read more

Visually inspected bottom heating element and found that it had failed. There was a @2" gap of missing element and burned debris below the damaged area. This was discovered 3 days before Christmas. 1. Open under oven storage drawer and look on the left inside frame frame for Model ID and Serial No. 2. Search on AppliancePartsPro.com for bottom heating element. 3. Ordered part on Sunday evening before Wednedsay Christmas - with expedited next day delivery. 4. Received order confirmation and... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start
• Element will not heat

Watched AppliancePartsPros.com instruction video. Ordered new oven bake element, which arrived a couple days later. Removed old oven bake elelment. Installed new oven bake element. I am very appreciative of the instructional video. It's a very handy way for me to figure out if it's a do-it-yourself repair or not. In this case, another key thing it pointed out was the fact that the two wires that attach to the oven bake element have a tendency to slip back into the insulation behind the... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start

It took a few of us. One to vacuum up the fire extinguisher residue. One to trip the breaker. One to provide light. One to clean out under the stove while it was pulled out. I disconnected the bake element. I needed help to disconnect one of them because it was very tight. I put the element into the oven and reconnected the right side, very easy. The left side fell back into the slot. Curses ensued. I removed the back plate and it was very easy to thread the left wire back into the oven and... Read more

• Too hot
• Takes too long to dry
• Doesn't shut off
• tripping breaker

This has been posted on my Facebook (but can't tag AppliancePartsPros) titled "As My Husband Slept!" =( Each dash represents a caption in each post. - Nice try taking a few days off! Your vacation days, or hours, are numbered ?? - Step 1: Removed 2 screws from the back. So far so good! - (after removing the top of the dryer) Wow! I'm so proud of myself ????? - (after the front panel was removed) Step 2: Remove the front panel as instructed by the guy on the video ?? ... I think I'm going to be... Read more

Two weeks ago, my dishwasher would not run. It would beep three times when you pushed the start button: the same signal it gives when the door is open. I used the troubleshooting steps I found at applianceblog.com to do a hard reset. (Hold START and WASH TEMP for five seconds, close the door, and wait 3 minutes) After that, it worked for about one week. When it started having the same issue again, the hard reset did not work. I lowered the control board and could see that there were no lights.... Read more

• Little to no heat when baking
• Oven not heating evenly
• Element will not heat

The first thing I did was call appliance pros. The tec told me it was a good chance it was the thermostat. He told how to test it with my ohm meter and what range it should be in. I pulled it out and tested it, which was out of the limits he told me it should be in. So I ordered the part. When it arrived in two days, I installed it. The oven now works perfect. Thank you so much. I was just about to go spend $800 on a new oven, and instead fixed it for $75. Awesome website. It was... Read more