Whirlpool Dryer Latch, Catch, Lock Parts

The lid switch lever connects the washer's lid hinge to the lid switch, signaling when the lid is closed so the cycle can run. A damaged lever can prevent the safety interlock from closing, leading to no-start or spin issues. What it does:

• Transfers lid movement at the hinge to the lid switch actuator
• A closed lid so the washer can operate
• Common symptoms of a failed lever: washer won't start; won't spin; cycle pauses because the lid-closed signal isn't detected

• 1 lid switch lever

• Disconnect power before servicing
• Lift or open the top to access the hinge/switch area; locate the lever near the lid switch
• Remove the old lever and install the new one in the same orientation; free movement
• Close the lid by hand and the switch clicks before reassembly and testing

This strike is the latch receiver the door or lid engages when closed. Replacing a worn or broken strike restores a secure close and ensures the control correctly senses a closed door so cycles can run. What it does:

• Provides the fixed catch point for the latch mechanism
• Keeps the door/lid closed and properly aligned during operation
• Works with the interlock/switch to signal that the door/lid is closed
• Common symptoms: door won't latch or pops open, "door/lid open" message, cycle won't start, visible damage to the strike

• 1 strike

• Disconnect electrical power to the appliance; shut off water if applicable
• Open the door/lid and remove the original strike (typically secured by screws or retaining tabs)
• Position and secure the new strike, reusing original hardware; tighten snugly without over-tightening
• Close and open the door/lid to confirm smooth latch engagement and alignment; adjust if needed

This replacement key restores operation of a factory-installed lock on select appliances, letting you securely lock or unlock a door, lid, or compartment when the original key is lost or damaged. What it does:

• Operates the keyed lock cylinder to lock and unlock the appliance compartment
• Restores access when the original key is missing, bent, or broken
• Helps keep contents secure by re-enabling the lock function

• Insert fully and turn gently—do not force the cylinder
• If the lock is stiff, clean the keyway; use only manufacturer-approved lubricants if needed
• Disconnect power before any related service; keep the key out of children's reach

This access door key operates the factory lock on select appliances. It replaces a lost or worn key so you can securely lock or unlock the access door and restore normal, controlled access to the compartment.

• Locks or unlocks the access door via the built-in lock cylinder
• Restores function when the original key is missing, bent, or broken
• Helps resolve situations where the door can't be opened or secured due to a worn key
• Maintains restricted access to the compartment when needed

• Verify this key matches your model's lock; keys are not universal
• Insert fully and turn gently—do not force a stuck lock
• If the lock cylinder is damaged or seized, replace the lock assembly
• Disconnect power if removing the door or servicing internal components

This replacement door strike provides the solid catch point the latch/lock grabs so the appliance recognizes the door or lid is closed and can run safely. A worn, bent, or broken strike can interrupt operation. What it does

• Forms the fixed catch for the door/lid latch or lock
• Helps actuate the interlock/safety switch so a cycle can start
• Misalignment or damage can keep the door from latching and stop cycles
• Common symptoms: door/lid won't latch or stay closed, unit won't start, "Door/Lid" or "Lock" message, needing to hold the door shut, visible cracks or wear on the strike

• 1 strike

• Disconnect power to the appliance before servicing
• Open the door/lid and remove the mounting screws securing the old strike; retain hardware if it is reused
• Position the new strike in the same orientation and tighten screws snugly; avoid over-tightening to prevent damage
• Close and open the door/lid to confirm smooth latch engagement, then run a brief test cycle

This grey reset pin is a small actuator used within an appliance assembly's reset mechanism. Replacing a worn, broken, or missing pin restores proper reset action so the related component can return to normal operation.

• Engages the assembly's reset function so the mechanism returns to its default position
• Maintains correct spacing/actuation travel between mating parts
• A worn, cracked, or missing pin can prevent the reset from engaging or releasing
• Common symptoms: mechanism won't reset, won't stay set, or requires extra force to operate

• Disconnect power (and shut off water supply if applicable) before servicing
• Access the assembly, note the pin's orientation, and fully seat the new pin
• Reassemble and test the reset function several times to ensure smooth operation