Whirlpool Range Hood Filter

The Grease Filter is an OEM part for Whirlpool range hoods. This filter captures grease, smoke, and other particles generated during cooking, preventing them from settling on kitchen surfaces and ensuring the air remains clean and fresh. The filter measures approximately 18” long by 12” wide. 

Causes of a bad Grease Filter include accumulation of grease and debris over time, which can lead to inefficiency in air filtration and ventilation. 

Symptoms of a bad filter include:

• Poor exhaust performance, leading to lingering odors or smoke in the kitchen
• Visible grease buildup on the filter surface
• Difficulty fitting the filter into its slot due to damage or deformation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Grease Filter is an OEM part for Whirlpool range hoods. This part traps grease particles from the air as it circulates through the range hood, preventing grease buildup on the blower and other internal components, thus maintaining the efficiency and longevity of the range hood.

Causes of a bad grease filter can include clogging from excessive grease accumulation, physical damage from improper cleaning or handling, and general wear and tear over time.

Symptoms of a bad grease filter include:

• Reduced air flow from the range hood
• Visible grease buildup on or around the filter
• Unusual odors persisting in the kitchen
• Filter appearing worn or damaged

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Keep your vent hood performing at its best. This 3-pack of recirculation filters refreshes the air in non-ducted installations by capturing fine cooking byproducts, helping the hood clear steam and smoke and reduce lingering kitchen odors.

• Filters air when the hood is set up for non-ducted/recirculating operation
• Helps capture fine particles from cooking to reduce haze and odors
• Replace if saturated, warped, damaged, or excessively discolored
• Common symptoms of a spent filter set: lingering odors after cooking, smoke not clearing as well, visible buildup on filters

• Disconnect power to the hood and allow components to cool before servicing
• Access filter area (location and retention method vary by model); note orientation of existing filters
• Release tabs/latches, remove old filters, and seat the new filters securely in the same orientation
• Refer to your model's use & care guide for specific replacement guidance and intervals

This replacement filter screens out debris to help protect internal components and maintain your appliance's performance. A clean, intact filter supports proper flow or airflow and helps prevent premature wear on related parts.

• Captures particles before they reach pumps, fans, or ducts to help prevent clogs and buildup
• Helps maintain consistent water or air movement for reliable operation
• Supports overall efficiency and reduces strain on the system
• Typical signs it needs replacement: visible damage or warping, heavy residue that won't clean off, restricted flow/air movement, recurring clogs

• Disconnect power and allow any hot surfaces to cool; shut off water if applicable
• Access the filter per your model's instructions; note its orientation and any locking tabs
• Seat the new filter fully and secure without forcing
• Restore power/water and verify proper operation and flow/air movement

This charcoal filter is used in recirculating range hoods to reduce cooking odors and smoke. Replacing a saturated filter restores ventilation performance and helps keep kitchen air fresher when venting air back into the room. What it does:

• Adsorbs cooking odors and vapors when the hood is set to recirculate indoors
• Helps maintain proper airflow and capture smoke/steam during cooking
• Replace if saturated, damaged, or shedding carbon
• Common signs: lingering odors, reduced airflow, discoloration, or loose carbon granules

• 1 charcoal filter

• Disconnect power to the hood before servicing
• Remove/open the filter cover or grille; release the old filter from its clips or frame
• Insert the new filter with proper orientation; secure it and reinstall the cover
• Charcoal filters are not washable or reusable; replace periodically as needed

This filter traps cooking grease and airborne particles as air moves through your appliance's ventilation system. It helps protect the blower and internal surfaces and supports proper airflow for effective venting during everyday cooking.

• Captures grease and debris from cooking vapors to reduce buildup on internal components
• Helps maintain ventilation airflow and fan performance
• Replace if the mesh is torn, warped, heavily clogged, or no longer stays seated
• Common symptoms include reduced airflow, lingering smoke or odors, and visible grease accumulation

• Disconnect power and allow surfaces to cool before servicing
• Access the filter from the underside of the hood or over-the-range unit
• Release retaining tabs or screws, remove the old filter, and slide the new filter into place
• Ensure the filter is fully seated and secured before restoring power

A replacement refrigerator water filter cartridge that helps reduce common tap-water tastes and odors for cleaner-tasting water and ice. Fits front-access filter housings; designed as a service replacement to restore filtered water performance. What it does

• Removes or reduces common contaminants that affect taste and odor, improving drinking water and ice quality
• Restores proper water flow through the refrigerator's filter housing when a clogged or old filter causes slow flow
• Helps reduce visible particles and sediment that may appear in dispenser water or ice
• Appropriate when water tastes or smells off, ice has an unusual taste, or water flow from the dispenser is weak

• One refrigerator water filter cartridge (single replacement)

• Replace with the refrigerator powered off or water supply shut off if recommended by your appliance manual
• Follow the refrigerator manufacturer's installation steps: push-twist or insert-and-lock depending on housing style
• After installation, flush several gallons of water through the dispenser to clear air and carbon fines
• Dispose of used filter according to local regulations

This refrigerator water filter cartridge removes common particulates and helps improve water taste and odor for built-in fridge dispensers. It replaces a used filter to restore clearer, better-tasting water to your dispenser and icemaker. What it does:

• Filters sediment and particulate contaminants from the water supply
• Helps reduce chlorine taste and odor for improved drinking water
• Supplies filtered water to the dispenser and icemaker when properly installed
• Helps prevent debris from reaching internal water lines and components

• Turn off the water supply to the refrigerator and follow the refrigerator manufacturer's removal/installation steps
• Push, twist, or pull per your refrigerator's filter access design; ensure a secure fit and clear seals
• After installing, flush several quarts of water through the dispenser to clear air and settled carbon fines
• Dispose of the used filter according to local regulations; follow the refrigerator manufacturer's recommended replacement interval

This replacement refrigerator water filter cartridge helps restore cleaner-tasting, clearer water and ice by trapping common impurities. It installs in-line in the fridge filter housing to improve drinking water quality and odor. What it does:

• Reduces common contaminants that can cause bad taste or odors in drinking water
• Helps improve clarity of ice and dispensed water
• Restores normal water flavor when an old or clogged filter causes off-tastes
• Resolves low or slow water flow caused by a blocked filter cartridge

• One refrigerator water filter cartridge

• Replace following the refrigerator manufacturer's instructions; ensure filter is fully seated and sealed
• Flush several cups of water through the dispenser after installation to clear any air and loose carbon fines
• Turn off the water supply and relieve system pressure before removing the old filter if required by your model
• If leaks or fit issues occur, check the O-ring/seal and housing for damage.