Parts for Dcs DD124: Tubs And Conponents Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

This lock nut filter plate secures and supports the dryer's lint filter assembly, keeping the filter seated and helping maintain proper airflow. It replaces a worn or damaged plate to restore a secure filter fit and reduce lint bypass. What it does:

• Holds the lint filter securely in the filter housing to prevent movement during dryer operation
• Helps maintain correct airflow by keeping the filter properly seated
• Prevents gaps that can allow lint to bypass the filter and collect in the housing
• Commonly replaced when bent, cracked, or when the filter no longer seats properly

• One lock nut filter plate

• Refer to your model's service manual or parts diagram for correct placement and orientation
• Disconnect power to the appliance before attempting any repair
• Handle sharp edges carefully and use appropriate tools to remove/install retaining hardware
• If other filter or housing components are damaged, replace them as needed for a proper repair

Fix dishes with food residue or slow draining with a new dishwasher drain filter assembly. Captures debris before it reaches the pump. Easy DIY fix.

Door trim seal kit for dishwashers. Replace if you notice water leaking around the door edges or visible wear on the seal. Verify fit with your model number.

Clear plastic tube that guides interior lamp light to control or compartment areas. Replace if cracked, cloudy, or missing to restore proper illumination.

Fix spotty, streaky dishes with this dishwasher rinse aid dispenser cap. Seals the rinse aid compartment to regulate flow during wash cycles.

Extends dishwasher drain hose by 11' 10". Replace missing or damaged extension kit to complete drain system installation or repair.

Wire clip secures the drain hose connection in your dishwasher. Replace if the original clip is broken, missing, or no longer holds the hose firmly in place.

Replace a dishwasher harness and fan assembly when your unit won't dry dishes properly or runs loud. Moderate DIY repair requiring basic tools.

Connects two sections of dishwasher drain tubing to restore a continuous path. Replace if cracked, broken, or leaking at the connection point.

This OEM replacement part is a dishwasher control board. The control board is the main circuit board that controls the dishwasher's essential functions. This includes turning the appliance on and off as well as controlling the desired settings. Over time, the control board can become inoperable after excessive use. If the dishwasher is no longer turning on or the buttons are not responsive, then the control board might need to be replaced.To replace the control board, start by unplugging the dishwasher. After the power has been shut off, proceed to open the dishwasher door and remove the inner panel that houses the control board. Unthread the screws that secure the panel in place and pull the panel off of the dishwasher door. Locate the old control board and remove the mounting screws that attach it to the dishwasher. Once removed, unplug the wire harness and any individual wires that are attached to the board. Reinsert the wires into their correct terminals on the new board and snap the new board back in place. Thread the mounting screws and reinstall the interior panel.This genuine replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with Fisher & Paykel brand dishwashers.

Designed for use on a dishwasher unit, this part is the control board. This part manages the functions of the dishwasher. These functions include the washing, draining, and drying cycles. If any of the cycles are not working, the control board could be the culprit. Some of the symptoms may include the washing cycle not running or the dryer function not working. This will be evident when the control panel buttons are pressed and the appropriate function does not start. Disconnect the dishwasher from its power source before replacing this part. It is a very easy process to replace this part. The person performing this process may wish to wear work gloves to protect their hands.This component is sold individually. It is compatible with dishwashers that are manufactured by Fisher & Paykel and DCS. It is sourced as a genuine OEM part straight from the manufacturer. This part is made out of durable materials.

Connects two sections of dishwasher drain tubing to restore a continuous path. Replace if cracked, broken, or leaking at the connection point.

The Motor Assembly Kit is an OEM part for Fisher & Paykel dishwashers. This kit includes the circulation pump motor and components that work together to circulate water throughout the machine during the wash cycle. The motor assembly plays an essential role in distributing water containing detergent to clean all dishes thoroughly. It is responsible for delivering the right pressures, temperatures, and water flow to ensure optimal cleaning results. 

Symptoms of a bad motor assembly include: 

• Inadequate or inconsistent water flow during the wash cycle
• Improper distribution of detergent 
• Insufficient cleaning and rinsing performance
• Loud noises or grinding sounds emanating from the dishwasher 

This OEM Fisher & Paykel replacement part is also compatible with some Kenmore models.

The Motor Assembly Kit is an OEM part for Fisher & Paykel dishwashers. This kit includes the circulation pump motor and components that work together to circulate water throughout the machine during the wash cycle. The motor assembly plays an essential role in distributing water containing detergent to clean all dishes thoroughly. It is responsible for delivering the right pressures, temperatures, and water flow to ensure optimal cleaning results. 

Symptoms of a bad motor assembly include: 

• Inadequate or inconsistent water flow during the wash cycle
• Improper distribution of detergent 
• Insufficient cleaning and rinsing performance
• Loud noises or grinding sounds emanating from the dishwasher 

This OEM Fisher & Paykel replacement part is also compatible with some Kenmore models.

Fix leaks around your dishwasher motor with this housing seal. Prevents water from escaping the pump area. Simple 20-minute repair for most models.

Complete seal kit with gaskets, O-rings, and tub seals to prevent dishwasher leaks. Replace when you notice water pooling or drainage issues. Verify fit with your model number before ordering.

Secures the linkage rod for stable mounting and proper alignment. Replace if cracked, broken, or missing to restore quiet dishwasher operation.

This clip link support is a small mounting clip used to secure linkages and cables inside the appliance, keeping moving parts aligned and preventing binding. It helps restore proper motion and reduces noise from loose linkages. What it does:

• Secures a linkage or cable to the cabinet or component bracket to maintain correct alignment
• Prevents linkages from shifting, which can cause sticking, binding, or improper operation
• Helps reduce rattling or knocking noises caused by loose or disconnected links
• Restores intended movement of door/valve/actuator linkages when the original clip is worn or broken

• One clip link support

• High-level replacement; remove power before accessing internal components
• Inspect surrounding linkage and fasteners for wear while installing the clip
• Use care not to damage nearby wires, hoses, or components when snapping the clip in place

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Protective cover for dishwasher wiring harnesses. Replaces cracked, broken, or missing covers that expose electrical connections. Installs over wire junctions.

Fixes dishes not cleaning properly on the bottom rack. This lower spray arm assembly restores proper water distribution in your dishwasher.

Replace your dishwasher's cuff socket O-ring seal to prevent leaks and maintain proper water flow. Essential when you notice water pooling or dripping. Verify fit with your model number before ordering.

Secures and positions your dishwasher drain hose to prevent kinks and improper routing. Replace if clip is cracked, broken, or missing for stable hose support.

Replace a faulty dishwasher dispenser wiring harness if detergent isn't dispensing or the dispenser door won't open. Moderate DIY repair, 30-60 minutes.

Secures hoses in your dishwasher to prevent leaks and water damage. Replace if loose, cracked, or causing connection leaks. Verify fit with your model.

Joins two dishwasher drain hoses or connects drain outlet to household drain. Replace if leaking, cracked, or causing drainage issues. Verify fit with your model number.

This replacement joiner drain hose connects dishwasher drain lines to the home drain or disposer, restoring proper wastewater flow and helping prevent leaks caused by brittle or damaged tubing. Simple, direct replacement for the original joiner hose. What it does:

• Links the appliance drain outlet to a house drain or garbage disposer to route wastewater away.
• Replaces cracked, split or collapsed joiner tubing that can cause leaks or poor drainage.
• Helps stop symptoms such as water pooling beneath the appliance, slow draining, or visible leaking at the hose connection.
• Designed to match OEM routing and connection points for a like-for-like drain path.

• Disconnect power and water supply before servicing.
• Remove existing clamps and fittings, then slide hose into place and secure with appropriate clamps; do not reuse corroded clamps.
• Ensure hose routing avoids kinks, sharp bends, and contact with hot engine parts; maintain proper high-loop or air-gap per local code.
• Run a short test cycle and check for leaks at both connections before returning the appliance to service.

Water softener assembly kit for dishwashers. Replace if dishes have spots or film, or hard water isn't being treated. Verify fit with your model number.

Small mounting tab that secures trim, panels, or shelving edges in your dishwasher. Replace if broken, missing, or cracked to restore stable attachment.

Wiring harness that connects the water softener system in your dishwasher. Replace if damaged, frayed, corroded, or connections are loose or broken.

This integrated install kit enables a built-in installation by providing the hardware needed to mount and align a custom cabinet or décor panel to the appliance. It helps achieve a secure, flush fit for integrated installations. What it does:

• Provides the mounting hardware and brackets used when fitting a custom cabinet or panel to the appliance
• Helps align and secure the door or panel so it sits flush with surrounding cabinetry
• Replaces missing or damaged installation hardware that can cause loose panels or poor fit
• Commonly used during new installs, cabinet refits, or when converting to an integrated appearance

• Always disconnect power to the appliance before beginning installation
• Follow the appliance's installation instructions for panel adjustments, weight limits, and mounting sequence
• Use appropriate tools and fasteners; do not overtighten to avoid damaging panel or appliance

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.