White Westinghouse Relay, Overload, Capacitor

This compressor start relay (PTC) briefly powers the compressor's start winding to ensure reliable start-up. Replacing a failed relay can stop repeated clicking and help a non-starting compressor restore normal refrigerator cooling.

• Provides a timed, resistance-based boost to the compressor's start winding, then drops out of the circuit
• Common symptoms: compressor hums then clicks off, frequent clicking from the rear, warm fridge/freezer, intermittent cooling
• Mounts directly on the compressor terminals; works with the separate overload protector and, if equipped, a run capacitor
• Visible signs of failure may include heat damage, burnt odor, or loose/rattling pieces inside the old relay

• Unplug the refrigerator and remove the lower rear access panel to reach the compressor
• Note wire routing and orientation; transfer any harness/retainer and seat the relay fully on the compressor pins
• If a run capacitor is present, discharge it before handling and reconnect to the same terminals
• Inspect the overload and connectors; replace any heat-damaged components

This electronic control board manages the appliance's user interface and core control functions, restoring reliable operation when the original board fails. It replaces a damaged or unresponsive control module to help regain normal appliance control. What it does:

• Sends and receives signals to operate timers, relays, and display functions.
• Controls user inputs and on/off sequencing for the appliance's systems.
• Common symptoms of a failing board: unresponsive controls, blank or erratic display, cycles not starting or stopping, or intermittent operation.
• Use this board to replace units exhibiting control or display faults that other components have not resolved.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Handle the board by the edges and avoid touching components; use an ESD strap if available.
• Verify wiring harness connections and fuses before and after installation.

This relay assembly helps start the refrigerator compressor so the cooling system can run reliably. It replaces a worn or failed start relay to restore normal compressor startup and reduce hard-start symptoms. What it does:

• Provides the initial start pulse to the compressor motor so the refrigeration cycle can begin
• Stops excessive current draw during startup to protect the compressor
• Commonly used when the compressor hums, won't start, or cycles on and off rapidly
• Helps eliminate starter-related clicking or failure-to-start issues

• Disconnect power to the appliance before inspecting or replacing the relay
• Handle electrical connectors carefully; ensure secure, correct reattachment
• Verify match to the existing relay and mounting before installation

This PTC starter helps the compressor start by briefly supplying the correct current at startup, restoring reliable cooling when the compressor struggles to kick on. Compact replacement for failed or weak start devices. What it does

• Provides a timed boost to the compressor start winding so the compressor can start reliably
• Commonly used when a refrigerator or freezer won't start or hums without running
• Helps prevent frequent hard starts that can overheat the compressor
• Passive solid-state design with no moving parts for simple, maintenance-free operation

• Disconnect power to the appliance before inspecting or replacing the starter
• Handle electrical connections carefully; install the starter in the same orientation and wiring position as the original
• If the compressor or start relay shows additional damage, replace those components.

This compressor start relay helps the refrigerator compressor start reliably so the appliance can maintain proper cooling. It replaces a failing start device to restore normal compressor startup behavior. What it does:

• Provides the initial boost to the compressor motor so it can start turning
• Commonly used when the compressor hums or won't start but power is present
• Can reduce repeated clicking or intermittent starts caused by a failed start device
• Works with the compressor's start circuit; does not replace sealed-system components

• One compressor start relay

• Disconnect power to the appliance before accessing electrical components
• Inspect associated start capacitor/overload if present; replace if faulty for reliable operation

This capacitor stores and releases electrical energy to help the refrigerator's compressor start and run smoothly. Replacing a weak or failed capacitor can restore reliable compressor startup and more consistent cooling performance.

• Provides the electrical boost/phase shift needed for compressor motor startup and steady operation
• Works with the start device to deliver proper current to the compressor
• Failure symptoms can include clicking or humming near the compressor, poor cooling, or short cycling
• May cause the compressor not to start after power interruptions when weak or failed

• Disconnect power before servicing any electrical component
• Safely discharge the capacitor before handling; avoid touching terminals
• Note wire positions and terminal markings; transfer leads one at a time to the matching terminals
• Secure the capacitor in its mounting/bracket to prevent vibration damage

This Temperature Controller regulates cooling by switching power to the compressor and related circuits to hold the set temperature. Replacing a failing controller restores accurate temperature control and reliable operation. What it does:

• Cycles cooling components to maintain the temperature you set
• Helps keep cabinet temperatures consistent for proper food storage
• Coordinates on/off operation to prevent overcooling or warm conditions
• Common failure symptoms: too warm or too cold, runs constantly or won't start, control/dial unresponsive

• 1 temperature controller

• Disconnect power before servicing—this is a line-voltage control
• Access the control area, label or photograph wire positions, and move wires one at a time to the new controller
• Reuse existing mounting hardware and any knob/overlay as applicable
• After install, set to mid setting and allow up to 24 hours for temperatures to stabilize

This electronic control board is the refrigerator's main circuit board that manages temperature, defrost and user controls—restoring responsive control functions and resolving erratic or non-working control behavior. What it does:

• Controls compressor, fans and defrost cycles by sending signals based on sensor inputs
• Manages user interface commands and display response
• Can stop fridge cooling or cause incorrect temperatures when failing
• May cause intermittent operation, no display response, or failure to complete defrost cycles

• Disconnect power to the appliance before starting any work to avoid electrical shock
• Handle the board by its edges and avoid touching components or connector pins
• Verify connector orientation and seating; replace exactly like-for-like to ensure compatibility

This compressor start relay helps the refrigerator compressor start and run more reliably, restoring proper cooling performance and preventing frequent hard starts. Fits compatible Frigidaire-style compressors and connects at the compressor terminal block. What it does:

• Provides the initial boost to spin the compressor motor during startup
• Helps prevent the compressor from stalling or failing to start
• Can reduce clicking, humming, or a fridge that runs but does not cool
• Works with the compressor's start circuit to engage the motor quickly

• Disconnect power to the appliance before inspecting or replacing the relay
• Access the relay at the compressor (usually mounted on the compressor body); note terminal positions before removal
• Replace only with the exact relay specified by the manufacturer; secure all connections and wiring