Thermador Cooktop Parts

The Jet Holder with Nut is an OEM part for Bosch ranges and cooktops. It holds precisely machined jets that control gas flow from each burner valve.

Causes may be wear and deterioration from prolonged heating exposure. Physical impacts or damage accumulation over time could also compromise the jet holder.

Symptoms of a bad jet holder can include:

• Inability to adjust or maintain proper flame stability and heat output
• Irregular or uneven flame patterns between surface burners
• Potential gas leaks observed at jet connections

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This pilot light lens covers and diffuses the control-panel indicator lamp. Replace a cracked, missing, or discolored lens to restore clear visibility of the light, protect the lamp opening, and keep the panel looking finished.

• Covers and diffuses the indicator lamp on the control panel
• Helps protect the lamp opening from debris and accidental contact
• Restores a clean, finished appearance to the panel
• Replace if the lens is cracked, missing, loose, or discolored
• Can help when the indicator is hard to see even when lit

• Disconnect power to the appliance before servicing and allow surfaces to cool
• Access the indicator opening from the front or rear (varies by design) and remove any retainer or clips holding the old lens
• Note orientation and transfer any existing retainer or gasket if present
• Seat the new lens fully, reassemble, and test the indicator light

If your oven won't start or runs with the door open, this door interlock switch detects proper closure and latching. DIY repair in under an hour.

This jet holder mounts in the burner assembly for a 12,000 BTU burner. It positions and secures the orifice (jet) and helps seal and align the gas path so the burner lights reliably and produces a steady flame.

• Holds and aligns the burner orifice for the 12,000 BTU burner
• Provides a sealed passage from the valve to the burner head
• Helps restore proper flame height and pattern when the original holder is stripped, cracked, or corroded
• Common symptoms: weak or uneven flame, burner won't light, or jet/orifice will not seat securely

• Shut off gas supply and power; allow the appliance to cool before starting
• Remove grates, burner caps, and burner head to access the holder
• Transfer the existing orifice/jet to the new holder; tighten fittings carefully—do not overtighten into soft metal
• Reassemble, restore gas, and perform a leak check with an approved solution

Fixes no spark at burners or oven not lighting issues. This ignition module generates the high-voltage spark needed to ignite gas at electrodes.

Replacement foot assembly for gas cooktop or range grates. Installs on the underside to cushion contact and stabilize the grate. Replace when worn, missing, or broken.

Replacement selector knob for your range. Fits onto the control shaft to select functions, cycles, or heat levels. Needed when original is cracked, broken, or missing.

This is an 8-inch coil-style surface heating element that plugs into a burner receptacle on the cooktop of your range. It provides radiant heat for cooking on the stovetop. Replace this element if the burner doesn't heat up, heats unevenly, produces visible damage such as pitting or blistering, or fails to glow red when turned on.

Air-gas mixing tube that connects the orifice to the burner head on gas cooktops. Replace if clogged, damaged, or missing to restore proper flame mixing.

The Burner Cap Assembly "C" Matte Blk is an OEM part for Bosch gas cooktops. As the rounded covering fitted over individual burners, it safely contains flames underneath cookware. Maintaining proper cap placement is vital for heating performance and safety compliance standards.

Causes of a bad burner cap assembly can include cracks or punctures from sustained high temperature cycling that compromise its insulating barrier. Over time, surface imperfections like scratches also diminish durability against consistent heat exposure.

Symptoms of faulty caps are:

• Flames improperly escaping from under pan edges
• Visible damage present on cap surfaces
• Inconsistent flame height adjustment or shut-off
• Excessive heat concentration in burnered area

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Burner won't light or clicks continuously? This spark ignition module generates the voltage needed to ignite gas burners. Moderate DIY repair.

Electrode that produces the ignition spark for gas ovens and ranges, restoring reliable burner lighting. Replace a damaged or worn electrode to stop repeated clicking, weak sparks, or burners that fail to light. What it does:

• Delivers the spark at the burner to ignite gas during startup.
• Common symptom fix: oven/range burners that won't light or that click continuously without producing a flame.
• Use when the electrode is cracked, corroded, or the ceramic insulator is damaged.
• Works as part of the appliance's ignition system alongside the spark module/igniter wiring.

• Turn off power and gas supply before beginning any service.
• Avoid touching or chipping the ceramic insulator; handle the tip carefully.
• Reconnect wiring exactly as removed and secure the electrode in the original orientation.

This 13.7 mm venturi tube mixes gas with air for proper cooktop burner operation. Replace if original is clogged, damaged, or needs removal for repairs.

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This is a trim ring or plate that sits around a control knob on a range or cooktop. It provides a finished appearance and helps indicate knob position settings on the control panel. Replace this piece if it is cracked, discolored, or missing, which can make it difficult to read burner settings accurately.

Pressure regulator for gas cooktops maintains consistent gas flow to burners. Replace if leaking gas odor, damaged vent, or worn seals detected.