Parts for Ikea 90462157B: Cabinet Parts

This replacement access cover protects internal components and restores the appliance's finished appearance. It helps keep dust and debris out while securing wiring and mounting points for nearby parts. What it does:

• Shields internal components from dust, spills, and accidental contact
• Helps keep wiring and connectors in place and prevents snagging
• Restores a clean, finished appearance when the original cover is cracked or missing
• Reduces rattling or vibration caused by a loose or broken panel

• Disconnect power to the appliance before beginning any work
• Remove fasteners holding the old cover; save screws if they remain undamaged
• Align cover over mounting points and reinstall screws; do not overtighten
• If you encounter hidden clips or wiring, proceed slowly to avoid damage

This replacement door gasket seals the freezer compartment to help keep cold air in and warm air out, improving temperature stability and energy efficiency. It restores a tight seal for effective cooling and frost control. What it does:

• Creates an airtight seal around the freezer door to prevent cold air loss
• Helps reduce frost buildup and maintain consistent internal temperatures
• Can improve cooling performance and reduce run time from air leaks
• Common symptoms: visible gaps, torn or deformed gasket, frost buildup, or higher-than-normal appliance run time

• Remove the old gasket and clean mounting surface of dirt and old adhesive before installing
• Start at one corner, align the gasket, and press into the door channel evenly for a full seal
• Some gaskets seat better after a short warm water soak or gentle stretching—follow OEM guidance
• If magnets or mounting clips are present, confirm they are engaged.

The Evaporator Fan Blade is an OEM part for Frigidaire refrigerators, designed to circulate air over the refrigerator coils and through the food compartment. The fan blade works in conjunction with the evaporator fan motor, and together, they play a key role in the cooling process by distributing cool air evenly throughout the refrigerator and freezer.

Causes of a bad evaporator fan blade can include physical damage, such as cracks or bends in the blade itself, which can occur over time due to wear and tear or during cleaning and maintenance. 

Symptoms of a bad Evaporator Fan Blade include:

• Unusual noises coming from the refrigerator, such as humming or buzzing
• The refrigerator or freezer compartment is not cooling adequately

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Motor Mount Bushing is an essential OEM component inside Frigidaire bottom-mount refrigerators. It secures the evaporator fan motor securely while cushioning vibrations transmitted to the refrigerator body.  

Causes of failure include natural wear of plastic glide surfaces from prolonged absorption of mechanical stresses during compressor and fan operation cycles. Deformations compromise uniform motor positioning over time.

Symptoms of a worn motor mount bushing include:

• Rattling noises emanating from the refrigerator fan area
• Reduced air circulation leading to warmer interior temperatures 
• Lubricant leaks at the mounting point requiring replacement

This authentic OEM replacement is compatible with Frigidaire, Electrolux and select Kenmore models.

This replacement coil-cover gasket seals the refrigerator coil/cover area to help maintain proper airflow and reduce dust buildup around the condenser/evaporator cover. Restores the intended fit and helps maintain cooling efficiency. What it does:

• Seals the gap between the coil cover and cabinet to direct airflow over coils
• Helps prevent dust, debris and pet hair from collecting on coils
• Reduces vibration noise by cushioning the cover edge
• Commonly replaced when the gasket is torn, flattened, or missing, or when air leaks are noticed

• Inspect mating surfaces and remove old adhesive/residue before installing for a secure seal
• Use appropriate adhesive or clips if required by your model; follow OEM instructions
• Disconnect power to the appliance before servicing and avoid sharp edges on sheet metal

The Air Tower is an OEM part for Frigidaire refrigerators. It is responsible for distributing cold air throughout the refrigerator compartment.

A bad air tower can be caused by blockages, damage, or wear and tear over time. Signs of a faulty assembly include improper cooling, uneven temperature distribution, or frost buildup.

Symptoms of a bad air tower include:

• Inconsistent cooling 
• Frost accumulation 
• Poor temperature regulation

Replace your damaged or malfunctioning air tower with this genuine OEM Frigidaire part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This evap coil cover protects the evaporator and helps direct airflow for more consistent cooling. It replaces damaged or missing covers to reduce frost buildup, keep debris away from the coil, and help prevent interior leaks. What it does:

• Shields the evaporator coil from ice, debris and accidental contact to protect coil fins.
• Helps channel airflow across the coil for improved cooling performance.
• Can reduce frost accumulation and related moisture or dripping symptoms.
• When cracked or missing, you may notice increased frost, water in the cabinet, or reduced cooling.

• Always disconnect power to the appliance before servicing.
• Remove interior liners or access panels to reach the evaporator; handle coil fins and insulation carefully.
• Reinstall any mounting clips, grommets, or insulation exactly as removed to maintain fit and sealing.

The Evaporator Fan Motor is an OEM part for Frigidaire refrigerators. It circulates air over the evaporator coils and throughout the refrigerator and freezer compartments, ensuring even cooling and maintaining the desired temperatures.

Causes of a bad evaporator fan motor can include general wear and tear over time, electrical failures such as shorts or blown fuses, or physical damage from ice buildup or debris.

Symptoms of a bad evaporator fan motor include:

• Refrigerator or freezer not cooling properly
• Unusual noises coming from the freezer compartment
• Frost buildup on the evaporator coils
• Inconsistent temperatures within the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door-activated light switch installs in the refrigerator liner and opens or closes the circuit to the interior lamp as the door moves. It restores reliable, automatic on/off lighting when you open and close the door. What it does:

• Controls the interior light based on door position
• Helps fix a light that won't turn on with the door open
• Helps fix a light that stays on when the door is closed
• On some models, also signals door-ajar/dispenser interlock functions

• 1 light/lamp switch

• Disconnect power to the refrigerator before servicing
• The switch is typically in the door jamb; gently release and pull it out, then transfer wires one at a time to the new switch
• Match wire positions/orientation and seat the switch flush to prevent air leaks
• Test door operation and light before finalizing reassembly

This LED interior light assembly provides bright, long-lasting illumination for the refrigerator compartment so you can see contents clearly. Designed to replace a dim, flickering, or non-working interior light. What it does:

• Replaces a failed or flickering refrigerator interior light to restore visibility
• Provides cool-running LED illumination with immediate full brightness
• Fits into the refrigerator light housing and connects to the factory wiring
• Helps you locate items quickly and reduces the need to keep the door open

• One LED light assembly

• Disconnect power to the appliance before installing to avoid shock hazard
• Remove the existing lens/cover and unplug the old light assembly from its connector
• Plug in the new assembly, secure the lens/cover, and restore power to test

The Air Duct Seal is an OEM replacement part for Frigidaire refrigerators. It is a rubberized seal that creates an airtight connection between the refrigerator ductwork and internal fans/vents. This seal works to carefully direct chilled air to optimize freshness preservation in different fridge zones.

Causes of a bad air duct seal can include degradation over time from constant vibration and temperature fluctuations inside the fridge walls. 

Symptoms of a bad air duct seal include:

• audible leaks or whistling noises originating from duct areas
• inadequate air circulation causing temperature variations  
• buildup of frost or moisture near improperly sealed ducts

Replace with this genuine OEM seal to restore balanced air control for fresher stored foods. It fits refrigerator models also compatible with Electrolux, Gibson, Kelvinator, and Kenmore designs.

This is a replacement screw fastener used to secure panels, trim, or components on compatible Frigidaire appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or trim pieces to keep components aligned and stable
• Prevents rattling, vibration noise, and gaps caused by missing or loose fasteners
• Restores proper assembly after service or part replacement
• Helps maintain safety by keeping covers and guards firmly attached

• One screw (single fastener)

• Disconnect power or unplug the appliance before servicing
• Use the appropriate driver to avoid stripping the head; do not overtighten
• Verify the screw matches the original in length and thread before installing

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures select refrigerator door handles to the door. A worn or missing screw can leave the handle loose or detached, making the door difficult to open and potentially stressing other components.

• Holds the door handle firmly to the door
• Helps restore proper door operation and safe grip
• Designed to fit designated mounting points for compatible models

• Unplug the refrigerator before beginning work
• Open the door to access the handle mounting points
• Use the correct screwdriver/Allen tool to avoid stripping the head
• Start threads by hand and tighten snugly—do not overtighten

This anti-tip bracket secures the front of a freestanding range or oven to help prevent the appliance from tipping forward when the door is open. It provides a simple safety anchor that reduces tip-over risk and improves stability. What it does:

• Anchors the range to the floor or wall framing to resist forward tipping when the oven door is opened.
• Helps prevent appliance movement during normal use or when cookware is on the door.
• Addresses signs of a loose or shifting range: visible forward tilt, rocking at the front, or uneven gap between appliance and cabinetry.
• Works with the range's leveling and anti-tip system to maintain stable operation.

• One anti-tip bracket

• Install bracket to solid floor or wall framing per the appliance installation instructions; follow exact mounting locations and fastener types recommended by the manufacturer.
• Level the appliance and verify engagement with the bracket after sliding the range into place.
• Use appropriate fasteners for your floor/wall material.
• Disconnect power to the appliance before working in tight areas and follow all safety guidance in the owner's manual.

The Hinge Assembly is an OEM replacement part for Frigidaire refrigerators. It is the mechanism that allows the refrigerator doors to open and close properly. The hinge assembly consists of metal brackets, pins, and bushings that connect each door to the fridge cabinet and facilitate smooth swinging movement. 

Causes of a bad hinge assembly can include wear from years of operation, excessive weight on door racks damaging components, or damage if the refrigerator is moved improperly.  

Symptoms of a bad hinge assembly include:

• Doors that do not close or align securely  
• Gaps that compromise the refrigerator seal 
• Noisy or rough door movement
• Doors difficult to open, especially when full or heavy

As a major moving component, hinges can degrade over time. Replace with this genuine OEM part to restore proper door function for Frigidaire refrigerators. It fits models also compatible with Electrolux, Gibson, Kelvinator, and Kenmore designs.

The Hinge Assembly is an OEM replacement part for Frigidaire refrigerators. It is the mechanism that allows the refrigerator doors to open and close properly. The hinge assembly consists of metal brackets, pins, and bushings that connect each door to the fridge cabinet and facilitate smooth swinging movement. 

Causes of a bad hinge assembly can include wear from years of operation, excessive weight on door racks damaging components, or damage if the refrigerator is moved improperly.  

Symptoms of a bad hinge assembly include:

• Doors that do not close or align securely  
• Gaps that compromise the refrigerator seal 
• Noisy or rough door movement
• Doors difficult to open, especially when full or heavy

As a major moving component, hinges can degrade over time. Replace with this genuine OEM part to restore proper door function for Frigidaire refrigerators. It fits models also compatible with Electrolux, Gibson, Kelvinator, and Kenmore designs.

This refrigerator bracket is the OEM mounting piece that secures a specific internal assembly in place. Replacing a cracked or missing bracket restores a solid fit, proper alignment, and smooth, rattle-free operation of the attached component.

• Provides a rigid mounting point for the designated refrigerator component
• Maintains proper alignment to help the assembly operate correctly
• Helps reduce vibration and movement that can cause noise or wear
• Typical signs of failure: broken tabs, stripped holes, loose or misaligned parts

• Disconnect power; turn off water supply if working near ice/water components
• Access the area per your product's diagram; retain and reuse existing screws/fasteners
• Transfer any clips, spacers, or grommets from the old bracket to the new one
• The mounted component seats fully and operates before reassembling panels/shelves

This hinge bracket supports and aligns the refrigerator door at the pivot point, helping the door open and close smoothly and seal properly. Replacing a worn bracket can restore stable door movement and reduce air leaks.

• Provides rigid support for the door hinge to maintain proper alignment
• Helps ensure a consistent door seal to prevent temperature fluctuations
• Common fix for loose, sagging, or misaligned doors
• Helps if the door makes popping/grinding noises when opening or closing

• Unplug the refrigerator and wear cut-resistant gloves
• Support the door before removing hinge fasteners to prevent drops
• Transfer and reinstall existing screws/hinge pin as needed
• Check door alignment and gasket contact after installation

This cover is a replacement trim piece that restores the appliance's appearance and protects internal components from dust and debris. It fits into the appliance's exterior to keep controls and openings concealed and neat. What it does

• Covers and protects exposed openings or components to help prevent dirt buildup and accidental contact.
• Restores a finished, factory appearance where the original cover was cracked, warped, or missing.
• Helps maintain proper airflow and component alignment when installed as intended.
• Reduces the chance of small objects entering internal compartments.

• One replacement cover trim piece as shown.

• Disconnect power to the appliance before removing panels or replacing parts to reduce risk of shock.
• Remove only the fasteners or clips securing the damaged cover; save hardware if the replacement does not include new fasteners.
• Handle the cover carefully to avoid scratching or damaging finish during installation.

This upper hinge cover protects and finishes the refrigerator door hinge area for a clean appearance and helps keep the hinge mechanism free from dust and debris. It's a direct-fit replacement that restores the original look. What it does:

• Covers the upper door hinge to conceal hardware and provide a finished appearance
• Helps limit dust and debris from collecting on the hinge mechanism
• Restores worn, cracked, or missing hinge trim for improved cosmetic condition
• Fits and aligns with the existing upper hinge assembly for a neat, factory look

• One upper hinge cover

• Disconnect power to the appliance and support the door before removing hinge parts
• Remove necessary trim or screws from the hinge area to access and replace the cover
• Handle plastic trim carefully to avoid cracking; use appropriate hand tools
• Reassemble hardware securely and verify door alignment before returning the appliance to service

This upper hinge cover is a molded plastic trim piece that protects and conceals the refrigerator door hinge assembly while keeping the cabinet opening neat. It restores the finished appearance and helps prevent dirt buildup around the hinge. What it does:

• Covers and protects the upper door hinge area from dust, debris, and incidental contact
• Conceals hinge hardware for a clean, factory appearance
• Replace if cracked, broken, missing, or if the hinge area looks exposed or unsightly
• Matches OEM fit and shape to maintain proper clearance around the hinge

• High-level: installation typically requires removing or supporting the door; follow the appliance manufacturer's service instructions
• Use basic hand tools; take care not to damage surrounding trim or paint
• Always disconnect power to models with connected electronics before doing service that could affect wiring

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

The Board Assembly is an OEM replacement part for Frigidaire refrigerators. It contains the network of electronic components that control all cooling functions such as temperature regulation, defrost operations, and power distribution. 

Causes of a bad board assembly include normal wear of integrated circuits and capacitors from prolonged use of the cooling system. Infrequent cleaning may also allow dust buildup, inhibiting heat dissipation and accelerating component fatigue.

Symptoms of a faulty board include:

• Difficulty maintaining set interior temperatures    
• Inoperable control buttons and display interfaces
• Failure to automatically defrost or enter cooling cycles
• Premature shutting off or error code messages  

This OEM part is compatible with Electrolux, Gibson, Kelvinator and select Kenmore models.

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: Grey

Hex washer head ,10-32 x 0.375. Ground

The Temperature Sensor (10K NTC) is an OEM replacement part for Frigidaire refrigerators. This sensor monitors the internal temperature of the refrigerator or freezer compartment, sending signals to the control board to regulate cooling cycles. It ensures the appliance maintains the correct temperature for optimal food preservation.

Temperature sensors can fail due to wear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can cause inaccurate temperature readings, leading to improper cooling or freezing.

Symptoms of a bad temperature sensor include:

• Fluctuating or incorrect temperatures in the refrigerator or freezer
• Food spoiling faster than expected or freezing inappropriately
• Error codes related to temperature regulation
• The refrigerator running continuously or cycling too often

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a replacement outer housing cover that restores the appliance's exterior protection and appearance. It shields internal components from debris and helps maintain a finished look for the unit. What it does:

• Covers and protects internal components from dust, dirt and incidental contact
• Restores a clean, finished exterior where the original cover was cracked, warped or missing
• Helps prevent small objects from falling into internal openings
• Reduces visible wear on the appliance for a neater installation

• Disconnect power to the appliance before starting any work
• Remove any retaining screws or clips holding the old cover in place; lift or slide out gently
• Align the replacement cover carefully and re-secure with original hardware

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

Replacement push-button light switch that turns the interior light on and off when the refrigerator door opens. Replaces a failed or worn door-activated switch to restore interior illumination and make loading and unloading easier. What it does:

• Activates the interior light when the door opens and turns it off when the door closes.
• Restores visible interior lighting so food and shelves are easy to see.
• Stops lights from staying on or failing to come on if the original switch is worn or broken.
• Fits behind the fridge door trim where the original door switch mounts.

• Disconnect power to the appliance before servicing to avoid shock.
• Remove the door trim or liner cover to access the switch; keep track of screws and trim clips.
• Disconnect wiring harness or terminal connectors carefully; do not pull on wires.
• Reassemble panels and test the door action and light operation before returning to regular use.

The Thermistor is an OEM part for Frigidaire refrigerators and freezers, designed to accurately monitor and control the temperature within the appliance. This sensitive component reacts to temperature changes by altering its resistance, providing feedback to the control board to regulate the cooling and defrost cycles.  

Causes of thermistor failure can include physical damage, electrical failures within the circuit, or aging, which affects its accuracy and responsiveness.

Symptoms of a bad Thermistor include:

• Unusual temperature fluctuations in the refrigerator or freezer
• The appliance is constantly running or not cooling efficiently
• Error codes displayed on the refrigerator's control panel indicating thermistor problems
• Buildup of frost in the freezer or condensation in the fridge

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This molded evaporator cover replaces the plastic trim that protects and directs airflow over the freezer evaporator; it helps maintain even cooling and keeps ice and debris away from the coil assembly. Fits the OEM mounting locations for a proper seal. What it does

• Protects the evaporator coil from loose food and debris that can impede airflow.
• Directs cold air through the freezer compartment for more consistent temperatures.
• Helps reduce frost build-up on the evaporator by maintaining proper airflow patterns.
• Restores proper fit and appearance where the original cover is cracked, warped, or missing.

• One evaporator cover

• Disconnect power to the appliance before starting any repair.
• Remove screws or fasteners holding the old cover; handle tabs carefully to avoid breaking mounting clips.
• Defrost and dry the area if there is ice buildup before installing the new cover.
• Reassemble panels and verify there are no gaps that could allow air leaks or contact with moving components.

The Air Filter is an OEM part for Frigidaire refrigerators designed to keep the air inside your refrigerator fresh by reducing odors and filtering out unwanted smells, ensuring that the air circulating within your fridge remains clean and fresh. The filter is easy to install and is recommended to be replaced every six months to maintain optimal freshness.

Symptoms of a bad Air Filter include:

• Persistent odors despite cleaning.
• Increased buildup of odors.
• Noticeable decrease in the freshness of stored food.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This door gasket seals the refrigerator door to help maintain proper temperature and reduce energy loss. It replaces a worn, torn, or compressed seal to improve cooling performance and food safety. What it does:

• Creates an airtight seal between the door and cabinet to keep cold air in and warm air out
• Helps prevent frost build-up and reduces moisture inside the compartment
• Can stop visible gaps that allow warm air and odors to enter
• Restores consistent temperatures for better food preservation

• One refrigerator door gasket

• Handle gently to avoid stretching or tearing; follow the appliance manufacturer's alignment and fastening steps
• Clean the door flange and gasket channel before installation for a proper seal
• Some gaskets require heating (hair dryer) or a short break-in period to fully seat; follow your model's instructions

This replacement door gasket seals the refrigerator compartment to keep cold air in and warm air out, helping maintain consistent temperatures and reduce energy use. It fits along the cabinet opening and forms the primary seal between door and cabinet. What it does:

• Creates an airtight seal to help maintain internal cooling and reduce compressor runtime
• Prevents warm, moist air from entering and causing frost build-up or condensation
• Helps keep food fresher by maintaining stable temperatures
• Common symptom: visible cracks, gaps, or torn edges around the door perimeter
• Common symptom: warm spots inside the fridge, excessive frost, or higher energy use

• Unplug or disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the sealing surface thoroughly before installing the new gasket
• Some installations require basic hand tools; check the appliance's service guide for detailed steps
• If adhesive or clips are used, follow OEM instructions

This mounting bracket secures appliance components to the cabinet frame, restoring solid support and alignment. It's a straightforward replacement for worn, bent, or broken brackets that cause loose panels or misaligned doors. What it does:

• Provides structural support for interior or exterior panels and components
• Helps stop rattling or vibration caused by a loose or damaged bracket
• Restores proper alignment to doors or trim that shift due to bracket failure
• Used wherever a small metal bracket fastens parts to the appliance frame

• One mounting bracket

• Disconnect power to the appliance before servicing to avoid shock or injury
• Installation typically requires basic hand tools; keep fasteners for reuse unless replacement specified
• Handle edges and metal parts carefully to avoid cuts; consider gloves

This freezer air duct directs cold air from the evaporator fan through the freezer compartment, helping maintain steady temperatures and airflow. Replace a cracked, warped, or missing duct to restore consistent cooling and reduce frost or noise. What it does:

• Channels air from the evaporator fan outlet to the freezer vents for even cooling
• Helps maintain targeted freezer temperature and proper circulation
• A damaged or loose duct may contribute to weak airflow, frost buildup near vents, temperature swings, or rattling noises
• Seals the airflow path when properly seated to minimize leaks and hotspots

• 1 freezer air duct

• Disconnect power to the refrigerator before servicing
• Clear the freezer and remove any panels, shelves, or the ice bin as needed for access
• Remove mounting screws or clips, note seal orientation, and seat the new duct fully
• Reuse original hardware, restore power, and verify airflow from the vents

This sump is the dishwasher drain pump housing that channels wash and drain water to the pump, helping the appliance clear water quickly to prevent standing water. A direct-fit replacement when the original housing is cracked or leaking. What it does:

• Houses and seals the drain pump to direct wastewater out of the tub
• Prevents leaks by maintaining a secure pump-to-tub connection
• Helps maintain proper drain flow to avoid standing water or incomplete drains
• Commonly replaced for visible cracks, leaks under the appliance, or when the pump seal fails

• One sump (drain pump housing) as shown

• Disconnect power and water supply before starting any repair
• Inspect adjoining gaskets, clamps, and pump for wear; replace if damaged
• Handle plastic components carefully to avoid cracking; tighten fasteners to OEM specs

This cover is a replacement protective trim piece that shields internal components and restores the appliance's finished appearance. It helps keep parts protected from dirt while improving the unit's look. What it does

• Protects exposed components and wiring from dust and debris
• Restores damaged or missing exterior trim for a finished appearance
• Helps prevent accidental contact with internal parts
• Commonly replaced when cracked, broken, or missing

• One appliance cover as pictured and specified by the manufacturer

• Disconnect power to the appliance before starting any service
• Typically attaches with clips or screws; use appropriate tools and keep fasteners
• Handle carefully to avoid scratching the replacement part

This grille clip is a small plastic retainer that secures a refrigerator grille or trim piece to the cabinet, keeping the front panels aligned and preventing rattles or gaps for a tidy appearance. What it does:

• Secures the lower/front grille or trim to the appliance cabinet to hold it in place
• Prevents grille movement, rattling, or sagging that can occur with worn clips
• Helps maintain a tight fit between trim and cabinet for a finished look
• Simple replacement part when existing clip is cracked, broken, or missing

• One grille clip

• Typically snaps into place; inspect mating slot and clip orientation before installing
• Replace any damaged adjacent clips for even support and fit
• Work carefully to avoid damaging the grille or surrounding trim

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

Color: White

This replacement screw secures appliance components to their mounting points so panels, brackets, and trim stay tight and aligned. Replace missing or stripped hardware to restore a solid, rattle-free fit and proper assembly integrity.

• Secures panels, brackets, and trim to prevent movement and maintain alignment
• Replaces missing, damaged, or stripped hardware that can compromise assembly
• Helps reduce rattling or vibration from loose components
• Restores proper fit after service or access panel removal

• Unplug the appliance before servicing; turn off water supply if working near dispenser/ice areas
• Compare the new screw to the original to ensure thread, head style, and length
• Start threading by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Retain and reuse any original washers, spacers, or clips as required

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head