Parts for Kitchenaid KSB1575WH0: 02 - Unit Parts

The KitchenAid Blender Drive Coupler is an OEM part for KitchenAid blenders. This part connects the blender's motor to the blade assembly.

Causes for issues with the drive coupler often involve overloading the blender, blending hard or frozen ingredients without sufficient liquid, or simply the natural degradation of the component over time.

Symptoms of a malfunctioning Blender Drive Coupler include:

• The blender's motor running, but the blades not spinning
• Visible wear or damage to the coupler's teeth
• Unusual noises during operation, indicating a misalignment or damage

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Lock Jar is an OEM replacement part for Whirlpool Blenders. Securing the blending jar safely during operation, the lock enables smoothie and food preparation.

Causes of a faulty blender locking jar include normal wear of locking tabs and ridges that hold the jar in place through years of use. Exposure to liquid residue over time may potentially compromise lock performance.

Symptoms of a bad locking jar include:

• Potential tipping or detachment of jar during blending posing spill and injury risks
• Inability to achieve proper suction seal jeopardizing blend consistency
• Lock failure releasing sharp blade assembly with attached jar interior

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This painted housing replaces the oven backguard panel to restore the exterior finish and support surrounding controls. It gives a clean, factory appearance where the original housing is dented, scratched, or corroded. What it does:

• Provides the finished exterior backguard for the upper rear area of the range/oven
• Restores mounting and alignment for controls and trim pieces
• Helps protect internal components from incidental contact and debris
• Improves appliance appearance when the original housing is damaged or cosmetically worn

• Designed to install with factory fasteners; keep track of screws and brackets during removal
• Disconnect power to the appliance before beginning service to avoid electrical shock
• Use basic hand tools; avoid overtightening fasteners to prevent paint damage
• If retaining trim or control assemblies, support them during housing removal to prevent damage

This replacement seal keeps liquids and food particles out of the blender motor housing to protect internal components and help prevent leaks. Fits the motor assembly where the shaft passes through the housing. What it does

• Seals the motor shaft opening to help prevent liquid from entering the motor housing.
• Reduces risk of motor damage or shorting caused by leaks into the base.
• Helps stop leaking at the blender base or around the blade assembly when worn.
• Replace if the seal is cracked, flattened, swollen, or shows visible wear.

• Always unplug the appliance before disassembly and removal of the jar or motor housing.
• Remove the blade and jar assembly per the service diagram to access the shaft seal; inspect mating surfaces and replace damaged components.
• Ensure the new seal is seated evenly around the shaft and in its groove; do not force or over-stretch the seal.
• After reassembly, run a short water test (with the unit unplugged from any direct water source) to check for leaks before normal use.

This replacement appliance foot restores stable, level support for your appliance so it sits flush and reduces rocking or vibration. Use it to replace a worn or damaged leveling foot that prevents proper balance. What it does:

• Provides adjustable support so the appliance can be leveled on uneven floors
• Reduces rocking, excessive vibration, and movement during operation
• Helps correct uneven door/Drawer alignment caused by a collapsed or missing foot
• Restores proper weight distribution for safer operation

• Disconnect power and water before working on the appliance
• Tilt or raise the appliance per the manufacturer's guidance; use blocks or an appliance jack for safety
• Thread the foot into the mounting insert and adjust height until the appliance is level; hand-tighten and verify stability
• Do not exceed recommended force when tightening; inspect for secure fit and proper clearance