White Westinghouse Washer Parts

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

• Spins slowly
• Burning smell
• Pumps but will not spin
• Will not agitate

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

• Leaking

Fixed by replacing the washer door seal "Bellows". Once again AppliancePartsPros comes through with the right part at a great price. It took quite some time to install because putting the inside spring back on the bellow was difficult so I needed to remove the top and front door of the washer to get better access. A set of 3 or 4 plumbing clamps are highly recommended to get that spring back on (I went to the store and bought some). If you search YouTube about replacing the bellows on your... Read more

• Won't start
• Touchpad does not respond

Replaced old knob with new knob Read more

• Will not drain

Replace the drain pump after watching a video demonstrating the process. The washing machine had run properly and emptied, so I was surprised how much water remained in the pipe after disconnecting the old pump. Plan on having 2-3 large towels underneath before removing it. The most difficult part (and most irritating) was replacing the intake and outtake hoses with the existing spring clamps. The drain hose into the pump took almost twenty minutes to attach properly. If the hardware store was... Read more

This was a fairly easy fix. The only problem I had was that the cover over the retaining nut was difficult to pull off. I changed to a larger pair of pliers and put a little more muscle to it and it popped right out. There was a little corrosion on the shaft that needed to scraped off for the new agitator to slide on easily but after that was gone the new part slid on and with some downward pressure it seated in. Read more

• Spins slowly

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

Replaced the rear drum bearing assembly and the front top felt that the drum rides on and since I has it apart installed a new belt. Simple to do and takes very little time! Read more

Got online and searched for part by washer model number. Found AppliancePartsPro.com. They listed diagram of part. I ordered it online and received it next day with no extra charge for fast delivery. My husband attached cosmetic drawer cover to detergent drawer part we ordered in a few minutes. It fits and is working! Speedy service was appreciated. Read more

Replaced springs and shocks. Read more

This was the motor control board (also called the speed control board, motor control unit, or MCU in various places across the web). The repair was straightforward, except for two complications. First the old part was difficult to access in this model washer (Frigidaire Gallery Series front load washer). Instead of being easy to reach on the left side where there was space, it was sort of behind the actual motor on the right side of the housing. I spent some time trying to figure out... Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more