White Westinghouse Guard, Shield, Barrier Parts

This splash shield kit is an OEM replacement part that prevents water from spraying beyond the door seal in Frigidaire dishwashers. The kit measures 1.5 inches in length, 0.5 inches in width, and 1.7 inches in height.  This kit is located on the front lower corners of the dishwasher tub. If your dishwasher is leaking due to a damaged or worn-out splash shield, the kit provides a reliable replacement.

Symptoms of a bad splash shield kit include:

• Stains or mineral deposits on surrounding cabinetry   
• Puddles or drips developing outside the dishwasher tub 
• Reduced cleaning ability due to unredirected spray patterns
• Damage, cracks or missing sections of splash shielding 

Causes can be normal wear from extended use breaking down barriers over time. Proper shield alignment is needed to effectively direct spray inside the tub.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This replacement water tube routes water within the refrigerator's internal water system. Installing a fresh, intact tube helps stop leaks and restores reliable water flow to the dispenser and ice maker. What it does:

• Carries water between components such as the inlet valve, reservoir, dispenser, and ice maker
• Maintains a sealed, kink-free path for proper flow and pressure
• Common signs of failure: leaks or puddling, weak or no dispenser flow, ice maker not filling, brittle or discolored tubing

• One tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the original routing; take photos to match length and path
• If trimming, cut ends square and fully seat into the existing push-to-connect or compression fittings
• Restore water and check all connections for leaks before powering the unit back on

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

A replacement protective shield that covers and protects internal appliance components from debris, moisture and incidental contact. Restores protection to damaged or missing shields to help maintain safe, reliable operation. What it does:

• Covers and protects wiring, connectors or nearby parts from accidental contact and debris
• Helps prevent moisture or food particles from reaching sensitive components
• Replace if the shield is cracked, warped, missing or allows exposed parts
• Reduce rattles or contact-related noises caused by loose or damaged shields

• Shield

• Disconnect power to the appliance before starting any repair
• Use care around sharp edges; wear gloves and eye protection
• Remove fasteners holding the old shield; reuse or replace screws as specified by the manufacturer

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This replacement overflow shield directs excess water away from sensitive components to help prevent leaks and water damage in the appliance. It restores proper drainage protection when the original shield is cracked, warped, or missing. What it does:

• Channels overflow or stray water away from critical areas to reduce risk of leaks
• Replaces damaged, cracked, or missing overflow shielding
• Helps maintain proper drainage pathways and component protection
• Commonly used when you see water pooling or dripping near the shielded area

• One overflow shield

• Inspect surrounding seals and fasteners; replace any that are damaged before installing the new shield
• Installation typically requires basic hand tools; secure the shield in the original mounting points
• Disconnect power to the appliance before starting work and restore power only after reassembly