Speed Queen Washer Parts

This dual water inlet valve kit controls the hot and cold water entering select top-load washers. Replacing a weak or leaking valve restores proper fill performance and helps prevent slow fills, wrong temperatures, and unwanted drips.

• Regulates hot and cold water flow into the tub during fill cycles
• Integrated inlet screens help trap debris from the water supply
• Failure can cause no fill, slow fill, incorrect temperature, continuous filling, or water seeping into the tub when off

• Disconnect power and turn off both water supplies before servicing
• Place towels and a container to catch residual water; relieve pressure at the hoses
• Note and transfer hose and wire connections one-for-one to the new valve
• Restore water and power, run a test fill, and check for leaks

This dual water inlet mixing valve controls and blends the hot and cold supply during the fill cycle. Replacing a failing valve restores proper fill rate and water temperature selection for consistent wash performance.

• Opens and closes to admit hot and cold water as directed by the control, creating the selected temperature
• Helps maintain proper flow to the tub/dispenser during fill
• Common failure symptoms: no fill or slow fill, incorrect water temperature during fill, water continuing to drip or flow into the tub when the machine is off, or leaks from the valve body
• Humming from the valve with little or no water flow due to internal failure or clogged screens

• Disconnect power and shut off both water supplies before servicing; relieve line pressure
• Place towels, disconnect hoses, and note hot/cold orientation; inspect/clean inlet screens
• Transfer any brackets/fittings from the old valve if required; connect hoses securely without overtightening
• Turn water back on, check for leaks, then run a fill test to verify operation

The Knob Assembly is an OEM component specifically designed for Speed Queen dryers. This assembly includes the control knob and integrated electronic components that allow for cycle and setting selection.

Causes of a defective knob assembly include normal wear of constantly rotated buttons, sun damage to exposed plastic knobs, and general use degradation of sealed electronic sensors over time. 

Symptoms of a bad knob assembly include:

• Knobs or buttons that do not select cycles properly   
• Faulty digital displays for time and settings
• Erroneous buzzers or error messages
• Unresponsive or stuck control functions

This OEM Speed Queen part is also compatible with products from American Dryer Corporation. Replacing the entire knob assembly restores full functionality to reliably control cycles on your dryer. Proper maintenance ensures long-term durability.
 

The Idler Lever Kit is an OEM replacement part for Speed Queen dryers. This kit includes the idler lever, which plays a key role in maintaining proper tension on the dryer drum belt. By ensuring the belt stays aligned and taut, the idler lever enables smooth drum rotation during the drying cycle.

Symptoms of a bad Idler Lever Kit include:

• A squealing or screeching noise during dryer operation
• The drum not spinning or rotating properly
• The belt appearing loose or slipping off the pulley

Causes of a failing Idler Lever Kit can include normal wear and tear over time, damage from excessive strain or overloading, or misalignment of the drum or belt.

This OEM Speed Queen part is also compatible with Alliance laundry equipment.

The Lid Lock Kit is an OEM part for Speed Queen washing machines. It is made up of lid lock components and mounting hardware that allow the washer lid to securely lock into place during operation.

Causes of a bad lid lock kit can include wear and tear over time, damage due to forced opening of the lid, or failure of the latching mechanism.

Symptoms of a bad lid lock kit include:

• The lid not latching securely during the cycle
• Difficulty or inability to open the lid
• Excessive vibrations or noises from an unlocked lid
• Potential safety issues if the lid inadvertently opens

The Drain Pump is an OEM part for Speedqueen brand washing machines. Located near the rear of the washer tub, the drain pump works to empty water from the machine at the end of each cycle. It functions through an electrical motor that activates a spinning impeller, forcing water through the drain hose. 

Symptoms of a bad drain pump include:

• Washer fails to fully drain or leaves standing water 
• Drain cycle takes an unusually long time to complete
• Loud grinding or rattling sounds coming from inside

Over time, a buildup of lint or mineral deposits inside the pump chamber can clog the impeller and reduce efficiency. Allowing water to sit for extended periods also promotes mold growth. Replace your drain pump today with this genuine Speedqueen part and restore full draining capability.
 

The Inner Door Bezel is an OEM replacement part for Speed Queen washing machines. It is a white plastic panel that mounts to the inside of the washer door providing structure and rigidity. The bezel acts as a backbone for attaching other door components like the door gasket, switches, insulation, and more.

Symptoms of a bad inner door bezel include:

• loose door components
• missing or damaged mounting tabs
• cracks along seams or corners
• uneven gaps around the door opening.

Causes of failure can be wear and tear from opening and closing the door thousands of times, exposure to cleaning chemicals or solvents over time, or physical damage from accidents.

The Pressure Sensor is an OEM part for Speedqueen commercial washers. It plays an important safety role by actively monitoring water levels and pressure changes within the washing machine. Located internally, the sensor communicates water level status to the control module.

Causes of a bad pressure sensor can include failure or degradation of electronic components over time. Damage from impact or liquid ingress may also cause sensors to malfunction.

Symptoms of a bad Pressure Sensor include:

• Erratic or inconsistent water levels during fills and drains
• Inability to detect rises or falls in water pressure
• Fault codes or error messages on the control panel
• Safety issues from unregulated water valves

This is a control knob for washing machines. This control knob is used to adjust the water temperature and level settings on the unit. It is manufactured out of a white plastic. The replacement is very easy and takes less than 15 minutes to complete. All that this process involves is pulling the old knob off and sliding the new knob on.A new control knob will be needed if the original is cracked, broken, or damaged in any way. Over time, the white plastic may begin to yellow, and the user may wish to replace the control knob for cosmetic purposes. If the knob is not actuating the desired cycle, it will need to be replaced.This control knob is a genuine SpeedQueen part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific control knob is compatible with washing machines that are manufactured by the SpeedQueen brand.

This pump assembly removes wash water from the tub and routes it to the household drain so the washer can complete drain and spin cycles reliably. Designed to restore proper water removal and reduce leak risk when the old pump fails. What it does:

• Forces wastewater out of the tub during drain cycles so the washer can advance to spin and finish cycles
• Helps prevent standing water in the drum that can cause odors or skipped cycles
• Can reduce abnormal noises caused by a failing or clogged pump
• Works with the washer's drain hose and plumbing to maintain proper flow

• One pump assembly

• Disconnect power and water before starting any repair
• Inspect and clear the drain hose and pump inlet before replacing the pump
• Expect basic panel and hose removal; keep screws and fasteners organized
• After installation, run a short drain/spin cycle to check for leaks and proper operation

The Lid Lock Catch Assembly is an OEM part for SpeedQueen washing machines. It is a mechanical component located on the washer lid that functions to securely latch and lock the lid shut during operation. 

Symptoms of a failing lid lock catch include: 

• The lid fails to lock firmly in place when closed
• Vibrations or movement of the lid during spinning cycles
• The inability of the washer to detect a closed lid and start cycles
• Buildup of lint or mineral deposits interfering with components

Causes of failure can be wear of moving parts over many uses, buildup that disrupts precise mechanisms, or impact damage affecting proper alignment and engagement. 

This OEM replacement is also compatible with Alliance, American, Continental, and some Kenmore models. 

This water inlet mixing valve controls and blends the hot and cold water entering your washer for proper fill temperature and water level. A worn valve can cause fill problems or unwanted leaks into the tub.

• Regulates hot and cold water flow to achieve the selected temperature
• Opens and closes electrically during fill cycles
• Common symptoms: slow fill, no fill, fills with only hot or only cold, or water seeping into the tub when the washer is off
• Electrical coil-operated design for reliable operation

• Unplug the washer and shut off both water supplies before servicing
• Place a towel or pan to catch residual water when disconnecting hoses
• Note hose positions (hot/cold) and wire connectors for correct reassembly
• After installation, check for leaks and run a test fill cycle

Note: DO NOT use any sealant other than 200996P Sealant.

This drain pump assembly removes wastewater from the tub during the drain and spin cycles, helping your washer empty quickly and complete cycles reliably. Replace a failing pump to fix standing water, aborted cycles, or drain-related error codes. What it does:

• Pumps water from the tub to the household drain during drain and spin
• Restores proper draining so cycles can finish as intended
• Common failure symptoms: no or slow draining, water left in tub, loud humming/grinding from the pump area, small leaks near the pump, or drain fault errors
• 100–127V, 60 Hz "yellow" variant per OEM specification

• One drain pump assembly

• Disconnect power and turn off water supply before servicing
• Expect residual water; place towels or a pan to catch spills
• Note hose and wire positions; transfer any mounting hardware from the old pump
• Inspect and clear the drain hose and tub-to-pump hose for blockages before testing for leaks

The Belt is an OEM part for Speedqueen washers. Transmits power between the motor and pulley system to turn the basket. Without a functioning belt, the washer will be unable to properly rotate the drum and agitate laundry during cycles.

Causes of a bad belt can include cracking, stretch wear or fatigue caused by age, prolonged use or excessive loads. Damage may also be due to slipping off pulleys.

Symptoms of a bad Belt include:

• Noise or squealing coming from the drive area
• The basket or agitator not spinning or turning slowly
• Motor overheating due to increased load from a slipping belt
• Belt slipping off or breaking completely

This timer knob assembly replaces a worn or broken control knob so you can confidently select and adjust cycles. A fresh knob restores a positive grip on the timer shaft and smooth, accurate operation.

• Mounts on the timer shaft to turn and set cycle selection and time
• Restores secure engagement when the original knob is cracked, stripped, loose, or missing
• Helps ensure the timer turns when you rotate the knob
• Common symptoms: knob spins without engaging, difficult to set cycles, visible damage

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft; avoid prying that could damage the control
• Align the new knob with the shaft (flat/D-shape) and press until fully seated
• If the original used a small insert or spring clip, transfer it to the new knob if needed