Parts for Ge GTH18CBDERBB: Unit Parts

Refrigerator condenser felt tape seals and insulates the condenser area. Replace when worn, torn, or losing adhesion to maintain efficiency. Verify fit with your model number before ordering.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Vinyl sleeve that fits over rods, tubes, or wires in your refrigerator. Replace if cracked, torn, or missing to protect contact points and reduce wear.

Fix a refrigerator that freezes food or runs too cold with this temperature control thermostat. Common DIY repair with video guide, typically done in 10-15 minutes.

Attaches to the control shaft to adjust temperature settings. Replace this knob if yours is cracked, broken, or missing to restore smooth control operation.

Molded frame that supports and protects refrigerator control components. Replace if cracked, broken, or damaged to restore proper alignment and secure mounting.

Refrigerator light not working? This light bulb socket holds the bulb securely and provides electrical connection. Easy DIY repair with video guide.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Rubber grommet cushions and stabilizes the evaporator fan motor in your refrigerator. Replace if cracked, worn, or missing to reduce vibrations and noise.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

Freezer icing up or fridge too warm? The defrost thermostat monitors evaporator temperature to prevent frost buildup. DIY repair in under an hour.

Fixes uneven cooling or frost buildup caused by a misaligned defrost heater. This holder assembly secures the element in place. 15-minute repair.

This drip shield deflects and channels condensation and meltwater away from sensitive components to help reduce puddling and ice buildup inside the refrigerator. It's a direct-replacement exterior shield for the evaporator/defrost area. What it does

• Channels defrost meltwater into the drain path to prevent pooling under shelves or crispers.
• Helps reduce ice buildup by directing water away from cold surfaces.
• Protects internal components and wiring from moisture exposure.
• Can resolve symptoms like visible water inside the fresh-food section or intermittent dripping.

• Disconnect power to the appliance before starting any repair.
• Typically installs with a few screws or snap tabs; keep fasteners from the original part for reassembly.
• Handle gently to avoid cracking the plastic; replace if warped or damaged.

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Refrigerator not cooling or ice building up on evaporator coils? The defrost timer controls the defrost cycle. DIY-friendly, installs in 5 minutes.

Refrigerator not cooling properly or making loud noise? The condenser fan motor circulates air over coils for proper cooling. Simple plug-and-play repair.

Refrigerator running hot or making loud noises? A worn condenser fan blade prevents proper airflow across coils. DIY repair in 30 minutes or less.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.

Freezer not cooling or frost buildup? This evaporator coil absorbs heat to maintain cold temperatures. Professional repair recommended due to refrigerant.

The Run Capacitor is an OEM part for GE refrigerators. It plays a crucial role in the refrigerator's cooling system by providing the necessary start and run voltage to the compressor. Without a properly functioning run capacitor, your refrigerator may struggle to maintain the desired temperature, leading to spoiled food and inefficient energy use.

Causes of a bad run capacitor include electrical surges, wear and tear over time, or overheating due to a malfunctioning refrigerator compressor or poor ventilation.

Symptoms of a bad Run Capacitor include:

• The refrigerator compressor fails to start.
• Unusual humming noises coming from the refrigerator.
• The refrigerator cycles on and off more frequently than normal.
• A noticeable increase in energy consumption as the refrigerator struggles to maintain the proper temperature.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Fix a refrigerator that won't cool and clicks every few minutes. This start relay and overload assembly mounts on the compressor to restore reliable starting.

A threaded mounting bolt that secures the compressor to the refrigerator's frame, providing vibration dampening and structural support. Replace when you hear excessive compressor noise, vibration, or notice the compressor appears loose or misaligned.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

Secures brackets, panels, and internal components in your refrigerator. Replace missing or damaged screws to eliminate rattles and keep parts aligned.

Hex washer head screw for refrigerators, freezers, and other appliances. Replaces lost, stripped, or damaged screws during repairs or panel assembly.

Secures the condenser unit in your refrigerator. Replace if loose, broken, or causing vibration noise. Verify fit with your model number before ordering.