We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Oven won't light or takes forever to preheat? A weak igniter is the likely cause. This glow igniter heats to ignite gas burners. DIY install in 30-60 min.
Replaced both ignitors. Since I was working on the range I also overhauled the final 2 of the 6 burners on the stove top. Venturi tube and jet nuts were frozen and could not remove drip tray for cleaning and access to ignitor clip. Had to drill out Venturi tubes using a tapered bore bit. Used Dremmel with cutting wheel to remove jet nut. This range has been heavily used since new for 16 years. Works like new, again. Read more
Most orders arrive by Tuesday, November 24
This is a gas tube or connector used in a range or cooktop to route gas from the supply line to the burner assembly. It ensures a secure, leak-free connection for proper gas flow. Replace this part if you detect a gas smell near the appliance, experience uneven flame, or notice visible damage or corrosion on the existing tube.
I had to cut out the venturi with one of those vibrating tools with a narrow metal blade like a hack saw. Takes time and wear your ear plugs . I had two different repair guys here they both said I need a new range . It's 15 years old and 9 grand to replace it. No No . I'll fix it and I did . Read more
This meat probe sensor is a temperature-sensing device that inserts into food while it cooks in the oven, allowing the oven to monitor the internal temperature and automatically stop cooking when the target temperature is reached. It connects to a jack inside the oven cavity via a heat-resistant cable. Replace this probe if your oven no longer reads the food temperature accurately, displays a probe error code, or if the cable or tip is visibly damaged.
Replaced Read more
Red indicator lens for gas cooktop burner controls. Replace when cracked, discolored, or missing to restore burner status visibility. Verify long vs short lens for your model.
Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.
At first, I thought that it was the defrost timer, but when I took apart the freezer, I found that the evaporator fan motor wasn't running, so I replaced it. Read more
Replacement jet holder for gas range and cooktop burners. Secures the orifice and channels gas flow. Order when original is corroded, damaged, or broken.
The oven was not heating, and there was no gas flow to the oven or spark. I replaced the spark igniter, but that did not fix it, so the problem was either the ignition device or the oven bake solenoid. In order to get to them, I had to cut the venturi tubes which hold down the burner rings with a Dremel tool, which was easy enough. There is no other way to get these tubes out if they are stiff or seized as you will simply twist the gas supply line to the burner if you try to rotate the nut.... Read more
Oven not heating or baking unevenly? This bake heating element restores consistent heat. DIY-friendly repair takes about 15 minutes with basic tools.
Simply removed the old heater and replaced it with the new one. Took 10 minutes Read more
This is a cooling fan assembly used in wall ovens and ranges to circulate air and prevent overheating of internal components and surrounding cabinetry. It helps dissipate heat from the oven cavity and electronics during and after cooking cycles. Replace this fan if you notice excessive heat on the outer surfaces of the oven, the fan runs noisily or intermittently, or the oven displays overheating error codes.
Fix burners that won't ignite or click. This spark module controls ignition for gas range burners. Common DIY repair takes about 10-15 minutes.
First I checked both spark igniters (range has two ovens) by testing them on the oven that did work. Both were good. I then checked the spark igniter wiring & it was good. At this point I contacted Appliance Parts Pros to ask which spark module I should order, the problem was that there wasn't a model number on the appliance. After speaking to the rep I ordered the ignition devise pictured above. Installed it and it worked! Read more
Oven won't heat or bakes unevenly? Replace your failed bake element to restore proper oven temperature. Simple DIY repair with two screws—takes 5-10 minutes.
We bought both bottom elements for each oven. They installed and now work PERFECTLY! Thank you! Read more
Replacement control knob for gas range burner or oven settings. Restores precise temperature control when original knob is cracked, broken, or missing.
Oven won't turn on or display is blank? This power control board supplies power to your range's electronic controls. Moderate DIY repair, 1-2 hours.
Not having any local Thermador support I took the advise from KC on the repair forum. The repair consisted of removing and replacing the control and relay board. The hardest part of the job was working behind the stove while it was pulled from the wall. ( didn't want to scratch my floor ). Over all the repair was simple just pulling wires from old board and installing on new board. The directions sent with the parts are excellent and easy for anyone to follow. I am glad I found this site... I... Read more
Oven door gasket seals the cavity to retain heat during cooking. Replace when torn, compressed, or allowing hot air leaks. Confirm fit by model number.
Replaced the display board and put in a new gasket to prevent the heat from escaping the oven and eventually "cooking" the display board. New parts worked perfectly and were easy to install, just had to keep track of a few screws and cables, nothing to it otherwise. Shipping was insanely fast- I ordered on a Friday afternoon, chose their standard shipping, and my parts were delivered the next day- Saturday morning- by 9am. My oven was working again by 10am. Amazing service! Read more
Black control knob for electric ranges and cooktops. Replaces cracked, broken, or missing knobs. Installs on burner control dial stem for precise heat adjustment.
I searched for the part online and was fortunate enough to find it on your website. Read more
The Burner Head and Cap Assembly is an OEM part for Bosch ranges and cooktops. It contains the burner itself along with its protective cover.
Cracks or misshapen portions disrupt flame stability leading to inconsistent results.
Symptoms of a failed assembly include:
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
Our appliance repairman said he would order a new burner cap. We waited 7 months; each time we called he said it was on order. After having to cook Thanksgiving and Christmas dinners on 3 burners we gave up and ordered the part ourselves. It took 5 days to get here and less than one minute to install; it fit perfectly and works like new. Read more
Gas burners won't light or keep clicking? This spark module generates consistent sparks to reliably ignite cooktop burners for safe operation.