Whirlpool Drawer, Shelf, Pan

The Utility Pan is an OEM part for Whirlpool refrigerators. It is responsible for providing additional storage space in the refrigerator through a sliding drawer.

The utility pan is designed with smooth roller glides to allow for easy and quiet opening and closing of the drawer. It provides a flexible storage solution for taller or bulkier items that may not fit elsewhere in the refrigerator.

Causes of a bad utility pan can include worn glides or rollers resulting in difficult opening/closing, or damage to the assembly components themselves through heavy use over time.

Symptoms of a bad utility pan include:

• The drawer failing to fully close or open
• Items inside tipping over due to uneven motion
• Noise or scraping sounds when operating the drawer
• Physical damage or deformation of the assembly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Restore tidy storage in your refrigerator's deli/pantry drawer with this Pantry Drawer Divider. Replacing a cracked or missing divider keeps foods separated and helps the drawer slide and close properly without contents shifting or tipping.

• Separates and stabilizes items within the deli/pantry drawer for better organization
• Helps prevent contents from sliding and causing the drawer to bind
• Restores proper fit when the original divider is cracked, warped, or missing
• Typical symptoms: divider falls out or won't stay positioned; difficulty keeping foods organized

• Disconnect power to the refrigerator and remove items from the deli/pantry drawer
• Fully extend and lift out the drawer as directed in your user manual
• Align the divider with the molded slots/grooves and press or slide into place until secure
• Reinstall the drawer and verify smooth operation; do not force parts

This replacement bracket provides a secure mounting point for a designated component in your appliance. It keeps parts properly supported and aligned, helping the unit operate smoothly without vibration or shifting.

• Supports and anchors a specific part or assembly in the correct position
• Helps prevent vibration, rattling, and premature wear from movement
• Maintains alignment for consistent, reliable operation
• Replace if bent, cracked, or missing; symptoms can include loose components or unusual noise

• Disconnect power; shut off water or gas supply if applicable
• Access the bracket location per your model's service information and note the original orientation
• Transfer any screws, clips, or grommets from the old bracket to the new one
• Tighten fasteners evenly and verify alignment before restoring power

This control lever secures a refrigerator door shelf bin to the door frame so bins stay seated and stable during normal use. Replacing a broken or worn lever restores proper bin retention and reduces rattling or unexpected bin release. What it does

• Holds the door shelf/bin in place so it doesn't fall out when opening or closing the door
• Aligns and retains the bin on the door track for secure storage
• Stops bin-related rattles and noisy door operation caused by a loose or cracked lever
• Common symptom: bin falls out, won't stay seated, or rattles in the door

• One door bin control lever

• Remove food and take the door bin off the door before replacing the lever
• Inspect the bin and mounting area for damage; clean mounting surfaces if needed
• Lever typically snaps into the door mounting point; align and press until it clicks
• Disconnecting power is not required for most door-bin repairs, but follow all safety precautions and your model's service instructions

This mounting cup installs in the freezer liner to create a secure attachment point for the ice maker or its bracket. It helps keep the assembly stable and properly aligned so the ice maker mounts firmly and operates reliably. What it does:

• Provides the receiving anchor for the ice maker/bracket mounting screw
• Helps hold the ice maker level and reduces movement or vibration
• A worn, stripped, or missing cup can prevent the screw from tightening
• Common signs include a loose or sagging ice maker, rattling, or difficulty keeping the ice maker aligned

• 1 mounting cup

• Disconnect power and shut off the water supply before servicing
• Remove the ice maker to access the cup location
• Seat the cup fully into the liner opening, then reinstall the bracket/ice maker and mounting screw
• Do not overtighten; verify the ice maker sits level and clears the fill tube

This outer door trim replaces a cracked, faded or damaged decorative panel on the appliance door to restore appearance and help keep the door edge looking finished. It matches the original style and mounting points for a direct-fit replacement. What it does

• Covers the door edge and conceals the mounting area for a factory look
• Restores worn, chipped or discolored trim to improve appearance
• Helps maintain even door alignment by fitting to original trim locations
• Prevents rough or sharp trim edges from being exposed

• One outer door trim

• Use basic hand tools; part installs where the original trim was mounted
• Follow the appliance manufacturer's disassembly and reassembly instructions
• Disconnect power before starting work
• Wear gloves to protect hands from sharp edges during removal and installation

This trim pan is a molded replacement trim piece that restores the lower exterior appearance and helps channel minor drips away from the appliance base. It provides a clean, finished look and replaces damaged or missing trim. What it does:

• Replaces a cracked, warped or discolored lower trim that affects appearance
• Helps direct incidental moisture away from the cabinet base
• Restores the factory fit and finish at the appliance front/bottom
• Prevents sharp edges or gaps that can catch dirt or debris

• Disconnect power to the appliance before starting work to avoid electrical hazard
• Basic hand tools are typically required; remove fasteners or clips holding the old trim and snap or screw the replacement into place
• Handle plastic trim carefully to avoid scratching; align clips or tabs before applying pressure
• If you encounter unexpected corrosion or additional damage, stop and inspect for related repairs

This right-hand side adapter bracket secures the appliance cabinet or panel, restoring proper fit and stability. Replacing a damaged or missing bracket helps stop loose or misaligned panels and reduces rattling. What it does:

• Secures the right-side cabinet or panel to the chassis to maintain alignment and support.
• Helps eliminate panel movement, vibration and rattling that result from a cracked or missing bracket.
• Restores correct panel gaps so doors or drawers operate and close properly.

• Disconnect power (unplug or shut off breaker) before accessing the appliance.
• Remove the required access panels to reach the bracket; keep and reuse existing fasteners unless new hardware is specified by the model diagram.
• Transfer the bracket into position and fasten securely; check for proper panel alignment after installation.

This door shelf trim (retainer bar) snaps across the front of a refrigerator door bin to keep bottles and condiments secure. Replace a cracked or missing rail to restore safe storage and prevent items from falling when the door opens.

• Secures items on the door shelf/bin and helps prevent spills during normal use
• Replaces broken, cracked, warped, or missing trim that won't stay attached
• Helps the door close without interference from loose items
• Typical symptoms: items fall from the door bin; rail is loose, damaged, or missing

• Empty the door bin before servicing
• Release the old trim by disengaging the end tabs or clips; pull outward to remove
• Align the new trim with the bin slots and snap both ends in evenly—do not overflex
• Inspect the door bin for cracks or worn slots that could prevent a secure fit

This left-side adapter secures the appliance's panel components and helps maintain proper alignment for reliable operation. It's a direct replacement that restores fit and support where the original left-side adapter is damaged or missing. What it does:

• Replaces a worn or broken left-side adapter/bracket to restore panel alignment and support
• Helps prevent rattling, misalignment, or loose panels that can occur with a damaged adapter
• Fits the left side mounting points to secure adjacent panels and components
• Works as a structural support piece in the appliance's chassis assembly

• 1 left-side adapter

• Disconnect power and water before starting any repair
• Handle panels carefully to avoid bending; support panels while removing fasteners
• Use the original fasteners unless replacements are specified by the manufacturer

This replacement freezer bin is the removable drawer that stores frozen food and keeps items organized in the freezer compartment. It restores secure storage and easy access when the original bin is cracked, broken, or missing. What it does:

• Holds and organizes frozen food inside the freezer drawer area.
• Slides in and out on the freezer tracks for convenient loading and access.
• Prevents items from falling into lower compartments when installed correctly.
• Commonly replaced when the bin is cracked, warped, or no longer latches securely.

• Empty the freezer section and remove any ice buildup before installing.
• Align the bin with the tracks and slide it in until it seats; do not force.
• Handle carefully to avoid chipping or cracking the plastic edges.

Replacement left-side crisper pan cap that secures the refrigerator crisper drawer and helps keep the glass pan aligned. Restores a stable fit so drawers slide smoothly and produce sits level. What it does:

• Secures the left crisper pan to the refrigerator frame to prevent shifting and rattling.
• Helps keep the glass crisper pan aligned so the drawer opens and closes smoothly.
• Common symptom fixes: loose or uneven crisper drawer, rattling, or a pan that won't stay in place.
• Designed to match the original fit and function for the left-side crisper pan location.

• Always disconnect power or unplug the refrigerator before servicing.
• Remove the crisper pan to access the cap; follow your model's service manual for step-by-step instructions.
• Cap typically snaps or presses into position—if resistance is felt, stop and confirm alignment to avoid damage.
• Handle glass and sharp edges carefully; inspect surrounding rails/supports and replace additional damaged parts as needed.

This interior storage basket restores organized storage inside the appliance so food and containers stay contained and easy to access. It replaces a cracked, bent or missing basket to help keep shelves tidy. What it does

• Provides a removable container to organize and contain items inside the appliance.
• Keeps smaller items from shifting or falling through vents or shelf gaps.
• Replaces a warped, cracked or broken basket that can snag or allow spills.
• Helps maintain usable storage space and improves access to stored items.

• One interior storage basket

• Most baskets simply lift out and lift back in; check the cabinet rails or support tabs for proper seating.
• If screws or clips secure the basket, use the correct size driver and keep parts organized during removal.
• Disconnect power before servicing if working near electrical components or lights.
• Wear gloves to protect hands from sharp edges and support the basket during removal to avoid drops.

This wire shelf replaces a damaged or missing refrigerator shelf to restore stable storage and proper airflow in the fresh-food compartment. It provides a durable, easy-to-clean surface for storing food and containers. What it does

• Replaces a bent, rusted, or broken wire shelf to restore usable storage space
• Supports food and containers while allowing cold air to circulate for even cooling
• Helps prevent items from falling or shifting during door openings
• Fits onto existing shelf supports or slide rails for a secure fit

• One wire shelf as shown

• Remove all contents and unplug the refrigerator or turn off power at the breaker before starting
• Lift old shelf straight up or unhook from supports, then set replacement shelf onto the same supports or rails
• No special tools typically required; use gloves to avoid sharp wire edges
• Verify shelf is level and secure before returning food to the compartment

This replacement divider restores simple organization inside the refrigerator by separating items on a shelf or bin to reduce shifting and spills. It replaces a cracked, broken or missing factory divider and helps keep stored items upright. What it does:

• Creates separate zones on a shelf or bin to keep bottles, jars and small items from sliding together
• Helps prevent items from tipping or falling when the door or drawers are moved
• Replaces worn, broken or missing dividers to restore proper fit and stability
• Works with the fridge's existing slots or tracks for a secure hold

• Typically installs by snapping into existing slots or sliding into the shelf/bin track; no special tools are usually required
• Remove food and the affected shelf or drawer for easier access and to avoid mess
• Do not force the part into place; inspect mounting clips or tracks and replace any damaged hardware
• If working near electrical components or lights, unplug the appliance or switch power off before starting

This front pan is the lower cabinet front panel that restores the dryer's front appearance and helps protect internal components from debris and damage. It provides a clean, finished look and a secure mounting surface for door and trim. What it does

• Replaces a cracked, dented, or warped front panel that can allow lint and debris into the cabinet
• Restores proper alignment and fit of the dryer door and surrounding trim
• Helps keep internal components protected from accidental impacts and contaminants
• Improves cabinet appearance when the original panel is damaged or corroded

• One front pan

• Disconnect power (and gas, if applicable) before starting any repair; follow manufacturer safety precautions
• Basic disassembly of the dryer front and door may be required; keep fasteners organized for reassembly
• Use appropriate hand tools; avoid forcing parts to prevent damage to adjacent components