White Westinghouse Control Board

The Clock is an OEM part for Frigidaire ovens and ranges. It is the central electronic component that regulates and monitors oven functions such as bake, broil, convection, temperature controls, and timers.

Causes can be failures in the integrated circuitry, damaged connectors or traces on the board, or water or other environmental damage over time.

Symptoms of a clock include:

• Failure of oven elements to heat properly
• Unresponsive or inaccurate temperature displays
• Irregular timed baking or errors flashing
• Problems with convection or baking modes
• Power issues such as the oven not turning on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Oven Control Board Clock is an OEM part for Frigidaire wall ovens and ranges. It is a component mounted directly to the main control board that regulates time settings for the various oven functions.

Causes of a bad control board clock can include faulty wiring, moisture damage from accidents improper cleaning, or natural age-related deterioration.

Symptoms of a bad control board clock include:

• Inaccurate or inconsistent time display
• An inability to set or maintain timer functions
• Random clock resetting or non-functionality
• Issues initiating timed cooking modes

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This is a motor control board for a washing machine. It comes with the board, tape, bracket, and screw mounted on control. In most cases, this part is located on the bottom of the appliance near the drive motor. The purpose is to control the speed of the drive motor. It also works to determine the direction of the tumble and spin actions while a cycle is in process. If the washing machine is pumping but does not spin, this is often the result of a malfunctioning motor control board.If the motor control board has gone bad, it should be replaced. To replace it, make sure the washer is unplugged or the circuit breaker has been turned off. Pull the washer away from the wall, remove the knobs from the front and screws from the back, and lift the control panel. This offers access to the motor control board, which should be removed so the new part can be installed.This motor control board is made for use with washing machines by Electrolux, Frigidaire, Crosley, and Kenmore. It is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Washer Timer is an OEM part for Frigidaire washing machines. It controls the sequence of operations in the washing machine, including filling, washing, rinsing, and spinning. By managing the timing of these cycles, the timer ensures the washer operates efficiently and effectively.

Causes of a bad washer timer can include electrical malfunctions, wear and tear from regular use, or physical damage to the timer mechanism. Power surges, exposure to moisture, and accidental impacts can also lead to timer failure.

Symptoms of a bad Washer Timer include:

• Washer not advancing through cycles
• Machine getting stuck on a single cycle
• Incorrect timing for washing, rinsing, or spinning
• Washer not starting or completing a cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Defrost Control Board is an OEM part for Frigidaire refrigerators. This board manages the defrost cycle by controlling the activation of the defrost heater and the monitoring of the freezer's temperature. 

Over time, the defrost control board can fail due to electrical issues, wear from continuous use, or damage from power surges. 

Symptoms of a bad defrost control board include:

• Excessive frost buildup in the freezer compartment
• The refrigerator not cooling properly
• The defrost heater not activating
• Frequent cycling on and off of the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This dryer timer controls and advances the cycle you select, routing power to the correct components and shutting the dryer off at the proper time. Replacing a worn timer restores consistent cycle timing and end-of-cycle shutoff.

• Controls cycle selection and duration
• Advances the dial through the program and turns the dryer off at the end
• Routes power to dryer components at the correct times during the cycle
• Signs of a failing timer may include: cycle not advancing, running indefinitely, stopping early, or erratic timing

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the control knob and access the console to unmount the old timer
• Label or photograph wiring; move terminals to the new timer one at a time to avoid miswiring
• Align the timer shaft with the dial, secure the timer, and test operation before reassembly

This dryer timer is the cycle control that advances your dryer through Timed and Auto Dry settings. Replacing a failed timer restores proper cycle progression, start/stop, and end-of-cycle shutoff.

• Advances the cam and internal contacts to move the dryer through heat, motor, and cool-down steps
• Governs run time on Timed Dry and Auto Dry cycles
• Routes power to the correct circuits in sequence; a failed timer may not advance or may stop early
• Common symptoms include timer knob not moving, dryer running indefinitely, or not starting on certain settings

• Disconnect power; for gas models, also shut off gas
• Remove knob/dial, open the console, and unmount the timer
• Label or photograph wiring; transfer wires one at a time to the new timer
• Reassemble and test both a Timed Dry and an Auto Dry cycle

This part is an control board that's intended to replace a faulty or broken control board in washing machines. Over time, the control board can become worn, corroded, detached, or otherwise rendered ineffective, which may make it difficult or impossible for the user to manage the washer's functions and cycles. Before replacing this part, ensure the washing machine is entirely disconnected from the power and water source. Work gloves should be worn anytime a repair or replacement is attempted.This is a genuine OEM part made by Frigidaire and has been sourced directly from the manufacturer. This part is suitable for use on a variety of washing machine models that manufactured by Frigidaire, Electrolux, Westinghouse, and Kelvinator. It is a genuine OEM part and thus is manufactured from high-quality, durable, non-corrosive materials and is only sold individually.

This is a washer timer. The timer is used to control how long different elements of the wash cycle take, including filling, soaking, washing, spinning, and rinsing. If the timer is not working properly, the machine may cease to function properly. It could take more time to wash, or the machine might never stop spinning.Parts of the timer, such as the pins or motor, could break, corrode, or wear out. Unplug the washer before they start the repair. It's also a good idea to wear gloves for safety.This washer timer is compatible with washers from Frigidaire, Crosley, and White-Westinghouse. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually.

This mechanical defrost timer advances the refrigerator's defrost cycle to help prevent excessive frost and ice buildup on the evaporator. Replaces a failed timer to restore automatic defrosting and more consistent cooling. What it does:

• Cycles the refrigerator between cooling and defrost modes on a timed schedule
• Initiates heater and compressor changes to melt frost accumulation
• Common symptom: heavy frost or ice on the evaporator or inside freezer compartment
• Common symptom: unit runs continuously or cooling performance is inconsistent

• Disconnect power to the appliance before any repair to avoid shock
• Locate timer (behind kick plate, control panel, or at rear) and note wire positions or take a photo before removing
• Swap the old timer for the replacement and reconnect wires to matching terminals

This is a refrigerator control board. The function of the control board is to effectively control all of the refrigerator's functions. These functions could include cooling the fridge, defrosting, dispensing, and even lighting.In the event that any of the functions of the refrigerator stop working correctly, the control board could be the culprit. If the buttons on the unit are pressed and nothing happens, it's likely that the control board is faulty. For example, the refrigerator may not be cooling, defrosting, the lights might not work, or the ice and water will not dispense. If this is the case, this is a high-quality replacement part. Make sure to unplug the refrigerator from the electrical outlet before replacing this part. This specific control board is compatible with refrigerators that are manufactured by the Frigidaire and Crosley brands. It is sold individually and sourced straight from the manufacturer.

Made to be used on washing machines, this part is a timer. This component controls the electrical parts and the duration of time of the washing machine's cycles. It controls the operation of the washing machine, including each of the cycles.When the timer will not advance, the washing machine could become stuck in a cycle and run constantly without stopping. The washing machine may not advance through the particular cycle like the washing, rinsing, or spinning and could get stuck on one of the cycles. It's important to unplug the washing machine from the electrical outlet before attempting to repair or replace any parts. The replacement process is fairly easy and takes about 15 minutes to complete.This timer is compatible with washing machines that are manufactured by the Frigidaire, Gibson, Kenmore, and White-Westinghouse brands. This part is sold individually and is sourced straight from the manufacturer itself.