Whirlpool Range / Cooktop / Oven Parts

Watched video from AppliancePartsPros.com, ordered part. I followed instructions on video and oven door works great now!!! Read more

I first DISCONNECTED POWER FROM THE RANGE using the breaker. I then pulled the range out from the wall to give myself plenty of working room. I lifted the range top up as when you clean under the burners. I then moved the ends of the bottom of the slide rods that lock the range top open back where they came loose from the top of the range. This allows you to fold it higher and have complete access to the top of the range. I then took out all the Phillips head screws that hold down the sheet... Read more

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

It was relatively easy to replace it. Some suggestions: 1. Make a platform to support the oven when you slide it out of the cabinet. Make the platform sturdy because this thing is heavy. Make the platform the same height as the cabinet so that you can just slide it out and back in without having to lift it. 2. The fan is secured with about 5 sheet metal screws plus there are 3 screws on the top that the fan slides under when you loosen them. However you can't fit a screw driver in the space to... Read more

I was just replacing my filter,on my vent. Read more

We replaced both front orifice holders. Very easy to bend and break. If it has a deep bend in it, It will slow down the gas flow to the burner. if you have a low gas flow your burner will burn low So check your small silver gas lines and if you smell gas check your lines Read more

Had to replace the switch for the left rear burner on a Whirlpool cooktop Model W5CE3625AB00. I turned off the circuit breaker for the cooktop and lifted it out of the countertop. It was simply held down by its own weight. There were approximately a dozen screws holding the smooth surface down onto the rest of the unit. I removed those screws, which allowed the cooking surface to lift back on a hinge in the back of the unit. Two of those screws were stripped, but I was able to remove them... Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

• Element will not heat

I ordered 2 bake elements and bulbs and was able to easily fix 1 of the ovens. The serviceman who repaired the left oven did not repair it correctly so, one of the wires was not accessible so, I could only fix one oven. After shutting off the power, I EASILY fixed the right oven - with a LOT of care and a little elbow grease - in disconnecting the broken element, by doing exactly as it said to in the video, making certain not to allow the wires to slip back into the hole that it was pulled... Read more

It was a simple process to enter the model number of our glass cook top stove; learn the part number required and order. It arrived in 2-days -- least expensive shipping method. The cooktop was removed with a Phillips-head screwdriver by 4 small sheet metal screws on the right and left side of the oven. The oven's power to the cooktop was easily disconnected via two "clips" and one ground. Would have cost way more with an appliance repair shop and it's an easy do-it-yourself repair. Read more

I purchased the glass from Appliance Parts Pros.com and it came carefully packed in a few days. I was able to replace my glass without too much effort. Read more

Bought replacement relay board, replaced it. Would not work, turned stove circuit breaker off then on again. Display panel showed stove was resetting waited for reset, tested the bake option twice to ascertain it was working correctly. It worked! Our grateful appreciation to the customer service rep who helped us with our questions and the shipping. Wish we had gotten her name. Read more

Ordered the new knob and replaced it. Read more

I was able to clean the Oven Temp Sensor with 99% alcohol. Then replaced All switches (after breaker was isolated). Put it all back the way I found it. Turned on breaker. Tested all functions and had no reports of Fan Code re-appearing since. Read more

AppliancePartsPros knew the right knob part number for my model. Read more

I watched the AppliancePartsPros video on youtube and ordered the glass. It arrived in two days and took 20 minutes to install. Read more