Need Help?
Call
Jet holder securely houses the orifice assembly on gas range burners. Replace if cracked, corroded, or heat-damaged. Ensures proper gas flow and ignition.
First and foremost, don't believe everything you see on Youtube. In order to get to the gas solenoid that feeds the burner you MUST take the entire top off that side of the range. Remove the grates and burner tops. You will see 2x 20mm brass nut, or so it appears, that hold each burner in place on the splash/drip pan. It is not just a nut, it is a venturi that threads down into what is called the jet holder. You may get a socket on it and think you are getting it loose but, more than likely you... Read more
Grease filter for range hoods and over-the-range microwaves. Dimensions: 10-3/4" x 24-1/4" x 3/8" (10.75 x 24.25 x 0.375). Wing shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.
Searched your website & found the replacement filter that I thought was correct for my old vent hood. Read more
Oven won't heat or takes forever to reach temperature? A weak or failing igniter is the likely cause. This range oven igniter is a 10-minute DIY fix.
I replaced the igniter with a Frigidaire(Electrolux) part. The small oven on my Thermador Pro-Harmony Gas Range stopped heating (on Thanksgiving Day of course). I looked on the internet and I saw a video indicating it may be the igniter. I ordered both the Bosch igniter (00415504) and the Frigidaire (5303935066). Bosch and Thermador are the same company. The Bosch igniter looked like the existing Thermador except the connecting wires were too short. Therefore I used the Frigidaire/Electrolux... Read more
Fix a burner that won't light or sparks weakly with this gas cooktop igniter. Remove the burner cap and brass nut to access. Takes 5-10 minutes to install.
Appliance pros had the part. Incredibly, we received it the next day. They sent a confirming e mail with general instructions on how to replace it. Worked like a charm! Our's is a Bosch unit. The retaining brass nut in the center of the burner is an odd size-20 mm which I did not have among my many automotive metric tools. The local Auto Zone though had a 20 mm socket. Once that was removed the procedure would have been a breeze except the retaining screw on the old igniter was frozen. ... Read more
The Vent Control Button is an OEM component specifically designed for select Bosch downdraft ventilation ranges. Pressable from the countertop, its reliable switch operates the vent position. Precise guidance aligns ductwork airflows.
Symptoms of a faulty control button may include intermittent or unresponsive vent movement. Over-activation degrades contacts requiring change.
Causes of a bad button relate to typical contact wear reducing conductivity. Splashes introduce moisture necessitating replacement over time.
Causes of a bad vent control button involve:
This OEM Bosch part is also compatible with some Thermador, Dacor, and Viking downdraft ventilation ranges. Replace to maintain convenient vent management directing smoke and odors safely outdoors.
Found replacing the switch to be doable, but it was quite a delicate operation. This was for a Thermador range with a broken downdraft switch. It required the removal of 5 small screws which could easily be fumbled and dropped down where it would be difficult, if not impossible to retrieve. Two of the screws were facing the back, so it was a blind operation to remove and replace the screws. Required an offset screwdriver, as space was tight. So, be EXTREMELY careful to not drop the screws and... Read more
The Bake Element is an OEM part for Bosch ranges and ovens. It is responsible for generating heat through its calibrated heating coils to bake and roast foods evenly. Consistent heat production is essential for optimal cooking performance.
Causes of a bad bake element can include coil failure due to deterioration over time and heat exposure, cracks or damage to insulators, or interrupted electrical flow.
Symptoms of a failed bake element include:
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
We bought both bottom elements for each oven. They installed and now work PERFECTLY! Thank you! Read more
The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.
Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts.
Symptoms of a bad bulb include:
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
Changed light bulbs Read more
Fix a range that won't reach set temperature or shows temperature error codes. This sensor monitors oven heat and signals the control board to adjust.
Replaced the bake element. The manufacturer did not leave enough wire to pull the connections into the oven so I had to open the back and locate the connections. Read more
Oven not heating or baking unevenly? The bake element provides bottom heat for cooking. Easy DIY repair—just 2 screws and wire connectors. 10-15 minutes.
I took the model number of the oven and typed that in followed by replacement backing element.there was a photo of the element that matched the original. They provided an online tutorial as to how to install it. It was very easy because the electrical contacts at the ends of the new baking element slid right into the electrical contacts inside the oven cavity. The only thing that you had to be careful about was loosing the electrical contacts deep inside the oven. But I didn't see it as much of... Read more
Replace your worn oven door gasket to restore a tight seal, prevent heat loss, and maintain consistent baking temperatures. Confirm fit with your model number.
After watching your great video showing how to install, we ordered the product from you. Great service and an easy install!!! Thanks so much!! Read more
Heat-resistant seal for 30-inch ovens. Replace when worn or damaged to prevent heat loss and maintain consistent baking temperatures. Verify fit.
Simple rip and replace. Read more
Replacement inner glass panel for oven doors. Installs between door layers. Needed when original glass is cracked, chipped, or shattered from impact.
Removing the oven door, carefully taking it apart to remove the broken panel, cleaning everything, putting in the new glass panel and reassambling took me about an hour. To get to the glass panel takes unscrewing about 20 screws. Not too difficult to do. Assembly is easier than disassembly. Read more
Oven not heating? A failed bake element is the most common cause. This part generates heat for baking in the main oven cavity. Moderate DIY repair.
First guess was the Bake Element, but I ran my hands around it and didn't feel any clue of a break/failure in the element. Further research indicated that the Hot Wire Relay is the next likely cause, that was really bad news because that part is unavailable anywhere. Swapped the H1 and H2 wires on the Hot Wire Relay, and found that Broil still worked, which indicated that the relay was good and the Bake Element was the likely cause. This was good news because that Hot Wire Relay is made... Read more
Gas burner won't light or clicks repeatedly? This spark igniter electrode creates the spark to ignite gas. Simple DIY repair restores reliable ignition.
Replaced the ignition control boards. Read more
Oven won't light or takes forever to preheat? A weak igniter is the likely cause. This glow igniter heats to ignite gas burners. DIY install in 30-60 min.
Replaced both ignitors. Since I was working on the range I also overhauled the final 2 of the 6 burners on the stove top. Venturi tube and jet nuts were frozen and could not remove drip tray for cleaning and access to ignitor clip. Had to drill out Venturi tubes using a tapered bore bit. Used Dremmel with cutting wheel to remove jet nut. This range has been heavily used since new for 16 years. Works like new, again. Read more
Replacement rubber feet for gas cooktop grates. Kit includes 4 feet and adhesive. Needed when original feet are cracked, worn, missing, or fell off.
ORDERED NEW ONES FROM YOU Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.