Parts for Lg LRBC20512TT / ATICLGG: Section 7 Parts

Secures the hinge to your refrigerator cabinet or door. Replace this bolt if stripped, missing, or corroded to restore proper door alignment and stability.

Replacement mounting screw for refrigerator assembly. Secures panels, brackets, or components. Needed when original screw is stripped, lost, or damaged.

The Screw is an OEM part for LG refrigerators. This part secures the shelf brackets within the refrigerator compartment.

Causes of a bad Screw can range from physical damage or impact to general wear and tear over time. 

Symptoms of a faulty Screw  include:

• Shelves feeling loose or unstable
• Shelves sagging or not sitting level
• Shelves falling out or collapsing when loaded with items

This OEM LG part is also compatible with some Kenmore models.

Replacement screw for refrigerators. Secures panels, brackets, and internal components. Install when original is missing, stripped, or damaged.

Replacement mounting screw for refrigerator interior components and panels. Needed when original hardware is stripped, lost, or damaged during repairs.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

Replace your refrigerator's rear handle if it's cracked, broken, or missing. This structural support handle mounts to the back panel of your unit.

Mounts inside your refrigerator to guide storage drawers for smooth opening and closing. Replace if cracked, broken, or worn to restore drawer alignment.

Fastener washer for refrigerators. Replaces worn, missing, or damaged washers that support screws and nuts. Restores proper spacing and load distribution.

Replaces a cracked or broken air duct assembly that routes cold air from the freezer to the refrigerator compartment. Mounts on the back wall of the fridge.

Rail guide assembly that supports and steers refrigerator drawers along their tracks. Replace if cracked, broken, or worn to restore smooth sliding.

Supports and guides refrigerator drawer for smooth sliding. Replace this rail guide if cracked, broken, or worn to restore proper drawer alignment and operation.

Ice spilling into the freezer? This refrigerator ice bin collects and stores ice cubes from your icemaker. Simple snap-in installation takes minutes.

Protective grille cover that shields the cooling fan and directs airflow in your refrigerator. Replace if cracked, broken, or missing to restore finish.

This shelf net is a mesh-style refrigerator shelf designed to support and contain food items while allowing airflow. It replaces torn, stretched, or missing nets to restore storage organization and help prevent items from shifting. What it does:

• Provides a flexible, ventilated surface for storing packaged foods, produce, or deli items
• Helps keep small or irregularly shaped items from falling through larger shelves
• Restores proper storage function when original netting is damaged, loose, or missing
• Compatible with designated shelf frames and snaps into place where equipped

• Unplug the appliance or turn off power to the unit before servicing for safety.
• Empty and remove food items from the affected shelf area before installation.
• Install by aligning the net with the shelf frame and securing per the owner's manual; do not force or modify parts.
• If installation requires removal of shelves or trim, keep fasteners and small parts organized and follow manufacturer instructions.

Replace your cracked or broken refrigerator glass shelf. This sturdy, easy-to-clean shelf restores lost storage space and keeps food organized.

Replacement shelf assembly for refrigerator interior storage. Installs inside refrigerator compartment. Needed when original shelf is cracked or broken.

Restore a broken or missing shelf with this refrigerator shelf assembly. It provides a sturdy, level surface for everyday storage, helping keep items organized and reducing spills or tipping in the fresh food compartment.

• Provides a stable, flat storage surface inside the refrigerator compartment
• Replace when the shelf surface or frame is cracked, chipped, bowed, or missing
• Helps keep items organized and maximizes usable space
• If the shelf won't sit level or falls from its supports, replacement is recommended

What's included: One refrigerator shelf assembly. Installation notes:

• Unplug the refrigerator and remove items from the shelf area before starting
• Lift out the old shelf carefully; handle any tempered surfaces with two hands and wear cut-resistant gloves
• Align the new shelf with the side rails/support tabs and slide it fully into place until level and secure
• Do not force the shelf; ensure all support points are properly seated

Replacement air vent shutter knob for refrigerator crisper drawers and shelves. Snaps onto vent lever for fingertip airflow control. Needed when broken or missing.

The Drawer Cover is an OEM part for LG refrigerators. It serves as a protective cover for the refrigerator's crisper drawers, providing a barrier that helps maintain optimal humidity levels and freshness for stored fruits and vegetables. The shelf measures approximately 19" in depth and 26" in width. This product does not include glass. As per the manufacturer's note, the original center support is not compatible with the updated crisper cover. 

You should replace the drawer cover if it becomes cracked, broken, or warped. Common causes of damage include placing heavy items on top of the cover, accidental impacts, or normal wear and tear over time, which can compromise its structural integrity and functionality.

Symptoms of a bad drawer cover include:

• Cracks or breaks in the cover
• The cover not fitting properly or sitting securely
• Difficulty in opening or closing the crisper drawers
• Reduced efficiency in maintaining the freshness of stored produce

This OEM LG part is also compatible with Sears/Kenmore models.

Protects and diffuses your refrigerator's interior light bulb. Replace when cracked, discolored, or missing to restore safe, even lighting. Confirm fit.

Protects and diffuses your refrigerator's interior light bulb. Replace when cracked, discolored, or missing to restore safe, even lighting. Confirm fit.

Refrigerator meat drawer tray assembly that holds deli items and fresh meat. Replace if cracked, broken, or missing to restore proper food storage.

Replaces a cracked, warped, or missing refrigerator door bin. Restores organized storage space for bottles and condiments in your door compartment.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Replace your refrigerator door gasket to restore the seal and maintain cooling efficiency. Fixes torn, cracked, or hardened seals that leak warm air.

Replace your cracked or broken refrigerator dairy door bin and tray. Installs in the door to organize butter, cheese, and small items. Essential replacement when original is damaged or missing.

Replace your refrigerator's dairy door tray cover if cracked, broken, or missing. This cover protects dairy items stored in the door compartment.

Please Note: The Sears/Kenmore parts diagram shows this part to be a 16 inch refrigerator door shelf. However, this piece is actually 8 inches in length. If you need the 16 inch shelf, you will need to order 5004JJ1028A.

Please Note: The Sears/Kenmore parts diagram shows this part to be a 8 inch refrigerator door shelf. However, this piece is actually 16 inches in length. If you need the 8 inch shelf, you will need to order 5004JJ1030A.

This is the door basket that mounts on the inner door to hold bottles, jars, and condiments. Replace a cracked or missing bin to restore secure, convenient storage and keep items organized on the refrigerator door.

• Attaches to the door liner to provide easy-access storage for small items
• Common failure signs: cracked plastic, broken mounting tabs, bin falls off, won't stay level, or missing bin
• Helps restore original storage layout and capacity
• Designed to fit the designated door slots for a solid, stable hold

What's included: One door basket/bin. Install notes:

• Compare the new bin to the original to confirm size and mounting points
• Empty contents; lift the old bin up and out of the door slots
• Align the new bin with the slots and lower until fully seated—do not force
• Distribute weight evenly and avoid overloading to prevent future damage

Plastic cap that snaps over refrigerator door handle ends to cover mounting screws and finish the handle. Replaces lost, cracked, or broken caps.

Secures water tubing to prevent leaks and disconnections in your refrigerator's water line system. Replace if clip is broken, missing, or tubing moves freely. Confirm fit with your model number.

Decorative plastic cap that covers the door hinge mechanism on top-mount refrigerators. Replaces cracked, broken, or missing hinge caps for a clean finish.

Plastic cap that covers and protects the refrigerator door hinge. Replace if cracked, broken, or missing to restore a finished look and shield the hinge.

Replacement door hinge bushing for refrigerators. Installs in door hinge mechanism. Replace when worn, cracked, or causing door grinding or misalignment.

Secures small moving parts and assemblies in refrigerators. Replace if the original pin is bent, broken, or missing to restore proper alignment.

Fridge not cooling or freezing? Compressor running constantly? This compressor set assembly restores cooling. Complex repair requiring professional tools.

Fridge not cooling or freezing? Compressor running constantly? This compressor set assembly restores cooling. Complex repair requiring professional tools.

Refrigerator clicking but not cooling? The compressor start relay kickstarts your compressor. Simple 30-minute DIY fix that gets your fridge cold again.

Refrigerator clicking but not cooling? The compressor start relay kickstarts your compressor. Simple 30-minute DIY fix that gets your fridge cold again.

Fix a refrigerator that hums and shuts down or won't start with this compressor overload protector. Simple DIY repair that restores safe operation.

Protective cover for your refrigerator's PTC and compressor start device assembly. Replace if cracked, melted, or missing to shield components from damage.

Rubber seat bumper for refrigerator shelves and drawers. Replaces worn, cracked, or missing rubber cushions that protect surfaces and reduce noise.

Refrigerator door stopper bumper that prevents door from overextending. Replace if cracked, broken, or missing to protect door hinges and cabinet.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

Fan guide for refrigerators. Directs airflow from the evaporator fan. Replace if cracked, broken, or missing to restore proper air circulation.

Fix ice buildup on evaporator coils or freezer not defrosting properly. This defrost thermostat monitors temperature to prevent frost. 2-hour repair.

Replacement damper motor support bumper for refrigerators. Secures the damper motor in position to maintain proper airflow. Replace if cracked or broken.

Interior light won't turn on when door opens? This refrigerator door switch signals when the door opens or closes. DIY-friendly repair, takes about 5 minutes.

Reflector lamp housing directs and diffuses interior bulb light for brighter refrigerator illumination. Replace if cracked, discolored, or missing.

The Light Bulb is an OEM part for LG refrigerators. It can be used in either the fresh food section or freezer compartment, providing illumination for easy visibility of the stored items.

Causes of a faulty light bulb can include regular wear and tear, reaching the end of its lifespan, or accidental breakage. These factors can result in issues such as a dark or poorly lit interior, making it difficult to see the contents of the refrigerator.

Symptoms of a bad light bulb may include:

• No illumination or dim lighting inside the refrigerator
• A flickering or intermittent light
• Visible damage or broken filament inside the bulb

This LG OEM bulb is also compatible with Sears/Kenmore models. 

The Light Bulb is an OEM part for LG refrigerators. It can be used in either the fresh food section or freezer compartment, providing illumination for easy visibility of the stored items.

Causes of a faulty light bulb can include regular wear and tear, reaching the end of its lifespan, or accidental breakage. These factors can result in issues such as a dark or poorly lit interior, making it difficult to see the contents of the refrigerator.

Symptoms of a bad light bulb may include:

• No illumination or dim lighting inside the refrigerator
• A flickering or intermittent light
• Visible damage or broken filament inside the bulb

This LG OEM bulb is also compatible with Sears/Kenmore models. 

Compressor humming but not starting? This start capacitor provides stable starting power to your refrigerator compressor. DIY-friendly repair.

This replacement lamp socket holds and powers the appliance light bulb, restoring clear, reliable illumination when the light is switched on. Replace a heat-damaged, cracked, or loose socket to stop flickering or a light that won't come on.

• Holds the bulb securely and supplies electrical power
• Restores consistent interior lighting for visibility
• Replaces sockets with heat damage, cracks, or worn contacts
• Symptoms: light stays off with a good bulb, flickers intermittently, or the bulb feels loose

• Disconnect power before servicing and allow the area to cool
• Remove the lens/cover and bulb; release the socket (tabs or screws) to remove
• Transfer wires one at a time to the new socket; ensure tight, correct connections
• Use only the bulb type and wattage specified for your model; test before reassembly

Refrigerator won't power on or loses power intermittently? This power cord assembly replaces frayed or damaged cords to restore safe, reliable operation.

Refrigerator running hot or not cooling? A failed condenser fan motor prevents heat removal from the compressor. DIY repair in under an hour.

Refrigerator not cooling or display settings going crazy? This control board assembly regulates temperature and defrost cycles. Moderate DIY repair.

Decorative control panel cover that installs over refrigerator user controls. Replace if cracked, faded, or damaged to restore finished appearance.

Outer housing cover for refrigerator control panel. Replaces cracked, damaged, or missing panel. Restores finished look and protects internal components.

The Case Assembly is an OEM part for LG side-by-side refrigerators housing electronic display modules. This assembly securely mounts LCD panels governing temperature readings and interface menus.

Causes of a bad case assembly can include moisture ingress degrading connections, stress fractures from repeated door openings, or impact damage compromising protective seals over time.

Symptoms of a bad case assembly include:

• Dimming or blank display lacking visibility 
• Unresponsive touch controls with miscalibrated inputs  
• Insecure mounting losing calibration on door
• Openings allowing corrosive vapors to damage electronics

Replace yours today with this genuine OEM LG assembly to safeguard refrigerator displays and customizable settings. Snap-fit clips produce a robust, water-tight seal around precision components. This replacement part is compatible with Kenmore, Samsung, and GE side-by-side models featuring similar interactive panels. Reliable mounting maximizes product life.

The Case Assembly is an OEM part for LG side-by-side refrigerators housing electronic display modules. This assembly securely mounts LCD panels governing temperature readings and interface menus.

Causes of a bad case assembly can include moisture ingress degrading connections, stress fractures from repeated door openings, or impact damage compromising protective seals over time.

Symptoms of a bad case assembly include:

• Dimming or blank display lacking visibility 
• Unresponsive touch controls with miscalibrated inputs  
• Insecure mounting losing calibration on door
• Openings allowing corrosive vapors to damage electronics

Replace yours today with this genuine OEM LG assembly to safeguard refrigerator displays and customizable settings. Snap-fit clips produce a robust, water-tight seal around precision components. This replacement part is compatible with Kenmore, Samsung, and GE side-by-side models featuring similar interactive panels. Reliable mounting maximizes product life.

Routing sleeve that supports and protects rods, shafts, or cables inside your refrigerator. Replace if cracked, broken, or missing to maintain alignment.

Replace a cracked, split, or leaking 1/4" water supply tube in your refrigerator. Connects household water line to dispenser and ice maker system.

Directs water from the valve to the ice maker fill cup. Replace this tube if it's cracked, blocked, or leaking to restore proper water flow to the mold.

No water dispensing or ice maker not working? This water inlet valve controls water flow to your refrigerator's dispenser and ice maker system.

No water dispensing or ice maker not working? This water inlet valve controls water flow to your refrigerator's dispenser and ice maker system.

Secures bracket assemblies inside your refrigerator to keep components aligned and reduce vibration. Replace if cracked, bent, or missing.

Secures internal components in place to prevent rattling and misalignment. Replace if cracked, broken, or missing. Confirm fit with your model number.

Front access panel that covers internal components at the base of your refrigerator. Replaces cracked, dented, or missing lower covers.

Secures the toe grille to the base of your refrigerator. Replace if broken, cracked, or missing to keep the lower kickplate panel firmly attached.

The Freezer Temperature Sensor is an OEM part for LG refrigerators. This sensor monitors the temperature within the freezer compartment, sending readings to the refrigerator’s control board to maintain optimal temperature levels. It plays a crucial role in ensuring that the freezer operates efficiently and keeps food items properly frozen.

Over time, the temperature sensor can fail due to regular wear and tear, electrical issues, or exposure to extreme temperatures. A faulty sensor can lead to inaccurate temperature readings, affecting the freezer's performance.

Symptoms of a bad freezer temperature sensor include:

• Inconsistent freezer temperatures
• The freezer running continuously or not running at all
• Frost buildup in the freezer compartment
• The control board displaying error codes related to temperature

This OEM LG part is also compatible with Sears/Kenmore.