White Westinghouse Washer Clip Or Clamp

This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.

• Holds a hose firmly on a pump, tub, dispenser, or valve outlet
• Maintains clamping force to help minimize leaks at the joint
• Helps keep hoses from slipping off during operation
• Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp

• Disconnect power and shut off water supply before servicing
• Place a towel or pan to catch residual water at the connection
• Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
• After reassembly, run a short cycle and check for leaks

This retaining ring secures a shaft or component in-place to prevent axial movement and wear, restoring proper alignment and reducing noise or wobble. It's a small, durable replacement part for assemblies that use a snap-style ring. What it does:

• Holds shafts, bearings or components axially in their mating grooves to prevent shifting.
• Stops rattling, grinding, or excessive play caused by a worn or missing ring.
• Keeps assemblies aligned to reduce premature wear on surrounding parts.
• Provides a simple replacement solution when the original ring is bent, broken, or lost.

• Disconnect power and/or water and remove any panels needed before starting work.
• Use snap-ring pliers or the manufacturer-recommended tool to safely remove and install the ring.
• Inspect grooves and mating surfaces for damage or debris and clean before installing the new ring.
• Wear eye protection and keep fingers clear—snap rings can spring out during removal or installation.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

This spring clamp secures the refrigerator door bellow to the cabinet, helping hold the bellow in place for a tighter seal and consistent door alignment. A simple replacement that restores proper bellow retention. What it does

• Holds the door bellow tightly to the cabinet or door frame
• Prevents bellow from pulling away or bunching during door use
• Helps maintain a consistent seal to reduce drafts at the door edge
• Works where a worn or damaged clamp allows visible gap or misalignment

• Basic hand tools usually required; inspect surrounding bellow for wear before installing
• Wear gloves and eye protection; spring clamps can snap back during removal/installation
• If clamp is difficult to seat, ensure bellow is properly positioned and not torn
• Replace damaged bellows or additional fasteners to ensure a complete seal

A small replacement retainer clip used to secure interior trim or components so panels and shelves stay in place. Replacing a worn or broken clip restores a snug fit and reduces rattling or loose parts. What it does

• Holds trim, panels or small components in place to prevent shifting
• Prevents rattling and keeps parts aligned for proper operation
• Replaces cracked, broken or missing clips that allow parts to sag or fall
• Works wherever the OEM clip design is specified for a secure snap-fit

• Clip

• Disconnect power before servicing appliances with electrical components
• Remove surrounding trim or components carefully to access clip location
• Press or snap the clip into place; avoid forcing to prevent damage
• Keep small parts away from children and pets during installation

This clamp secures flexible hoses and small-diameter tubing to fittings, helping prevent leaks and keeping connections tight for reliable appliance operation. Use it where a compact, durable clamp is required for water or drain lines. What it does:

• Holds hoses or tubes firmly to inlet/outlet fittings to reduce leaks
• Prevents hoses from slipping off during normal use or vibration
• Helps maintain proper fluid flow by keeping connections sealed
• Useful for water lines, drain hoses, and small appliance tubing

• One clamp

• Turn off and unplug the appliance and shut off water supply before starting
• Inspect the hose and fitting; replace any damaged hose before installing clamp
• Position clamp over the hose/fitting and tighten evenly for a snug fit without crushing the hose

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

This small retainer clip secures trim, panels or wiring harnesses so components stay aligned and rattle-free during use. It's a simple replacement that restores proper fit and helps prevent loose parts from shifting or rattling. What it does

• Holds panels, trim or harnesses in place to prevent movement and vibration
• Stops rattling or buzzing caused by loose fasteners or trim
• Keeps electrical wires routed and secured to reduce strain
• Restores proper fit where a broken or missing clip allowed gaps or play

• Basic snap-in installation; remove trim or access panel as needed to reach the clip location
• Inspect mating holes and surrounding plastic or metal for damage before installing
• Use moderate finger pressure or appropriate pliers — avoid over-forcing to prevent breaking the new clip
• Disconnect power if working near electrical components or wiring

A small OEM fastener used to secure appliance panels and trim for a clean, stable fit. Replaces a worn or missing retainer to prevent rattling and keep exterior parts aligned for normal operation and appearance. What it does:

• Secures panels, trim, or small components to the appliance frame
• Helps prevent vibration noise and loose or sagging panels
• Restores proper alignment of exterior pieces after repair or removal
• Useful when a broken or missing retainer causes rattling or gaps

• Typical installation requires basic hand tools; tighten until snug—do not overtighten
• Turn off power to the appliance before accessing interior components when required
• Keep small parts away from children and pets during repair