Whirlpool Drawer, Shelf, Pan

Shelf stud

This left-hand crisper support mounts inside the fresh food section to hold the crisper shelf and guide the drawer. Replacing a cracked support restores a stable shelf and smooth, reliable drawer movement.

• Supports the crisper glass/shelf on the left side
• Provides the slide track/guide for the crisper drawer
• Helps keep the drawer level and aligned
• Common symptoms: shelf wobble, drawer hard to open/close, drawer drops/falls, visible cracks or missing tabs

• Unplug the refrigerator and clear the crisper area
• Remove the crisper drawers and carefully lift out the glass shelf
• Remove the fasteners securing the old support; transfer any reusable hardware
• Install on the left side as you face the compartment and verify a secure fit before reinstalling glass and drawers

This kit includes four rack studs for select dishwashers. The studs fasten compatible rack components and accessories to the wire dishrack, helping keep rows and attachments secure during loading and wash cycles. What it does:

• Secures rack components and accessories to the dishwasher's wire rack
• Replaces broken, worn, or missing studs that no longer hold firmly
• Helps prevent rack items from detaching, shifting, or rattling during operation
• Common symptoms: loose/missing studs, falling rack attachments, unstable tine rows or holders

• Four rack studs

• Disconnect power; pull the rack out (remove it if needed) to access the work area
• Match the orientation of the new studs to the originals
• Insert and fully seat each stud through the rack wire and mating component
• Check that the rack components are secure and the rack slides smoothly before running a cycle

This Front Pan is the replacement front panel for a refrigerator storage drawer. It restores the bin's structure and handhold so food stays contained and the drawer opens and closes smoothly.

• Attaches to the front of a crisper or deli pan to create the drawer face and grip area
• Helps keep the bin aligned on its tracks for smooth sliding
• Maintains proper containment of items inside the drawer
• Common signs it's needed: cracked or missing front, broken tabs, loose panel, drawer that sticks or won't stay closed

• Disconnect power to the refrigerator before servicing
• Remove the drawer and place it on a flat surface for leverage
• Release locking tabs or screws on the old front, then align and snap/slide the new front fully into place
• Let cold plastic warm to room temperature and handle gently to avoid cracking

This right-side crisper cover support mounts to the refrigerator's inner wall and holds up the crisper cover and glass. Replacing a broken support restores a level shelf and smooth crisper drawer operation.

• Supports the right side of the crisper cover/frame and glass
• Keeps the shelf level to prevent sagging and gaps
• Maintains alignment so crisper drawers open and close smoothly
• Replace if the original support is cracked, warped, or missing tabs

• Disconnect power and clear the shelf area before service
• Remove crisper drawers and the glass/cover; right-hand is as you face the fresh-food compartment
• Release the old support from the liner (tabs/fastener), position the new support, and fully seat it
• Reinstall the glass and drawers; verify the cover sits level and drawers slide properly

This is a factory replacement plate used as a structural mounting/support piece within the appliance. Replacing a damaged or missing plate restores a secure, correctly aligned connection between parts and helps eliminate looseness or vibration.

• Provides a rigid surface to mount or support related components
• Maintains alignment and spacing within the assembly
• Helps prevent rattling, looseness, or shifting when secured properly
• Replace if bent, cracked, corroded, threads stripped, or missing

• Disconnect power (and shut off gas/water if applicable) before service
• Note hardware locations and orientation; take photos during disassembly
• Transfer any clips or fasteners from the original plate if reused
• Align and level the plate, then tighten fasteners to manufacturer guidance

This refrigerator pan trim finishes the front edge of the shelf/pan assembly and helps secure the glass above the drawers. Replacing a cracked or missing trim restores a clean look and proper support for everyday use.

• Attaches to the shelf or pan frame to create a finished front edge
• Helps retain and support the glass insert above the drawers
• Can improve drawer alignment when the original trim is cracked or loose
• Common symptoms: broken/cracked trim, loose or missing edge piece, glass not sitting flat

• Disconnect power and remove food items before servicing
• Slide the shelf assembly out and carefully lift out the glass
• Release locking tabs on the old trim; align and snap the new trim into place
• Reinstall the glass and shelf; verify smooth drawer operation

This Front Basket replaces a damaged or missing forward storage bin inside your appliance. Restores organized, secure storage so contents stay contained and racks or drawers move and close properly.

• Provides a dedicated front compartment to keep items organized
• Helps prevent contents from tipping, sliding, or falling into the cavity
• Restores proper fit so the associated rack/drawer operates smoothly
• Common symptoms: cracked or broken plastic/wire, missing tabs, won't stay seated, items falling through

• Disconnect power and empty the affected rack/drawer before service
• Remove the old basket by lifting out, releasing tabs, or sliding off rails as designed
• Align the new basket with rails/tabs and press firmly until fully seated
• Check smooth operation before reloading contents

This is the small refrigerator door bin that mounts on the inner door panel. It provides organized, accessible storage for smaller items and restores usable space when the original bin is cracked, loose, or missing.

• Holds and organizes items on the fresh food door
• Replaces bins that are cracked, broken, or won't stay seated
• Helps prevent items from tipping or falling when opening/closing the door
• Sized for the "small" position, not the full-width/gallon bin

• Unplug the appliance before servicing
• Remove contents, lift the old bin up and out of the door rails
• Align the new bin with the door slots and press down until fully seated
• Verify a snug fit before reloading items

This center crisper track supports and guides the refrigerator's produce drawers. Replacing a cracked or warped track restores smooth sliding and proper alignment so the bins open and close correctly without binding or sagging.

• Provides the center guide and support for the crisper drawers beneath the crisper cover
• Helps keep bins level and aligned for smooth operation
• Replace if the center rail is cracked, loose, or tabs are broken
• Typical symptoms: drawers stick, tilt, fall off the track, or won't close fully

• Disconnect power; remove crisper drawers and any glass shelf/cover as needed
• Note orientation; release tabs or remove fasteners to take out the old track
• Transfer and reuse existing hardware if required
• Seat the new track securely and verify drawer alignment before restoring power

The Drawer Slide Rail is an OEM part compatible with Whirlpool refrigerators. This rail provides a smooth sliding mechanism that allows access to drawers such as the vegetable or freezer storage drawers. 

Causes of a bad Drawer Slide Rail could include damage or wear over extended use. Drawer components depend on their slide rails functioning properly to open and close smoothly without jamming or catching.

Symptoms of a faulty Drawer Slide Rail include:

• Drawers that are difficult to open and close 
• Drawers that do not fully open or extend out 
• Excessive noise or vibration coming from drawers

This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This track pan replaces the damaged or worn snack/deli drawer pan so food stays contained and organized inside the refrigerator. It restores proper sliding and helps prevent spills and food contamination. What it does:

• Provides a shallow sliding pan for deli, snack or small-item storage
• Supports smooth in-and-out sliding of the drawer and helps keep contents contained
• Replaces cracked, warped, or broken pans that cause sticking or spills
• Helps maintain an organized refrigerator interior and makes cleaning easier

• One track pan

• Disconnect power to the appliance before beginning any work
• Empty and remove the existing drawer and pan before installing the replacement
• Slide the new pan into the same track position until it seats; verify smooth operation
• If the track or mounting hardware is damaged, replace those parts as well.

This cantilever door shelf bin mounts on the refrigerator's inner door rails to hold bottles, jars, and condiments. Replace a cracked or missing bin to restore organized storage and keep items secure and easy to reach.

• Attaches to the door's cantilever mounting rails to support frequently used items
• Allows adjustable placement along the door within designated rail positions
• Helps prevent tipping and spills when opening or closing the door
• Common signs it's time to replace: cracked bin, broken hooks/tabs, won't stay seated, or missing bin

• Remove contents; lift the old bin straight up to disengage from the rails
• Align the new bin's hooks over the door rails and press down until fully seated
• Use only in compatible rail slots; do not force into place
• Handle plastic carefully and avoid overloading initially

This shelf support stud secures a refrigerator shelf or rail to the liner wall, restoring proper support so shelves sit level and stay in place during everyday use.

• Provides a stable mounting point for the shelf/rail in the cabinet wall
• Helps correct a sagging, loose, or uneven shelf
• Replaces a broken, stripped, or missing stud
• Helps prevent shelves from slipping or falling when loaded

• Unplug refrigerator and wear cut-resistant gloves
• Remove the shelf/rail to access the mounting point
• Install the new stud fully seated and aligned before reinstalling the shelf
• Do not overtighten or force; replace any damaged mating parts for a secure fit

Bin control lever that secures the refrigerator door shelf bin to the door, allowing the bin to lock in place and release for removal. Replacing a broken lever restores proper bin retention and prevents the bin from falling or shifting. What it does:

• Secures the door shelf bin so it stays seated during normal use.
• Releases the bin for easy removal when you need to clean or reconfigure shelves.
• Common symptoms: bin won't stay in place, bin drops when door is opened, visible broken or cracked lever.
• Works with the door bin latch mechanism to maintain stable storage on the door.

• High-level replacement: typically snaps or clips into the existing door bin bracket; inspect for any broken clips or additional damage.
• Remove contents and empty the door bin before replacing to avoid spills or injury.
• Use basic hand tools only if screws are present; follow the OEM diagram for exact steps.

Replace a damaged or missing freezer basket to restore organized, easy-access storage in your freezer compartment. This basket keeps items contained and properly positioned to support airflow and make loading and retrieval easier.

• Holds and organizes frozen items within the freezer compartment
• Seats on designated rails or locator tabs for secure, level placement
• Helps maintain airflow around stored packages
• Common symptoms: cracked, bent, or broken basket; won't sit level; or missing

• Empty the freezer area and remove the existing basket
• Align the new basket with the rails or locator tabs and lower into place—do not force
• Usually no tools required
• Wear gloves to protect hands from cold surfaces and sharp edges