Parts for Ikea 90462157B: Shelves Parts

This refrigerator water tube carries fresh water between the valve, reservoir, dispenser, and/or ice maker. Replacing a cracked or kinked tube restores proper water flow and helps stop leaks inside or behind the refrigerator.

• Directs pressurized water between components in the refrigerator's water system
• Common failure signs: leaks, visible cracking, kinks, or pinhole sprays
• May cause no or slow dispenser flow, or an ice maker that doesn't fill
• Restores correct routing after tubing becomes brittle or damaged with age

• Unplug the refrigerator and shut off the household water supply before servicing
• Place a towel under connections and dispense water to relieve line pressure
• Depress quick-connect collars or loosen clamps to remove the old tube; route the new tube exactly like the original
• Fully seat tubing in fittings, perform a gentle tug test, restore water, check for leaks, and flush several cups to clear air

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This buffer is a small door-stop cushion that dampens contact and helps the appliance door close quietly and securely. It restores proper door cushioning to reduce noise and prevent hard impacts. What it does:

• Cushions the door at the stop point to reduce slamming and rattling
• Prevents metal-on-metal contact that can cause wear or chipping
• Helps the door seat more evenly for improved seal performance
• Common symptom: loud clunk, vibration, or visible door contact at the stop

• Disconnect power before working on the appliance to avoid electrical hazard
• Typically pushes or snaps into a mounting post; may require removing the door trim or gasket for access
• Inspect surrounding mounting area for damage and replace mounting clips if worn

The Crisper Drawer Cover is an OEM part for Frigidaire refrigerators. This component acts as a shelf while also covering the crisper drawers where fruits and vegetables are stored. It's designed to support weight and maintain an optimal environment in the crisper drawers by helping to regulate humidity and temperature. 

Over time, the Crisper Drawer Cover can become cracked, warped, or damaged due to excessive weight, accidental impacts, or temperature fluctuations. Such damage can compromise its structural integrity and functionality, leading to potential issues with drawer alignment or difficulty in sliding drawers in and out.

Symptoms of a bad Crisper Drawer Cover include:

• Visible cracks or stress marks that can weaken the cover's structure.
• Warping or bending, which can interfere with the smooth operation of the crisper drawers.
• Difficulty in maintaining consistent humidity levels within the drawers

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This cover is the replacement access panel that protects internal components and finishes the appliance's exterior for a clean, secure appearance. It restores proper enclosure and helps prevent dust, moisture, and accidental contact. What it does:

• Covers and protects internal parts, wiring, and connections from debris and damage
• Helps maintain the appliance's finished appearance and prevents gaps
• Keeps serviceable components secure and reduces the chance of accidental contact
• A damaged or missing cover can cause rattling, drafts, or visible gaps

• Always disconnect power (unplug or switch off circuit) before installing
• Use basic hand tools to remove fasteners, carefully lift out the old cover, and align mounting tabs
• Handle edges carefully to avoid cuts or cosmetic damage; avoid forcing tabs to prevent breakage
• If mounting hardware is damaged or missing, replace with matching screws or clips for a secure fit

The Crisper Pan is an OEM part for Frigidaire refrigerators featuring interior crisper drawers. It functions as a durable liner tray optimized to maintain proper humidity levels for storing fruits and vegetables. 

Symptoms of needing replacement include:

• Excessive cracking, pitting or peeling of surfaces   
• Sharp edges or broken corners become a hazard
• Difficulty fitting properly or staying securely in a drawer
• Inability to retain moisture or prevent drying out of foods

Causes can include heavy usage wear over time, being damaged during cleaning, or warping from extended high-humidity environments. 

This genuine OEM crisper pan is compatible with Electrolux, Gibson, Kelvinator, and Kenmore fridge models. 

The Shelf Rail is an OEM replacement part for Frigidaire top-freezer refrigerators. These durable epoxy-coated rails allow shelves to smoothly slide in and out of the refrigerator. 

Causes of bad shelf rails can include dents, scratches, or damage to the coated finish from years of shelves being inserted and removed. The chrome coating prevents corrosion but is susceptible to wear over time.

Symptoms of faulty shelf rails include:

• Shelves that do not easily glide or are difficult to remove
• Excessive sticking or binding during extension  
• Gouges or bends in the rail surfaces

This OEM Frigidaire part is also compatible with Electrolux, Gibson, and some Kenmore top-mount fridge models.

The Frigidaire Left Side Support Rail is an OEM Replacement Part designed for use in refrigerators. This genuine part functions to align drawers and shelves within the refrigerator. It provides ease of movement and maintains level positioning. It's essential to ensure the number of shelf rails required as there are typically many ones present in a single appliance.

Over time, shelf rails can experience damage. Damages such as denting, cracking, bending, or breaking, affect the levelness and balance of shelves and drawers. If such issues are observed, a new support rail is recommended to restore the appliance's functionality. Installation is straightforward but requires access to the refrigerator's interior. This OEM part is sourced directly from the manufacturer, ensuring compatibility with Frigidaire refrigerators.

This shelf channel is the metal/plastic support that secures and aligns a refrigerator shelf or door bin, helping keep stored items stable and properly positioned. It restores proper shelf fit and prevents sagging or misalignment. What it does:

• Provides a secure mounting track for a refrigerator shelf or door bin
• Supports shelf weight to prevent bowing, shifting, or falling
• Keeps the shelf aligned so items sit level and doors close smoothly
• Helps restore original shelf fit after damage or wear

• One shelf channel mounting piece

• High-level replacement; inspect adjacent clips and fasteners and replace if damaged
• Use proper hand tools; avoid overtightening to prevent cracking
• Disconnect power only if working near electrical components; otherwise power removal is not typically required

This shelf channel is the replacement mounting rail that supports and secures a refrigerator shelf, restoring stable shelf alignment and load support. Use it when a shelf slides out of position or the mounting rail is cracked or bent. What it does:

• Provides the mounting surface and guide for a refrigerator glass or wire shelf
• Restores proper shelf alignment and prevents sagging or uneven seating
• Replaces damaged, cracked or bent shelf rails that allow shelves to shift
• Helps maintain safe storage by keeping shelves locked in place during use

• Basic hand tools required; follow the refrigerator's service diagram for exact removal and replacement steps
• Support the shelf when removing the old channel to avoid dropping or damaging the shelf
• Disconnect power (or unplug) the appliance if working near electrical components or lighting
• Replace any fasteners, clips or adjacent trim that are damaged to ensure proper fit and secure mounting

This shelf channel secures and supports a refrigerator shelf, restoring proper shelf alignment and weight distribution. It fits at the shelf edge to keep glass or wire shelves seated and stable. What it does

• Replaces a bent, cracked, or broken shelf channel that prevents a shelf from seating correctly
• Restores proper shelf support to stop shelves from tilting or sagging under load
• Provides the mounting surface that holds the shelf in place when sliding or repositioning
• Helps eliminate shelf movement and rattling caused by a damaged channel

• Disconnect power to the appliance before starting work and remove stored items from the shelf area
• Remove the shelf and any retaining clips to access the channel; reinstall in reverse order
• Align the channel with factory mounting points; secure with the original hardware or OEM replacement fasteners

This shelf channel mounting bracket secures the shelf channel to the appliance cabinet so shelves stay level and stable. It replaces a broken or worn mount to restore proper shelf alignment and support. What it does

• Secures the shelf channel to the cabinet frame so shelves sit flush and don't tilt.
• Prevents shelf movement or sagging caused by a loose or cracked mount.
• Helps maintain safe storage by keeping items from sliding off tilted shelves.
• Fits where the original channel mount has cracked, worn, or snapped.

• Designed for simple replacement—remove the shelf and channel to access the mounting bracket.
• Use appropriate hand tools; avoid over-tightening fasteners which can crack plastic components.
• Disconnect power and remove stored items from the shelf area before beginning work.
• If mounting locations are damaged, assess surrounding supports; replace any additional broken hardware.

This slide replaces a worn or broken drawer support to restore smooth, stable drawer movement and secure shelf alignment. Durable replacement designed to match the OEM fit and function for proper drawer operation. What it does:

• Supports and guides a refrigerator/freezer drawer or shelf for smooth in-and-out motion
• Restores proper alignment when drawers stick, drag, or sit unevenly
• Prevents drawers from falling out or binding during use
• Reduces noise caused by worn or damaged sliding tracks

• Always unplug the appliance or switch off power before servicing to avoid electrical hazard
• Remove the drawer or shelf to access mounting screws and clips before replacing the slide
• Compare the new slide to the original to ensure correct orientation and fastener locations
• Use common hand tools; do not force parts—if mounting holes don't line up, stop and verify part compatibility

This replacement deli drawer pan is for the fresh food compartment. It restores a smooth-sliding, dedicated space for meats and cheeses so the refrigerator stays organized and the drawer sits correctly on its tracks. What it does:

• Provides a dedicated bin for deli meats and cheeses in the fresh food section
• Seats on existing tracks under the shelf to slide in and out smoothly when undamaged
• Replacing a cracked, broken, or missing bin restores proper fit and containment
• Common symptoms: drawer cracked, won't stay on rails, difficult to slide, or missing

• Disconnect power and remove food from the area before servicing
• Pull the old drawer straight out and lift to clear the rails; align the new pan and slide it fully onto both tracks
• Handle the pan carefully—avoid flexing or forcing the plastic
• Remove the shelf above to gain clearance

Color: Black/natural. Nylon

The Water Filter Bypass is an OEM replacement part for Frigidaire refrigerators. It provides an alternative water supply route to bypass the refrigerator's built-in water filtration system. The bypass allows refrigerator water and ice dispensers to operate without water flowing through the installed filter cartridge. 

Causes of a malfunctioning bypass can include mineral buildup inhibiting proper operation of the bypass valve, worn seals or O-rings not providing a tight seal or physical damage.  

Symptoms include:

• Inability to bypass the water filter when needed  
• Leaks from the bypass area
• The filter bypass not functioning or engaging properly

This OEM replacement is also compatible with refrigerator brands like Electrolux, Gibson, Kelvinator, and select Kenmore models.

The Frigidaire PureSource Ultra II Refrigerator Water & Ice Filter is an OEM part for Frigidaire refrigerators provides clean, fresh-tasting water and ice. This advanced filtration system is specifically engineered to remove impurities and contaminants from your water supply, including lead, chlorine, mercury, and certain pesticides, without removing beneficial fluoride. 

Regular replacement of the water and ice filter is crucial for maintaining the quality of your drinking water and the efficiency of your refrigerator's water and ice dispensing system. Over time, filters can become saturated with contaminants, reducing their effectiveness and potentially impacting the taste and safety of your water.

Symptoms of a filter in need of replacement include:

• Reduced water flow from the dispenser
• Unpleasant taste or odor in the water and ice
• The refrigerator's water filter indicator light turning on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This support is a small mounting bracket that secures internal components and helps stabilize appliance assemblies for quieter, more reliable operation. It's a direct-fit replacement when the original support is cracked, bent, or worn. What it does:

• Holds and positions internal parts so they stay aligned during normal use
• Reduces movement that can cause rattling or uneven operation
• Restores proper clearances to prevent wear on adjoining components
• Helps maintain cabinet and assembly stability after damage or deterioration

• One support mounting bracket as shown

• Disconnect power before servicing the appliance to avoid shock or injury
• Remove panels or coverings as needed to access the damaged support; a basic set of hand tools is usually required
• Inspect surrounding fasteners and mating parts; replace any worn hardware for a secure fit

This support is a small mounting bracket used to secure internal components and keep parts aligned for reliable operation. It replaces a worn or broken support to restore proper fit and reduce movement or rattling. What it does:

• Secures and supports internal appliance components to maintain correct alignment
• Prevents shifting that can cause noise, wear, or poor operation
• Fits into the appliance's support/mounting location shown in OEM diagrams
• Used when the original support is cracked, bent, or missing

• Disconnect power to the appliance before starting any repair
• Basic hand tools are typically required;
• Handle carefully to avoid damaging nearby components or trim

This genuine replacement screw restores a secure hold for panels, trim, or internal components. It replaces worn or missing fasteners so parts stay aligned and appliances operate safely. What it does:

• Fastens panels, brackets, or trim into place
• Replaces stripped, missing, or damaged screws
• Helps stop rattling, loose panels, or misaligned trim
• Fits OEM mounting locations that require the specified machine screw

• Use the correct driver to avoid stripping the head
• Hand-start the screw, then tighten to firm snug; do not over-torque
• Disconnect power to the appliance before accessing internal components
• If other fasteners are damaged, inspect and replace as needed

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

This is a replacement electrical plug used to reconnect a wiring harness to an appliance component, restoring a secure electrical connection and helping stop intermittent power loss or component failure. What it does:

• Provides a secure electrical connection between wiring and the appliance component
• Replaces a cracked, burned, or loose plug that can cause intermittent operation
• Helps restore power to the affected component when failure is due to a faulty connector
• Prevents arcing or poor contact that can lead to overheating or component malfunction

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle wiring and terminals carefully; do not force connectors into place
• If wiring or terminals are damaged, repair or replace them rather than relying solely on a new plug

The Crisper Pan Roller is an OEM replacement part for Frigidaire side-by-side refrigerators. Located in drawer tracks below crisper bins, these rollers facilitate smooth extension and retraction of crisper pans.

Symptoms of damaged crisper pan rollers include: 

• Difficulty fully withdrawing or pushing in crisper pans  
• Jumpy or uneven movement of pans on drawer slides
• Visible scratches or flattened spots on roller surfaces  
• Creaking or grinding noises emanating from drawer area

Causes relate to repeated weight impacts over years absorbing crisper loads containing vegetables and fruits. Rust accelerates on rollers exposed to humidity fluctuations inside drawers.

This pan roller is compatible with select Electrolux and Kelvinator models as well.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This replacement screw secures appliance components to their mounting points so panels, brackets, and trim stay tight and aligned. Replace missing or stripped hardware to restore a solid, rattle-free fit and proper assembly integrity.

• Secures panels, brackets, and trim to prevent movement and maintain alignment
• Replaces missing, damaged, or stripped hardware that can compromise assembly
• Helps reduce rattling or vibration from loose components
• Restores proper fit after service or access panel removal

• Unplug the appliance before servicing; turn off water supply if working near dispenser/ice areas
• Compare the new screw to the original to ensure thread, head style, and length
• Start threading by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Retain and reuse any original washers, spacers, or clips as required