Parts for Ge GUD27ESPM0DG: Water System Parts

Size: 8 - 18 ab.

This is a replacement 8-18 threaded hex-washer-head screw (3/8" length, zinc finish) used to secure panels and components on compatible appliances. It restores proper fit and stops rattling or loose parts. What it does

• Fastens panels, brackets, or assemblies where an 8-18 threaded screw is specified
• Replaces missing or damaged screws that cause loose panels or vibration
• Restores secure mounting for trim, brackets, or internal components
• Matches OEM head style and finish for correct fit and appearance

• One replacement screw (8-18 x 3/8", hex washer head, zinc)

• Disconnect power and water before starting any repair
• Use the correct driver or bit to avoid stripping the head
• Do not overtighten; snug to secure components without deforming parts
• If other fasteners are damaged, replace them with identical OEM parts

This clamp is a small retaining fastener used to secure hoses, tubes or wiring to appliance fittings and keep connections stable during operation. It helps prevent leaks, chafing and loose connections that can cause performance issues. What it does:

• Secures a hose or tube to a barb or fitting to maintain a tight seal
• Prevents hoses and lines from slipping free during use or vibration
• Reduces wear from rubbing or chafing by holding components in place
• Helps stop minor leaks at hose junctions when properly seated

• One clamp (quantity: 1)

• Disconnect power and water supply before servicing the appliance
• Drain or catch any residual water from hoses before removing the old clamp
• Use the correct pliers or screwdriver for the clamp type; avoid over-tightening which can damage hoses
• Inspect adjacent hoses and fittings and replace any worn components while accessible

The Dual Coil Water Valve is an OEM replacement part for GE washing machines. It is a solenoid valve that controls the flow of hot and cold water to the washer.

Symptoms of a faulty valve include: 

• Failure to adequately fill or drain the wash tub
• Imprecise washing from too much or too little water  
• Oversudsing or excess vibration due to unbalanced levels

Causes can be worn seals or mineral buildup impeding proper valve movement after extended use.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This water inlet assembly controls water flow to the appliance's dispenser and ice-making system, restoring proper fill and preventing unwanted leaks when the original valve fails. It replaces a worn or leaking inlet valve for reliable water delivery. What it does:

• Opens and closes to allow water into the dispenser and ice maker when requested
• Stops water flow when the dispenser or ice maker is idle to prevent leaks
• Commonly replaces valves that cause no water at the dispenser or ice maker not to fill
• Can resolve slow fill, intermittent dispensing, or visible leaking at the valve

• One water inlet assembly

• Disconnect power and shut off the water supply before starting work
• Turn off and drain any connected water lines to avoid spills
• Tighten fittings to the manufacturer torque; use proper replacement gaskets/seals if required

A replacement tub outlet clamp that secures the drain boot or hose to the washer tub outlet to help prevent leaks and hose separation. Simple, durable hardware designed to restore a secure water-tight connection. What it does:

• Fastens the drain boot or outlet hose to the tub outlet to stop leaks at the connection.
• Keeps the drain hose or boot from slipping off during the wash cycle.
• Restores a tight, stable seal after worn or damaged clamps cause leaking.
• Works with the tub outlet/boot assembly to maintain normal drain flow.

• One tub outlet clamp.

• Disconnect power to the appliance before beginning any repair.
• Turn off water supply and drain any remaining water from the tub to avoid spills.
• Use appropriate pliers or a screwdriver (depending on clamp type) to remove the old clamp and secure the replacement.
• Inspect the boot/hose and tub outlet for damage; replace damaged components as needed for a reliable seal.

This small replacement clip secures the draining hose to the appliance, helping keep the hose in the correct position and preventing kinks, rubbing, or unintended movement that can cause leaks or drainage issues. What it does:

• Holds the draining hose in place to prevent sagging or rubbing against sharp edges
• Helps maintain proper hose routing for reliable draining
• Reduces the risk of hose chafing that can lead to leaks
• Simple mechanical part — no electrical function

• Disconnect power and water supply to the appliance before starting any work
• Locate the draining hose routing and remove the old clip, if present
• Snap the new clip onto the hose and secure it to the frame or mounting point until it clicks
• Inspect the hose path after installation; ensure the hose is seated and not kinked

This drain inlet hose carries wastewater through the washer's internal drain path during drain and spin cycles. Replacing a cracked, kinked, or leaking hose helps restore proper draining and protect floors and nearby components from water damage. What it does:

• Routes drain water between internal components to the drain outlet
• Maintains a sealed flow path to help prevent leaks
• Common symptoms: water on the floor during/after draining, standing water left in the tub, visible cracks/bulges/kinks on the hose
• May clog with debris, restricting flow and causing slow or no drain

• 1 drain inlet hose

• Unplug the washer and shut off water supply before servicing
• Have towels or a shallow pan ready; residual water may spill when hoses are removed
• Note hose routing and clamp positions; ensure the new hose is fully seated and not twisted or kinked
• After installation, run a quick drain/spin and check all connections for leaks

This retaining clamp secures wiring, hoses, or small assemblies to keep them routed and stable, helping prevent rubbing and vibration that can lead to wear or intermittent issues. Use it to replace a broken or missing clamp. What it does:

• Holds wires, hoses, or tubing in place to prevent contact with moving parts
• Reduces vibration and rattling by keeping components secure
• Prevents chafing that can cause insulation wear or exposed wiring
• Restores proper routing after repairs or part replacement

• Disconnect power (and water if applicable) before accessing internal components
• Use appropriate hand tools; avoid over-tightening which can damage the clamp or secured part
• Inspect surrounding wiring/hoses for damage and replace if needed

This drain hose assembly carries wastewater from the washer to the household standpipe or laundry tub. Replacing a cracked, kinked, or leaking hose helps restore proper draining and reduces the risk of water on the floor. What it does

• Routes drain water from the pump to the standpipe or laundry tub
• Helps maintain proper flow during drain/spin cycles
• Addresses leaks behind or under the washer caused by a damaged or loose hose
• Can help resolve slow or incomplete draining due to kinks, splits, or blockages

• Includes 1 drain hose assembly

• Unplug the washer and turn off water supply; have towels or a pan ready for residual water
• Move the appliance for access; note original hose routing and connection points
• Transfer and securely tighten any existing clamps/connectors; push hose fully onto fittings
• Route without sharp bends; secure outlet in the standpipe or sink and test for leaks

This stop-drain hose routes and drains water from the appliance to the drain or pump, helping prevent standing water and improper drainage. Replaces a worn, cracked, or leaking drain hose to restore proper water flow. What it does

• Channels discharged water from the appliance to the drain/pump assembly.
• Stops leaks caused by split, brittle, or collapsed hose sections.
• Helps restore normal draining when water pools in the tub or cabinet.
• Reduces the chance of water damage from a failed hose connection.

• Disconnect power and shut off the water supply before beginning any work.
• Remove old hose and inspect fittings; replace clamps if corroded or damaged.
• Route hose without sharp bends or kinks and secure with the factory clamps or equivalent.
• After installation, run a short cycle and check all connections for leaks.

The Pump Drain is an OEM part for GE washing machines. This component is responsible for removing water from the washer drum during the drain cycle, ensuring that the water is efficiently expelled from the machine. The pump drain plays a crucial role in the washing machine's ability to complete its cycles and maintain optimal performance.

Over time, the pump drain can become clogged, worn out, or damaged due to regular use or foreign objects obstructing the pump. Common causes of a bad pump drain include buildup of debris, wear and tear on the pump mechanism, or blockages from items accidentally left in pockets.

Symptoms of a bad pump drain include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• The washer stopping mid-cycle due to drainage issues
• Water leaking from the bottom of the washer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Includes 12 screws.

This pump and pressure hose harness connects the dishwasher pump to the pressure-sensing system, routing the hose and electrical connector so the drain/pump assembly can detect water level and operate reliably. What it does

• Routes the pressure-sensing hose from the sump to the pressure switch so water level is detected correctly.
• Provides the connector/harness interface for the pump circuit to ensure secure electrical connection.
• Helps prevent false water-level readings that can cause cycle errors or improper filling/draining.
• Commonly installed when the pressure hose is cracked, disconnected, or the pump connector is damaged.

• One pump and pressure hose harness assembly (hose and connector attached).

• Disconnect power and water supply before starting any repair.
• Handle connectors and hose gently; avoid pulling on wires—release any retaining clips before removal.
• Ensure the hose seats fully on the pressure switch nipple and is secured with the factory clip or clamp.
• After installation, power up and run a short diagnostic or quick cycle to confirm proper fill/drain operation and no leaks.