White Westinghouse Refrigerator Parts

This filter wrench is a ring-style tool used to loosen or tighten a refrigerator's water filter housing or canister. It provides extra leverage to free a stuck filter cup and helps ensure an even, secure reinstallation.

• Provides leverage to loosen a stuck water filter housing/cup
• Assists with secure, even tightening during reinstallation
• Useful when the housing is difficult to turn by hand
• Helpful in tight spaces where hand access is limited

• Turn off the water supply and dispense water to relieve pressure
• Position the wrench around the filter housing/cup; turn counterclockwise to loosen
• After replacing the filter, tighten the housing until snug—do not overtighten
• Restore water supply and check for leaks

This front shelf trim replaces a damaged or missing front edge on your refrigerator shelf. It restores a secure, finished lip that supports the shelf and helps keep items and small spills from sliding out.

• Attaches to the front edge of the shelf to provide a finished lip and added support
• Helps contain minor spills and prevents items from sliding off the shelf
• Resolves issues like cracked, warped, or missing trim and a loose or unstable shelf edge
• Common symptoms: broken or chipped trim, loose/missing front edge, shelf not seating or holding properly

• Remove food, lift out the shelf, and place it on a flat work surface
• Release the old trim by disengaging tabs and sliding/pulling it off
• Align the new trim with the front edge and press firmly until fully seated
• Handle shelf components carefully; wear protective gloves and disconnect power if working near internal electrical parts

This ice container deflector attaches to the ice bucket assembly and guides cubes toward the dispenser chute. Replacing a cracked or missing deflector restores proper ice flow and helps keep ice from spilling inside the freezer during dispensing.

• Directs ice from the bucket into the dispenser chute/crusher path
• Helps maintain consistent dispensing and minimizes stray ice inside the freezer
• Replace if cracked, warped, or missing
• Symptoms include erratic dispensing, ice spilling or jamming, or a visibly damaged/missing guide on the ice bin

• Disconnect power before servicing; remove the ice bucket
• Position the new deflector in the original location; reuse existing screws/clips if applicable
• Ensure the curved face points toward the dispenser chute
• Reinstall the ice bucket, restore power, and test ice dispense

This refrigerator shelf restores a flat, sturdy surface for storing food and containers. Replace a broken or missing shelf to regain capacity, keep items organized, and help prevent spills inside your appliance.

• Provides a level platform to hold groceries and containers
• Helps organize contents and maximize usable space
• Replaces damaged, bent, or missing shelves
• Common symptoms: cracked/broken shelf, wobbling, items tipping, reduced storage capacity

• Empty the area and wear gloves; handle carefully to avoid injury or damage
• Align the shelf with the side supports and slide or lower it into place
• Ensure it's fully seated before loading; distribute weight evenly

This compressor kit is made to be used with freezers and refrigerators by several manufacturers. It includes the compressor as well as all small parts associated with it. The compressor is a component that helps move the refrigerant throughout the appliance's system. Temperature sensors indicate when the compressor should run. If the compressor is damaged, it may make strange noises, no longer cool properly, or could begin to overheat.If any of these issues are present, the compressor should be replaced. First, make sure the refrigerator is not connected to a power source. Remove perishable items from the appliance and place them in an icebox, cooler with ice, or another refrigerator. Locate the compressor on the back of the appliance by removing the metal guard. Remove the wire between the compressor and the capacitor before taking off the compressor. Replace this part with the new one by connecting it to the wire and reassembling the appliance.This is a compressor kit for use with refrigerators and freezers made by Crosley, Electrolux, Westinghouse, Frigidaire, Kelvinator, Tappan, and Gibson. It is sourced directly from the manufacturer and sold as a single part. This is a genuine OEM replacement part.

This is a factory replacement screw fastener used to secure components in your appliance. It restores a tight, rattle-free fit for panels, brackets, and trim when an original screw is missing, stripped, or corroded.

• Secures panels, brackets, and trim to the appliance cabinet or liner
• Replaces a missing, stripped, or rusty screw
• Helps eliminate looseness, vibration, or rattling components
• Maintains proper alignment and a clean, factory fit

• Unplug the appliance before servicing; if near water lines, shut off the supply
• Match to the original and install in the same location/orientation
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Keep and reuse any original washers or spacers if present

This sliding basket replaces a damaged or missing freezer drawer basket to restore organized, pull-out storage and easier access to frozen items. It provides stable support for stored food and helps keep contents contained while sliding. What it does:

• Provides pull-out storage and organization for frozen foods.
• Restores drawer function when the original basket is cracked, broken, missing, or catches.
• Keeps items contained and easier to reach than loose stacking on shelves.
• Improves visibility and access to stored frozen goods.

• Always unplug the appliance and remove food/ice before starting any repair.
• Remove the old basket per the appliance service instructions and slide the replacement into the existing rails.
• Basic hand tools may be needed; retain original clips or fasteners if present.
• Verify fit by part number and appliance model before installation.

This actuator replaces the ice dispenser door motor that opens and closes the dispenser door so ice can drop into your cup. Restores proper door movement to help prevent ice blockages and missed dispenses. What it does:

• Drives the dispenser door to open and close when the dispenser is activated.
• Allows ice to release into the cup while keeping the dispenser sealed when idle.
• Common symptoms: dispenser door won't open, ice not dispensing, clicking or humming from the door area.
• Replaces a failed or intermittent dispenser door motor to restore normal dispensing action.

• Disconnect power to the appliance before beginning any repair.
• Replacement typically requires removing the inner dispenser/door panel; use common hand tools and keep track of fasteners.
• Inspect door linkage and wiring harness for damage when replacing the actuator.

The product featured is a Frigidaire refrigerator compressor. The compressor is a vital component for the cooling and freezing process of a refrigerator. A compressor works together with the evaporator in providing the cold air needed to keep everything at the desired temperature. When a compressor fails, this could have an effect that calls for an emergency repair. Losing the compressor function means the refrigerator stops getting cold in both compartments. Prolonging the repair could mean the loss of all the food items stored inside. A faulty compressor may become very loud when it operates. Users may hear a slight clicking sound on a compressor that's entirely out of commission. This is the relay clicking in an attempt to power the compressor. If a compressor does go out, keep the doors of the freezer and refrigerator shut. There's a chance the food can be salvaged if repairs take place fast enough. This compressor is a genuine OEM product and is sourced directly from the manufacturer and is only available as an individual component. Frigidaire, Kenmore, and Maytag refrigerators can be repaired with this component.

This is one endcap. Order quantity needed.

This refrigerator bracket and bushing assembly secures a moving component and provides a stable wear/pivot surface for smooth operation. Replace it when the original parts are worn or broken and causing looseness, scraping noises, or poor alignment.

• Provides a mounting point and bearing surface for rotational or sliding movement
• Helps maintain alignment and smooth, quiet operation
• Can help address wobble, scraping/binding, or a component that sags or sits out of position
• Replace if the bracket is bent/cracked or the bushing is worn/missing

• Disconnect power before servicing; turn off water supply if working near dispenser lines
• Support the attached component while removing fasteners; note the original orientation
• Transfer any spacers/clips from the old parts if present and tighten fasteners evenly
• After installation, verify smooth movement and proper alignment

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

Bottom air diffuser directs cold air into the refrigerator's lower cabinet to help maintain even temperatures and reduce warm spots. Replacing a damaged diffuser restores proper airflow and helps the fresh-food section cool more consistently. What it does:

• Redirects cold air from the cooling channel into the refrigerator's lower cabinet for balanced cooling.
• Helps reduce warm spots and uneven temperatures in the fresh-food area.
• A cracked, broken, or missing diffuser can lead to restricted airflow and inconsistent cabinet temperatures.
• Seats into the lower air channel and secures with factory tabs or fasteners; inspect mounting tabs for damage.

• Disconnect power to the appliance before performing any service.
• Remove shelves and drawers as needed for access; work carefully around evaporator/air channels.
• Gently release and re-seat plastic tabs or remove fasteners; avoid forcing parts to prevent breakage.
• If tabs are damaged, replace them or consider replacing adjacent vent components to ensure a secure fit.

This replacement water tube routes water within the refrigerator's internal water system. Installing a fresh, intact tube helps stop leaks and restores reliable water flow to the dispenser and ice maker. What it does:

• Carries water between components such as the inlet valve, reservoir, dispenser, and ice maker
• Maintains a sealed, kink-free path for proper flow and pressure
• Common signs of failure: leaks or puddling, weak or no dispenser flow, ice maker not filling, brittle or discolored tubing

• One tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the original routing; take photos to match length and path
• If trimming, cut ends square and fully seat into the existing push-to-connect or compression fittings
• Restore water and check all connections for leaks before powering the unit back on