Tiller Blade

These quality tiller tines are used on a variety of yard tillers. Tiller tines are blades attached to the tiller that turn soil and prep it for cultivating a garden. As the tiller tines are used, they can become worn down, broken, or damaged through use or impact with rocks and other debris. These are C-shaped tines that can cut through dense soil.If the tiller tines are bent, dull, or damaged, they will need to be replaced, otherwise they might till the soil unevenly and may not reach the depth required. To replace the tines, remove the spark plug wire before taking off the tine shield end cover. Taking out the tines requires removing the cotter pin from the clevis pin so the clevis pin can be pulled out. Next, the tines can be pulled directly off of the shaft. Slide on the new tines and reinstall the clevis and cotter pins before using the tiller again.These tiller tines are an authentic OEM replacement part directly sourced from the manufacturer. It is sold as an individual part. The tines are compatible with tillers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Bolens, Yard Machines, MTD, Huskee, and Montgomery Wards.

This left-hand inner tines assembly sit next to the outer tines on the left side of tillers from a variety of major manufacturers. The tines are the part of the equipment that breaks up the soil to create a garden and allow cultivation. The part is made of strong metal, but over time it can start to wear down or break when running over large rocks or other items.If the tines are broken or have been worn down, they will need to be replaced. Tines that are worn will not dig into the earth as well as new tines. A hammer and a set of pliers are required to make the replacement. Remove the tines from the tiller after turning it off and taking out the spark plug wire. The new tines can be installed in the same place.These inner tines are made to be used with tillers created by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Cub Cadet, and Craftsman. It is sold as an individual part. This is a genuine OEM replacement part that is sourced directly from the manufacturer.

These outer tines are used on lawn equipment to help dig up the earth for gardening or other purposes. They are made of durable metal but may wear down after being used. The tines can also crack or break in some cases. When the tines have worn down or become damaged, they will need to be replaced.Take a look at each set of tines on the tiller to see how much they have worn down since being purchased. If they are half the size they were when new, they need to be replaced. The process of replacing the tines is simple and requires nothing more than work gloves and pliers. Use the pliers to remove the outer tines from the tiller so they can be removed. Install the new tines with the pins and the equipment will be ready to use.These outer tines are a genuine OEM replacement part that are directly sourced from the manufacturer. The tines are sold individually. They are made for use with tillers manufactured by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Cub Cadet, and Craftsman.

This lawn mower outer tine assembly is for lawnmowers. Tines are used for dethatching the lawn, which can be useful in the spring. The outer tine is attached to the inner tine.Tines may become damaged with regular use or sudden impact, as with hitting rocks or cement. Damage might present itself as chips in the metal, bending, or a full break. A damaged tine should be replaced right away. Otherwise, the equipment will not function properly and could be dangerous. A screwdriver or a pair of pliers will be needed to properly install the new tine.The metal outer tine assembly works as a replacement part for many brands of lawnmowers. Compatible brands include MTD, Yard Machines, Bolens, Yard-Man, Cub Cadet, Husky, and Troy-Bilt. The OEM part is sourced directly from the manufacturer and is sold as an individual replacement.

This left-hand bolo tine is a replacement part used for a tiller. This part is constructed of black metal and requires a wrench set for installation. This tine easy to install. The left-hand bolo tine attaches to the left tine holder and is used to dig up dirt in the area being tilled. This is a genuine OEM part sourced directly from the manufacturer and is sold individually.The left-hand bolo tine should be replaced if it is damaged or no longer working. If the tines become so worn that they are pointed, the tiller will not perform acceptably. The tiller will not dig as deeply nor will chop garden residues and cover crops. The tines are typically to be replaced as a set rather than individually.To replace the tines, begin by removing the sheer bolt with a wrench that connects the tine assembly to the tine shaft. Next by using either a wrench or small impact driver, remove all nuts and bolts disconnecting the tines from the tine holder. Replace the left-hand and right-hand tines, tightening with either a wrench or small impact driver, and reattach the tine holder assembly to the tiller securing it with the sheer bolt. The tines should slant into the inside of the tine holder. The tiller is now ready for use. This part is manufactured by Troy-Bilt and MTD.

This depth bar is an authentic OEM part sourced directly from the manufacturer for use on tillers to allow the tiller to dig into the ground and tear it up. The depth bar reduces the forward movement speed of the tiller which can be beneficial when the ground is hard-packed. If the depth bar breaks, it should be replaced to keeps the tiller operating efficiently. The depth bar is located on the back of the tiller. Before removing and replacing it, make sure the spark plug is removed from the machine and is parked on a flat surface. Remove the screws holding the depth bar in place. Set the screws aside. Line up the new depth bar with the holes and insert the screws. Tighten the screws and put the spark plug back in place. This depth bar a heavy-duty metal bar that is sold individually. It is designed for use in tillers manufactured by Poulan, Jonsered, and Husqvarna.

This replacement part is a tine assembly. It is a genuine replacement part made by MTD. This part is usually found in riding lawn mowers and helps the blades turn when cutting grass, similar to a spindle assembly. A new tine assembly might be needed if the user notices that the rotating mechanism in the lawnmower is not working as smoothly as during prior uses. This can be because is it possible that the tine can become stripped over time and cause the rotation to become rigid. Be sure the engine is completely powered off before attempting to replace this part. Refer to the proper user manual for more information regarding how to replace this part. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure long-lasting use.

This cleaning tine is a genuine Husqvarna part, sold individually. This cleaning tine can be used as a replacement part in a tiller. The purpose of a cleaning tine in a tiller is to remove dirt and other external materials, such as debris and pebbles, from the spade tines so that the tiller can be used in soil without potential obstruction or interference with its function.If the cleaning tine is struggling to perform its function due to damage in the form of denting, cracking, chipping, warping, or eroding, the cleaning tine should be removed and replaced by this genuine OEM replacement part. Always unplug the appliance before performing any kind of repair or replacement.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This cleaning tine is compatible with the following outdoor appliance brands: Husqvarna.