Kenmore / Sears Dryer Burner & Related Parts

• Timer will not advance
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

• No heat or not enough heat
• Takes too long to dry

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

Ordered conversion kit from Appliance Parts Pros.com and installed it myself. Most difficult part of the repair, was the removal of the front casing of the dryer to access the location of venturi tube to be changed out. The instructions were helpful, but not specific enough for my dryer. Once the casing was off, the job was not too difficult - you will need a set of short screwdrivers to remove the burner flange and close the pressure adjustment screw, normal length screw drivers will come into... Read more

Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more

It took less then 15 min. Read more

I'm not an appliance mechanic and have never worked on a dryer before, but I have worked as an instrument technician and lightly dabbled in HVAC repairs. We moved from natural gas to a new home with propane, so purchased this kit to make the conversion. In my mind I thought it would be fairly quick and easy, change a few fittings, etc, but realized upon reading the instructions that I needed to disassemble most of the dryer. The work was straightforward but since this was my first time... Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more

Unfortunately my first repair attempt (replacing the Gas Valve Coils) failed so I decided to replace the entire Burner assembly. From a cost/time point of view the Burner assembly is a better value than just buying the Gas Valve seeing as you don't have to disassemble/reassemble most of the existing Burner (to get to the Gas Valve) *and* you get a new Igniter!! The most annoying thing about the repair is accessing the screw that clamps the gas pipe to loosen it :-(... Read more

Removing cabinet panels to access burner was the major challenge since every one seems to be different. This one, two screws at back allowed top to raise and be removed, Two more screws at front and two cables disconnected removed control panel. The door panel was not quite as obvious, The two screws at top sides and two at very bottom edge were removed. Then by trial, I removed screws around door edge until panel was loose. I removed a couple extra; but the whole door and panel lifted off.... Read more

I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only... Read more

Valve (or a component on it) was slowly leaking gas. I was able to easily replace the entire gas assembly with this order. Item was mostly pre-assembled, and contained all parts needed, including new igniter and coils. Read more

I decided the problem was with the gas valve and I found the part on your web site. I ordered it and received the part in 3 days. I replaced the valve and the dryer works like new! This also gave me an opportunity to vacuum out the dust/lint that collects in and around the dryer. Read more

After watching the video, I replaced the gas valve. Read more

Ordered the gas assembly valve Read more