Parts for Ge PT925DN1BB: 02 - Upper Oven Parts

Small rubber bumper that cushions contact between oven door and cabinet. Replace if cracked, missing, or worn to reduce noise and protect finishes.

Oven won't heat or shuts off unexpectedly? This high limit switch cuts power when temperatures exceed safe levels. Moderate DIY repair, 1-2 hours.

Fix F2 error codes and inaccurate oven temperatures by replacing a faulty temperature sensor. Simple 15-minute DIY repair with basic tools.

Seals the back lamp assembly in your wall oven to prevent heat loss and moisture intrusion. Replace if cracked, brittle, or no longer sealing properly.

Replace your oven's halogen bulb when the interior light burns out or dims. Illuminates the oven cavity so you can monitor cooking without opening the door.

This SPDT high-amp switch controls high-current circuits by switching one input between two outputs, restoring proper electrical control in affected appliance functions. Built for high-load switching where reliable on/off selection is required. What it does:

• Directs high-current power from a single input to one of two outputs (single-pole, double-throw action)
• Replaces worn or failed selector/limit-style switches that cause intermittent or no power to a circuit
• Commonly used where a high-amp, durable switching contact is required to complete a function
• Helps stop symptoms like intermittent operation, failure to switch between states, or no power to the controlled circuit

• One SPDT high-amp switch (WB24T10160)

• Disconnect power to the appliance before inspecting or replacing the switch
• Verify wiring locations and take a photo before removal for correct reconnection
• Use proper tools and avoid touching energized contacts;

Top cabinet trim panel for wall ovens. Replaces cracked, broken, or missing trim pieces around the oven cabinet edge for a finished look.

Upper cavity wrapper assembly for wall ovens. Structural frame component that surrounds the cooking chamber. Replace if cracked, damaged, or corroded.

A replacement frame board assembly that secures the oven/range control console and gives the control area a finished appearance. Restores proper mounting and protection for the control electronics so buttons and displays sit correctly. What it does

• Provides the structural frame and mounting surface for the range/oven control console and control board.
• Protects control electronics and wiring from exposure and interference.
• Keeps front control buttons, switches and displays aligned and stable.
• Restores the unit's finished appearance when the original frame is cracked, bent or broken.

• Disconnect power to the appliance before starting work to prevent shock or damage.
• Handle sharp sheet-metal edges carefully and keep small fasteners organized for reassembly.
• Some disassembly of the backguard or control console may be required to access mounting screws.

The Control Board is an OEM part for GE ovens. As the central control unit, the control board monitors and regulates critical cooking functions such as temperature settings, timers and safety features.

Causes of a bad control board can be normal wear and tear over time, exposure to heat and moisture leading to corrosion of electronic components, or accidental damage.

Symptoms of a bad control board include:

• Unresponsive control panel or dim/missing display
• Inability to select bake or broil temperatures
• Failure to preheat or maintain proper temperatures
• Safety sensors not functioning correctly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This bracket relay board secures and connects a range/oven relay assembly to the appliance chassis, restoring a stable mounting point for reliable power switching. Designed to hold relays and related wiring in the correct position. What it does:

• Provides a secure mounting platform for the relay assembly to keep electrical contacts aligned.
• Maintains proper spacing and support for relay wiring to reduce strain and intermittent connections.
• Helps prevent relay movement or vibration that can cause arcing or noise during operation.
• Restores factory mounting when replacing a damaged or bent relay bracket.

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Handle connectors and wiring gently; ensure all wire terminals are fully seated on the relay board.
• Use existing mounting hardware or manufacturer-recommended fasteners; tighten screws to a snug fit without over-torquing.

This oven rack is a replacement chrome wire shelf that supports cookware and bakeware inside the oven, restoring proper airflow and cooking position. It slides into the oven's rack rails and provides a stable surface for pans and trays. What it does

• Replaces a missing, bent, or damaged oven rack so cookware sits level during baking and roasting
• Restores proper rack spacing and airflow for even cooking
• Allows trays and pans to slide in and out smoothly when rack rails are intact
• Helps prevent cookware from tipping or sliding during use

• One chrome oven rack

• No tools typically required; slide rack into the oven's existing rack guides until it seats securely
• Inspect rack rails for damage or buildup and clean before installing to ensure smooth operation
• Use oven mitts or heat-resistant gloves when removing or installing racks in a hot oven
• Do not modify the rack; replace if bent or warped

Oven not heating or baking unevenly? This bake element assembly restores consistent lower heat for proper cooking. Moderate DIY repair for most models.

Broil shield assembly installs behind the broil element to protect oven cavity from direct heat. Replace if cracked, warped, or damaged from exposure.

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.

These GE screws are a 12-pack of OEM replacement parts responsible for securing and fastening various components and panels in a GE range or oven. These screws are designed with a hexagonal head, which allows for the use of a compatible wrench or socket for tightening. They are commonly used to attach sheet metal panels, brackets, and other parts within the appliance, ensuring that these components remain securely in place during operation.

This part fixes the following symptoms:

• Loose or wobbly parts or panels within the appliance's interior or exterior
• Panels or components falling out of place, creating gaps or exposing internal parts
• Unusual noises or rattling sounds during the appliance's operation

The GE screws can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

ST10-16 X 7/16"

Replacement mounting screw secures panels, brackets, and controls on ranges and ovens. Needed when original screws are missing, stripped, or damaged.

Black. 8-18 AB HXW 3/8

Wire harness assembly connecting sail switch and temperature probe in wall ovens. Replace if wires are frayed, connectors damaged, or harness is worn.

Wire harness connecting relay board to sensor in wall ovens. Replace if wires are frayed, connectors damaged, or harness is melted or broken.

10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.