Parts for Ge ZET2RM4SS: 02 - Upper Oven Parts

A small rubber door bumper that cushions the contact point between the appliance door and cabinet to reduce noise, prevent chipping, and help the door close smoothly. Simple replacement restores quiet operation and protects finishes. What it does:

• Cushions the door edge to stop metal-on-metal or door-on-cabinet contact
• Helps the door sit and close more evenly to reduce misalignment symptoms
• Reduces banging, rattling, and scraping noises when the door closes
• Prevents wear and cosmetic damage at the door contact point

• Inspect the door/cabinet contact area to locate the bumper before replacing
• Most installations press the bumper into a hole or recess; use steady, even pressure to seat it
• If the old bumper is glued or fastened, remove residue and check the mounting method in your parts diagram
• Turn off power to the appliance before working near electrical components or wiring

The Hi-Limit Switch is an OEM replacement part for GE ranges. It is a safety component responsible for monitoring internal oven temperatures. The hi-limit switch helps prevent overheating by detecting when excessive heat has built up inside the oven cavity. It will automatically cut power to the bake/broil elements if temperatures rise too high.

Causes of a bad hi limit switch can include normal failure after years of exposure to heat, or issues with the electronic components or calibration.

Symptoms of a bad hi-limit switch include:

• The oven failing to heat up or bake/broil food properly
• Frequent thermal cut outs requiring the oven to be unplugged
• Delays in the oven reaching the set temperature
• Oven will not turn on

This is a genuine OEM part that works for some models of GE, and Hotpoint models.

This lower bake element restores consistent bottom-heat for proper baking and preheating in electric ranges and wall ovens. Replacing a failed element helps eliminate undercooked centers and uneven results.

• Provides primary bake heat from the bottom of the oven cavity
• Common failure signs: no heat in Bake mode, very slow preheat, uneven baking, or visible damage
• Helps ensure stable oven temperatures when paired with a working broil element and thermostat
• Direct-fit replacement designed to connect to existing wiring and bracket mounting

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and transfer wires one at a time to the new element
• Avoid stressing or loosening terminal connections; secure the bracket firmly
• After reassembly, restore power and test Bake to verify proper operation

The Temperature Sensor is an OEM part for GE ovens. It plays a role in monitoring and regulating the oven's internal temperature, ensuring accurate heating and cooking performance. This sensor works by detecting the temperature inside the oven cavity and communicating with the main control board to maintain the set temperature throughout the cooking process.

Causes of a bad Temperature Sensor can include exposure to extreme temperatures leading to sensor failure, wear and tear over time, or damage from oven cleaning agents or spills that may affect its functionality.

Symptoms of a bad Temperature Sensor include:

• Oven not reaching the set temperature.
• Overheating or underheating, leading to unevenly cooked food.
• Frequent error messages from the oven's electronic control.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This retainer bolt fastens and secures internal appliance components to keep panels and assemblies stable during operation. It's a direct-fit replacement designed to restore proper hold and reduce looseness or vibration. What it does:

• Secures appliance parts and assemblies in place to prevent movement during use
• Restores proper alignment of panels or components that become loose
• Functions as a hardware fastener where the original retainer bolt was used

• One retainer bolt

• Disconnect power and, if applicable, gas supply before starting any repair
• Start threads by hand to avoid cross-threading; tighten with appropriate hand tools
• Do not overtighten—secure snugly to avoid stripping threads or damaging components

Restore bright, clear visibility inside your oven with this 20-watt halogen light bulb. Replace a burned-out bulb to monitor cooking through the window and safely see racks and dishes without opening the door. What it does:

• Illuminates the oven cavity when the light switch is used or the door is opened
• Helps you check cooking progress and locate items inside the oven
• Common symptoms: interior light won't turn on, is dim or flickers, or the bulb glass is broken
• 20-watt halogen design matches the original lighting specification

• 1 halogen light bulb

• Disconnect power at the breaker and allow the oven to cool completely
• Wear gloves or use a clean cloth; avoid touching the glass envelope
• Remove the lens/cover per your model instructions; carefully remove the old bulb and fully seat the new bulb
• Reinstall the cover, restore power, and test; use only the wattage/type specified for your appliance

This halogen lamp assembly restores bright interior lighting so you can clearly see inside the oven while cooking. It replaces a burned-out or dim oven light and helps improve visibility when checking food. What it does:

• Provides the oven's interior light source so you can monitor cooking without opening the door
• Replaces a failed or burned-out halogen lamp
• Fixes symptoms such as no light, dim or flickering interior lighting
• Fits into the oven's light housing and connects to the existing lamp socket

• Disconnect power to the appliance before servicing to avoid electric shock
• Allow the oven and existing lamp to cool completely before touching the lamp
• Handle the halogen bulb with a clean cloth or gloves; oils from skin can shorten bulb life
• Make sure the connector is fully seated and the mounting is secure before restoring power; test the light after installation

This replacement crystal lamp provides the interior lighting for refrigerators, improving visibility so food and shelves are easier to see. Designed as a direct-fit replacement to restore a clear interior light. What it does:

• Illuminates the refrigerator interior to help you find items more easily.
• Replaces a cracked, broken, dim, or missing lamp assembly.
• Fits into the existing lamp housing and works with the original socket.

• Disconnect power to the appliance before starting any work to avoid electrical shock.
• Handle the lamp carefully—wear gloves or use a cloth to avoid cuts from glass.
• Remove old lamp assembly per the owner's manual; align and seat the new lamp securely in the housing.

This clip retainer secures the oven door glass to the door frame to keep the glass stable during use and prevent rattling or separation. Simple replacement restores proper glass alignment and reduces vibration noise. What it does:

• Holds the inner door glass in position inside the oven door assembly.
• Prevents the glass from shifting, rattling, or contacting other door parts.
• Helps maintain a safe, stable door assembly after a cracked or missing clip.
• Commonly replaced when the glass feels loose or the door vibrates during operation.

• One clip retainer for door glass.

• Disconnect power to the appliance before starting and allow the door to cool completely.
• Remove the oven door per the manufacturer instructions and handle glass with care — support both pieces of glass when separating.
• Use basic hand tools; keep track of screws and any spacers removed.

This probe thermistor monitors interior temperature and sends readings to the control board so your appliance can maintain the correct cooling cycle. It replaces a failed or inaccurate sensor to help restore proper temperature regulation. What it does:

• Senses air or evaporator temperature and reports it to the control module
• Commonly related to warm/freezing issues, incorrect temperature readings, or erratic cycling
• Used by the control system to trigger fans, defrost, and compressor operation as needed
• Works as a direct replacement for the listed OEM temperature probe

• Disconnect power before replacing to avoid shock or damage
• Handle the sensor tip and wiring gently to avoid damage to the element or insulation
• Route and secure the wiring so it does not contact moving parts or hot surfaces

This vent tube assembly routes exhaust air and helps direct airflow away from the appliance to maintain proper ventilation and operation. It replaces a damaged, cracked, or disconnected tube to restore correct air discharge. What it does:

• Channels exhaust airflow from the appliance to the external vent path
• Prevents air leaks that can reduce venting efficiency or cause mild odors
• Replaces tubes that are cracked, split, corroded, or otherwise damaged
• Helps maintain consistent airflow for proper appliance performance

• One vent tube assembly as shown

• Disconnect power (and gas if applicable) and unplug the appliance before beginning work
• Use appropriate tools and fasteners; do not overtighten clamps to avoid crushing the tube

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a replacement black screw used to secure interior or exterior appliance components. It provides a discrete, color-matched fastener to restore proper fit and stop rattles or loose panels. What it does

• Fastens trim, panels, brackets or control components where a small black screw is required
• Restores secure mounting to eliminate vibration, rattling or misaligned parts
• Matches finished appliance surfaces for a clean, unobtrusive look
• Simple hardware replacement for small fastener loss or damage

• One black screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver to seat the screw; avoid overtightening to prevent stripping or cracking surrounding material
• Keep track of small fasteners during disassembly and handle with care
• Replace with the exact part number if the original screw is damaged or the thread/length differs

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance components to the chassis or assembly
• Replaces a missing, stripped, or corroded screw
• Helps resolve loose panels, wobbling parts, or vibration noises
• Supports proper alignment of mounted parts

• Disconnect power at the breaker; for gas units, also shut off gas supply
• Allow the appliance to cool completely before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly without overtightening; replace damaged threads or hardware as needed

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.

This black-finished screw secures appliance panels, brackets, or trim in place. Replacing a missing or damaged fastener restores a solid fit and helps prevent rattling, gaps, and loose components.

• Fastens panels, trim, brackets, or covers on the appliance
• Helps maintain proper alignment and reduces vibration noise
• Common replacement when the original is lost, stripped, rusted, or broken
• Symptoms include loose or wobbly parts, rattling, or visible gaps

• Disconnect power; for gas appliances, also shut off the gas supply
• Allow hot surfaces to cool before servicing
• Start threads by hand to avoid cross-threading, then tighten snugly—do not overtighten
• Reuse any original washers or spacers in the same order and location

Package of 12

Black. 8-18 AB HXW 3/8

This 10-32 machine screw secures brackets, panels, and other hardware in cooking appliances. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned and safely fastened. What it does:

• Fastens panels, brackets, and components using a 10-32 machine thread
• Replaces hardware that is missing, rusted, or stripped
• Helps address loose or rattling parts and minor panel misalignment
• Maintains secure mounting after service or part replacement

• One 10-32 machine screw

• Disconnect power; for gas appliances, also shut off gas before service
• Support the panel or bracket while removing/installing hardware
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace them one at a time to keep alignment