Whirlpool Parts

• Leaks water
• Leaking
• Will not drain
• Fills and drains at the same time

With much trepidation, I Googled leaking washing machines and deduced that our problem was likely (but not certain) that we needed to replace the direct drive washer pump. After viewing the AppliancePartsPros video, I decided that ordering the $30 part was worth the risk (vs a $120 plus service call). The pump arrived w/in 2 days and my wife and I experienced an enjoyable bonding experience installing it :). But it's now working great and there is no leak. ... Kudos to AppliancePartsPros for a... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

The original pump was getting jammed intermittently, more and more often. I cleaned it out, but that didn't help the jamming. So I ordered a new pump. Have your new pump on hand and look at it to see how it attaches. The original pump, a different part number than the replacement, lasted about 7 years of almost everyday use, with multiple loads each day. My washer model Maytag MHW5500FW0 has the pump at the bottom back, in an awkward position. This took me about 2 hours due to the awkward... Read more

• Will not drain
• Noisy
• Burning smell
• Pumps but will not spin

There was a loud noise from my washer during the drain cycle. (The washer seemed to drain just fine.) It was pretty easy to determine that the noise was coming from the drain pump. (Which for my washer is behind the front lower inspection panel on the right side front.) I inspected the outside of the pump for any physical damage and verified no issues with the pump or the mounts. Everything seemed ok. I then checked the drain pump filter(You will need something to catch water if you do... Read more

Remove upper and lower baskets for access. Remove 4 Torx screws holding drain/filter assembly, accessing last screw by rotating the water duct clockwise. Be sure to first un-clip the water duct at top and rear of dishwasher so that it can be moved. (Take the opportunity to remove accumulated deposits behind the water duct). Remove the drain/filter assembly and then remove the single screw holding the food chopper housing. Then remove the chopper assembly which is likely to be in pieces if it... Read more

• Will not drain

I have a 12 year old Kenmore Elite washer. One day, suddenly, I heard a grinding noise and the washer abruptly stopped. I called a repair service and was told it could be the bearings in the drum of this front-load washer, or it could be the washer's drain pump, which automatically shuts down when the drain pump fails. The repairman said, if it is the drum, it wasn't worth fixing for the age of this washer. It would cost $85 for him to come out and diagnose the problem, then if I decide to fix... Read more

The water just sat in bottom of the tub, but the dishes never got wet. The water would drain out at the end of the cycle. I took a chance that it was the circulation pump and not the control panel since everything else seemed to be working. I replaced the circulation pump &motor and the problem was solved. The hardest part was getting the DW out of the cabinet since it was a very tight fit due to the floor tile. The job of replacing the part only took about 15~20 minutes thanks to the repair... Read more

I tipped the dishwasher over and replaced the drain pump. Very simple replacement. Read more

ORDERED NEW SUMP AND DIVERTER MOTOR, THE SHAFT ON THE DIVERTER MOTOR FELT A LITTLE ROUGH SO I WENT AHEAD AND REPLACED IT, THE SUMP REPLACEMENT WENT FAIRLY EASY. HAD TO MAKE A TRIP TO THE HARDWARE STORE FOR A HOSE CLAMP. ONE HOSE ON THE SUMP HAS A CLAMP THAT IS NOT REUSEABLE. YOU SHOULD ALSO ORDER THIS CLAMP. IT IS NARROW AND A REGULAR HOSE CLAMP WILL NOT WORK. Read more

Pulling the dishwasher, it was obvious we had a slow leak under it. We had a slow leak from the diverter motor area in the sump. Sure enough, it looked like the gasket around a shaft had to be the culprit. The gasket was attached to the sump assembly, or the motor. We took a chance and ordered a new sump assembly for a mere $90 and went for it. All of the trays had to come out. The lower spray arms. Then the distribution runs to the middle rack arms and upper rack arms. Finally, the original... Read more

Ordered the correct part/ Pump from this Awesome website and replaced the drain pump. Good to go!! Read more

• Will not drain
• Leaking
• Pumps but will not spin

Looked up the part on your website, ordered it, it came in the next day, watched the install video that you provided, installed it in a few minutes, happy wife! Read more

It was a fast fix. its a Maytag Centennial Top load washer. it took me about 20mins to remove the pump and instal the new one.Most of the time was spent moving the washer. Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

My dishwasher was leaking and I called to have a certified technician come to diagnose the problem. I removed the kick panel from the bottom of the machine. He turned it on and we saw that water was leaking from the bottom. He said I needed a Sump kit but it wasn't in stock. The cost was $170 plus tax and labor cost was another $140. So I talked it over with dad and ordered the Sump kit, the hose clamp and a new diverter motor as mine was yellowed with age. The cost of all these parts and... Read more

• Noisy
• Will not drain

I had previously disassemble the pump assembly to find what I at first thought was an oddly shaped spring, which it was. What I learned by researching the parts was that the spring's odd shape was a result of something having gotten caught in the pump and jamming the impeller. After ordering the parts, I watched the "repair video" a few time and proceeded to remove and replaced the affected parts. Reassembly went pretty much as described with the one small glitch being the seating of the new... Read more