Wall Oven Trim

This left-hand side trim finishes and protects the edge of the appliance's panel or housing, restoring a clean, factory look. Replace when the original trim is cracked, missing, or loose to keep panels aligned and edges covered.

• Provides a finished edge on the left side and improves overall appearance
• Helps cover gaps and protect edges from snags or chipping
• Aids proper alignment of adjacent panels or consoles
• Replace if cracked, warped, loose, or missing
• Common symptoms: visible gap on the left side, rattling/loose panel, sharp or broken edge, cosmetic damage

• Disconnect power before servicing; also shut off gas supply
• Wear cut-resistant gloves; edges and surrounding panels can be sharp
• Left/right orientation is determined when facing the front of the appliance
• Align the trim and secure with existing hardware; do not overtighten fasteners

Color: White

This replacement frame restores the appliance's front cabinet trim for a finished look and secure component fit. It helps protect internal parts and keeps the control area or door edges properly aligned. What it does:

• Replaces damaged, cracked, or warped front trim that affects appearance or fit
• Secures adjacent panels and provides a mounting surface for controls or seals
• Helps stop drafts or gaps that can form around doors or control openings
• Restores proper alignment to reduce rubbing or interference with moving parts

• One replacement frame as pictured

• Disconnect power (unplug or switch off breaker) before starting any repair
• Basic hand tools (screwdriver, nut driver) are typically required; keep fasteners for reuse if intact
• Handle edges carefully to avoid scratching the finish; protect surrounding surfaces during installation

This vent control damper assembly opens and closes the appliance vent to allow steam and exhaust to exit when needed, helping maintain proper airflow and reduce moisture buildup. It replaces a worn or stuck vent actuator. What it does:

• Operates the vent/damper to allow exhaust air to escape during use
• Prevents vent from staying stuck open or closed, which can cause excess moisture or reduced airflow
• Restores proper venting function when the original damper fails or binds
• Works as the mechanical control between the appliance cavity and external venting path

• One vent control (damper) assembly

• Disconnect power to the appliance before beginning any service
• Access may require removing exterior panels or the back cover
• Handle the damper gently to avoid bending the flap or linkages

The side trim is a finishing piece that covers the appliance's right edge. Replacing a damaged or missing trim restores the factory look and helps keep adjacent panels aligned for proper fit.

• Finishes and protects the right-side edge of the unit for a clean appearance
• Helps align and secure adjoining panels or console components
• Reduces unsightly gaps that can collect debris
• Common symptoms: cracked, chipped, warped, loose, or missing trim; rattling or poor panel alignment

• Disconnect power to the appliance before service; allow hot surfaces to cool
• Wear cut-resistant gloves—edges and surrounding panels can be sharp
• Note right-hand orientation; transfer any clips/brackets from the old trim if present
• Align tabs and fasteners carefully; tighten hardware just snug to avoid distortion

This bottom trim assembly replaces the lower front trim on a 30" range or oven, restoring a finished stainless appearance and protecting the lower cabinet area. It fits where the original lower trim has dented, scratched, or separated. What it does

• Covers and protects the lower front of the appliance cabinet and kick area
• Restores the oven/range's finished stainless look after cosmetic damage
• Prevents dirt and debris from collecting beneath the appliance front
• Helps maintain proper airflow by keeping the lower opening closed

• One bottom trim assembly (30" stainless)

• Designed for front/lower mounting; follow the appliance service manual for exact fastener locations
• Use proper tools and avoid overtightening to prevent stripping or warping the trim
• Disconnect power to the appliance before working near electrical components

The Control Board is an OEM part for GE ovens. As the central control unit, the control board monitors and regulates critical cooking functions such as temperature settings, timers and safety features.

Causes of a bad control board can be normal wear and tear over time, exposure to heat and moisture leading to corrosion of electronic components, or accidental damage.

Symptoms of a bad control board include:

• Unresponsive control panel or dim/missing display
• Inability to select bake or broil temperatures
• Failure to preheat or maintain proper temperatures
• Safety sensors not functioning correctly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.