Whirlpool Dryer Knob, Dial & Button

This is a D-shaped knob insert or spring clip that fits inside a control knob and connects it to the control shaft on the dryer's front panel. It ensures the knob grips the shaft properly so you can turn the timer or selector. Replace this insert if your control knob spins freely without engaging the shaft or if the knob feels loose and won't stay in position.

This is a control knob used on dryers, typically for the timer or cycle selector. It attaches to the timer shaft and allows you to select drying cycles and settings. Replace this knob if it is cracked, broken, or if the D-shaped mounting hole has worn out, causing the knob to spin freely without engaging the timer shaft.

The Washer Control Knob is an OEM replacement part for Whirlpool washers.

Causes of malfunctions include stripped interior gears losing secure connection to circuit boards over hundreds of wash cycles. Repeated twisting motions can also crack fragile exterior ring structures.

Symptoms consist of:

• Refusal to rotate between settings
• Missing or faded graphics impairing readability
• Inability to start or stop washer cycles as needed

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

Color: Light gray used on platinum models. Measures about 1-2/3 inches in diameter. For blue order WP8181881. For dark gray used on pewter models order WP8182050.

The Timer Knob is an OEM part for Whirlpool washers and dryers. It is located on the control panel that allows you to set and adjust the timer for different wash and dry cycles.

A bad timer knob can be caused by regular use, accidental damage, or wear and tear over time. If you notice cracks, a loose fit, or difficulty in turning the knob, it may indicate a problem with the knob itself.

Symptoms of a bad timer knob include:

• Cracked or damaged knob surface
• Loose or wobbly fit of the knob on the control panel
• Inability to set or adjust the timer accurately

Replace your faulty timer knob with this genuine OEM part to restore your appliance. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This is a control knob used on a dryer to select cycle settings or timer functions. It fits onto the control panel shaft and allows you to turn and select the desired drying cycle. Replace this knob if it is cracked, broken, or no longer grips the shaft properly, making it difficult to start or change dryer cycles.

The Push Button is an OEM part for Whirlpool Laundry Centers. This part starts the wash or dry process, and making adjustments to settings. The push button is engineered for durability and a precise fit, ensuring it integrates seamlessly with the appliance's control panel.

Causes of a malfunctioning push button can include repeated use leading to wear and tear, accumulation of lint or detergent residue affecting its functionality, or damage to the button's contacts or the control panel circuitry. 

Symptoms of a bad Push Button include:

• Difficulty in engaging the desired cycle or setting
• The button feeling stuck or failing to return to its original position after being pressed
• The appliance not responding to button presses, resulting in an inability to start or modify cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is a chrome-finished timer knob that attaches to the timer shaft on the dryer's control panel, allowing you to select and start drying cycles. It is made of plastic with a metallic chrome appearance. Replace this knob if it is cracked, broken, or no longer grips the timer shaft properly, making it difficult to turn or set the dryer cycle.

Replace your broken, cracked, or missing range surface burner control knob. Installs on the control valve stem to adjust heat levels on cooktops.

Front load washer control knob. Color: Pewter. For gray order WP8181859. For Biscuit order WP8182049. For blue order WP8181881.

Timer knob assembly mounts to the control shaft for manual cycle selection. Replaces a cracked, worn, stripped, or missing knob on your laundry center.

Replacement control knob for dryer control panels. Restores grip and accurate setting selection when original knob is cracked, worn, loose, or missing.

This replacement control knob assembly restores a solid, accurate feel when selecting settings on your appliance. Replace cracked or stripped knobs to regain smooth control and a clean, like-new appearance.

• Interfaces with the control shaft so you can select functions and settings
• Common failure signs: cracked or broken knob, stripped insert, wobbly fit, falls off, hard to turn, or missing knob
• Restores proper grip and pointer alignment for accurate adjustments
• Direct replacement engineered to match the original fit and function

• Disconnect power and allow any hot surfaces to cool before servicing
• Pull the old knob straight off the control shaft; avoid prying on the control panel
• Align the shaft/keyed flat with the new knob and press firmly until fully seated
• Verify smooth operation through the full range of settings

This timer knob mounts on the appliance's mechanical timer shaft and lets you select cycles and settings. Replace a cracked or stripped knob to restore smooth, positive control of the timer and accurate cycle selection.

• Attaches to the timer shaft so you can set cycle and time
• Provides a secure grip for selecting and adjusting settings
• Common symptoms: knob spins without moving the timer, feels loose, cracked, or missing
• Helps restore proper engagement when the hub is worn or stripped

• Disconnect power before servicing
• Pull the old knob straight off the timer shaft
• Align the flat/splines of the new knob with the shaft and press on firmly
• Rotate through a full turn to confirm proper engagement

The Knob is an OEM component for Whirlpool dryers. As the user interface, it allows selections of temperature, settings, and time options with the twist of a finger.

Designed for comfort during extended cycles, the durable knob utilizes non-slip textured surfaces around robust internal gears. Integrated fasteners mount securely to shafts coupling knobs to their respective switches. 

Causes of faulty knobs can include stripped internal teeth from mineral deposits binding moving parts or broken mounting tabs weakened through normal wear over many years.

Symptoms of a damaged knob include:

• Failure to engage settings or spin freely  
• Dials loose on shaft allowing accidental shifts   
• Missing labels from normal cleaning/wear reducing visibility
• Cracks or breaks compromising seal against moisture

Replace yours today with this genuine Whirlpool knob to restore easy navigation of cycles. Compatible with Kenmore and some Maytag dryers.

White

This knob assembly replaces the "modifier" control knob on the console so you can adjust settings smoothly and reliably again. Restore a secure, positive-turn feel when the original knob is cracked, stripped, or missing.

• Attaches to the control shaft to select and adjust options/settings
• Replaces knobs that are cracked, broken, or missing
• Fixes a knob that spins freely, slips, or won't turn the control
• Restores proper selection and tactile feedback during use

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the flat/splines on the new knob with the shaft and press on firmly until fully seated
• The pointer aligns with the panel markings before use