Thermador Range Parts

This kit includes a simmer control board that regulates low-heat burner operation on the cooktop, allowing precise temperature control at simmer settings. The board manages the cycling of the burner element to maintain consistent low temperatures. Replace this kit if your burners won't maintain a simmer, cycle erratically at low settings, or if the existing control board shows signs of damage or failure.

Oven won't heat or shuts off during use? This thermal fuse cuts power when temperature exceeds safe limits. Moderate DIY repair with multimeter testing.

Oven not heating evenly in convection mode? This rear convection heating element restores proper temperature. DIY-friendly, typically installs in 10-20 minutes.

Captures grease and cooking vapors to keep air fresh and prevent buildup. Replace when clogged or discolored. Verify fit by model number and dimensions.

This is a door seal sleeve that fits around the perimeter of the oven door to create a tight seal between the door and the oven cavity. It helps retain heat inside the oven and prevents hot air from escaping during cooking or self-cleaning cycles. Replace this seal if you notice heat escaping around the oven door, uneven cooking temperatures, or visible damage such as cracking, hardening, or gaps in the seal material.

This bake element heats the small oven cavity from below during Bake, delivering the radiant heat needed for preheating and consistent baking when the original element fails.

• Provides primary bake heat at the bottom of the small oven cavity
• Works with the oven control to preheat and maintain set temperature
• Common failure symptoms: no or weak bake heat, uneven baking, visible blistering/cracks, or a breaker trip when Bake is selected

• Disconnect power at the breaker before servicing
• Access is typically from inside the cavity; remove mounting screws, pull the element forward, and move wires one at a time
• Support wires so they don't retract into the insulation; avoid bending or stressing the new element
• Restore power and run a bake cycle to verify proper heating

This electronic PC board is the appliance's main control, processing inputs and directing power to components so cycles run correctly. Replacing a failed board can restore normal operation when the unit is dead, won't start, or stops mid-cycle.

• Interprets user inputs and sensor feedback to execute programmed cycles
• Switches relays to power motors, valves, heaters, and other loads as required
• Manages timing, temperature, and safety logic for consistent performance
• Typical failure symptoms: no power/won't start, unresponsive or erratic controls, cycles ending prematurely, recurring error codes

• Disconnect power before servicing; verify power is off with a meter
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time to identical positions on the new board to prevent miswiring
• Some models require service-mode setup or calibration after installation—follow your model's service documentation

Main broil heating element for the oven, designed to restore top-heat for broiling and browning. Replaces a failed broil element so the oven can produce even, high-intensity heat during broil cycles. What it does:

• Generates the high, direct heat at the top of the oven used for broiling and browning.
• Restores proper broil performance when the element no longer heats or glows.
• Fixes symptoms such as no broil heat, uneven browning, visible burn marks, or a broken/warped element.
• Works as the primary upper heating element used in broil cycles (main oven).

• Disconnect power to the range/oven at the breaker before starting any work.
• Remove oven racks and access the element from inside the oven; element typically secures with mounting screws and terminal connectors.
• Handle terminals and sharp metal edges carefully; wear gloves and eye protection.

Gas supply tube connects gas line to range burners. Replace if cracked, kinked, damaged, or leaking. Installs between supply valve and burner assembly.

Burner won't light or clicks continuously? This spark ignition module generates the voltage needed to ignite gas burners. Moderate DIY repair.

6-inch trim ring frames the surface element opening on your cooktop. Replace a discolored, warped, or missing ring to restore a clean, finished look.

This LP main jet regulates propane flow to a surface burner to maintain a clean, stable flame. Replace a clogged or incorrect jet to restore proper burner performance, especially when converting a cooktop or range from natural gas to LP.

• Meters LP gas to the burner head for correct flame size and combustion
• Direct replacement for a damaged, clogged, or incorrect jet during service or LP conversion
• May help with yellow/sooty flames, weak or overly high flames, uneven heating, or delayed ignition

• Shut off gas and power; allow the appliance to cool completely
• Remove grates, caps, and burner head to access the orifice holder
• Start the jet by hand, then tighten gently with the correct tool—do not overtighten
• After installation or any LP conversion, leak-test connections and verify a steady blue flame; other jets and the regulator may also require LP settings per the model's instructions