Wall Oven Panel Parts

This is the oven's bottom broiler pan that catches drips and supports broiling cookware for safer, cleaner cooking. It restores the oven's drip containment so you can broil and roast without excess mess. What it does:

• Catches grease and food drippings to help prevent spills and oven fouling
• Provides a stable surface for broiling pans and racks during high-heat cooking
• Helps reduce flare-ups by containing drips below the food
• Useful when replacing a worn, dented, or missing oven pan

• Allow the oven to cool and disconnect power before removing or installing the pan.
• Slide the pan into the oven bottom on the support ledges; no tools required for typical installation.
• Clean pan after each use per your oven manual to avoid heavy buildup; use non-abrasive cleaners to protect surface.
• Replace if pan is warped or damaged to ensure proper fit and performance.

This oven bottom pan replaces the removable bottom tray that catches spills and protects the oven floor, restoring an even surface for cooking and easier cleanup. Fits in the lower cavity under the oven racks. What it does:

• Provides a durable, porcelain-coated surface to catch drips, crumbs and spills during baking and roasting
• Helps prevent spills from contacting the oven floor and heating elements
• Restores a flat, stable cooking surface for pans and bakeware
• Can reduce time spent scrubbing baked-on messes when used with proper liners

• One oven bottom pan

• Allow the oven to cool completely and disconnect power before replacing the pan
• Remove oven racks, slide out the old pan, then slide the replacement into the same position
• No special tools typically required; handle carefully to avoid chipping the coating

Color: Stainless

This replacement base restores a solid mounting platform for the assembly it supports, keeping components aligned and secure. Replace a cracked or warped base to eliminate looseness, rattling, or misalignment that can lead to premature wear.

• Supports and secures the associated assembly for proper operation
• Maintains alignment to reduce vibration and noise during use
• Helps protect connected parts by preventing shifting and flexing
• Replace when you see cracks, warping, stripped/broken mounts, or symptoms like rattling, looseness, or poor fit

• Disconnect power; shut off water or gas if applicable
• Wear cut-resistant gloves and handle edges carefully
• Document screw locations/routing; transfer any reusable clips or bushings from the old base
• Start screws by hand and avoid overtightening, especially into plastic bosses

This control panel is the front fascia that houses the cycle buttons and indicators on your appliance. Replacing a damaged or unresponsive panel restores reliable selections and a clean, factory appearance.

• Provides the user interface for selecting cycles and options
• Communicates button presses to the control system to start and customize operation
• Covers and protects components while finishing the appliance's front
• Common symptoms: cracked/broken console, worn or sticky buttons, selections not registering, intermittent response

• Disconnect power at the breaker before servicing
• Remove mounting screws/clips to release the existing console; support it to avoid straining wiring
• Transfer the user interface module and any brackets from the old panel as needed; avoid pinching ribbon cables
• Reinstall hardware and verify button response before completing reassembly

The Control Panel is an OEM part for Whirlpool ranges. It facilitates precise input and display of cooking functions.

Causes of replacement include failure of embedded circuits or damage allowing moisture penetration through the membrane surface over time. Physical impacts can distort switch responsiveness.

Symptoms of issues involve:

• Ghosting or pixelation impairing display readability
• Refusal of elements to toggle through temperature settings
• Unresponsive selection buttons due to circuit interruptions
• Inaccurate temperature calibration requiring technician attention

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement backsplash restores the rear panel that protects the wall behind a freestanding range and gives the appliance a finished appearance. It helps contain splatter and shields wiring and components from spills and debris. What it does:

• Covers the rear opening of the range to protect adjacent walls from grease, steam and food splatter
• Shields wiring and control components located at the back of the appliance
• Restores a clean, finished look when the original panel is dented, rusted or missing
• Helps prevent debris from entering the cabinet and control cavity

• Disconnect power to the range before beginning any work
• Use proper lifting support; a second person may be needed to hold the panel during installation
• Retain and reuse factory screws and fasteners unless replacement hardware is specified
• Handle edges carefully to avoid cuts; align mounting tabs and secure firmly but avoid overtightening