Thermador Range Parts

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

Incandescent oven light bulb restores interior illumination so you can monitor cooking without opening the door. Replace when dim or burned out.

Wire oven rack slides into side supports to hold cookware at the correct height. Replace a bent, rusted, or missing rack to restore level support for baking.

This is a push button cap that fits over a switch on a range or oven control panel. It serves as the external interface that you press to activate a specific function such as ignition or lighting. Replace this cap if it is cracked, missing, or no longer staying in place, making it difficult to engage the underlying switch.

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

Protective boot that covers the capacitor terminal on your range hood. Replace if cracked, torn, or missing to shield connections from moisture and dirt.

The Surface Element (240V-2100W) is an OEM part for Bosch cooktops and ranges. It provides consistent, even heating from below pans on the cooktop surface.

Causes of a bad surface element can include normal wear and damage from extended, heavy usage. Food or liquid spills left on the element for prolonged periods could potentially corrode the coils or electronics over time as well.

Symptoms of a bad surface element include:

• Element not heating up at all or heating unevenly
• Element heating intermittently or stopping prematurely
• Buzzing, clicking or smoke coming from below the element
• Tripped or blown circuit breakers when using that element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This catalyzer element helps neutralize smoke and odors generated during cooking by breaking down airborne particles as they pass through the microwave's ventilation system. It is typically located near the exhaust area of the unit. Replace this part if you notice persistent smoke odors, reduced ventilation effectiveness, or visible deterioration of the catalyzer material.

1/4" gas supply tubing connects your range's gas line to the valve. Replace when damaged, cracked, leaking, or during valve service for safe operation.

Gas pressure regulator for ranges and cooktops. Controls fuel flow to burners. Replace if leaking, cracked, or damaged to restore proper gas delivery.

Supports the burner assembly and positions the cap for consistent flame distribution. Replace if damaged, warped, or causing burner misalignment.

Replacement door counterbalance spring for ranges. Installs inside the hinge assembly to support smooth door opening and closing. Needed when worn or broken.

A replacement pilot light indicator that notifies you when a range or cooktop burner circuit is energized. Restores a visible indication so you can quickly tell whether the appliance control is active. What it does:

• Illuminates when the burner or control circuit is powered to indicate an active state
• Helps diagnose control or power issues by showing whether voltage reaches the control panel
• Common symptom: no light on the control panel or indicator despite a burner selected
• Safe, low-voltage indicator used on select Bosch ranges and cooktops

• One pilot light indicator as shown

• Disconnect power to the appliance before attempting any service to avoid shock
• Access may require removing the control panel or trim
• Handle with care to avoid damaging the lens or terminals

Burner won't heat or stays on high? This infinite switch restores variable temperature control to your range surface element. Direct fit replacement.

Microwave not heating? A failed diode rectifier prevents proper power flow to the magnetron. This one-way current component is essential for heating function.

If your cooktop burner won't heat or shows no signs of power, this dual-size radiant element restores both inner and outer cooking zones in 30-45 minutes.