Whirlpool Range Hood Parts

The Grease Filter is an OEM part for Whirlpool range hoods. This filter captures grease, smoke, and other particles generated during cooking, preventing them from settling on kitchen surfaces and ensuring the air remains clean and fresh. The filter measures approximately 18” long by 12” wide. 

Causes of a bad Grease Filter include accumulation of grease and debris over time, which can lead to inefficiency in air filtration and ventilation. 

Symptoms of a bad filter include:

• Poor exhaust performance, leading to lingering odors or smoke in the kitchen
• Visible grease buildup on the filter surface
• Difficulty fitting the filter into its slot due to damage or deformation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Grease Filter is an OEM part for Whirlpool range hoods. This part traps grease particles from the air as it circulates through the range hood, preventing grease buildup on the blower and other internal components, thus maintaining the efficiency and longevity of the range hood.

Causes of a bad grease filter can include clogging from excessive grease accumulation, physical damage from improper cleaning or handling, and general wear and tear over time.

Symptoms of a bad grease filter include:

• Reduced air flow from the range hood
• Visible grease buildup on or around the filter
• Unusual odors persisting in the kitchen
• Filter appearing worn or damaged

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Keep your vent hood performing at its best. This 3-pack of recirculation filters refreshes the air in non-ducted installations by capturing fine cooking byproducts, helping the hood clear steam and smoke and reduce lingering kitchen odors.

• Filters air when the hood is set up for non-ducted/recirculating operation
• Helps capture fine particles from cooking to reduce haze and odors
• Replace if saturated, warped, damaged, or excessively discolored
• Common symptoms of a spent filter set: lingering odors after cooking, smoke not clearing as well, visible buildup on filters

• Disconnect power to the hood and allow components to cool before servicing
• Access filter area (location and retention method vary by model); note orientation of existing filters
• Release tabs/latches, remove old filters, and seat the new filters securely in the same orientation
• Refer to your model's use & care guide for specific replacement guidance and intervals

The Control Knob is an OEM component specifically designed for Whirlpool and KitchenAid ranges. Located on the range control panel, this knob securely attaches to the temperature dial and allows for easy adjustment of burner temperatures. A dependable control knob facilitates simple, intuitive stovetop operation.

Causes of a faulty knob can include wear from frequent use, damage or cracks to the knob base or connector, or premature degradation of plastic components. 

Symptoms of a bad control knob include:

• Loose, wobbly, or detached knob that won’t stay securely in place
• Difficulty adjusting burner heat levels precisely  
• Potential knob breakage or non-functional temperature dial 
• Inability to maintain desired cooking temperatures

This OEM part is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This slide-style electrical switch selects or turns a function on and off inside the appliance. Replacing a worn switch restores reliable control when settings won't engage, respond intermittently, or the slider feels loose or broken. What it does

• Provides sliding on/off or multi-position selection for a specific feature
• Routes power to the associated component when a position is selected
• Helps restore proper response when a control becomes intermittent or unresponsive
• Common signs: slider sticks, feels loose, breaks, or shows heat discoloration on terminals

• 1 slide switch

• Disconnect power to the appliance before service
• Access the control panel; note wire locations and take a clear photo
• Move wires to the new switch one at a time; fully seat each connector
• Reassemble, restore power, and test each switch position

This rotary switch controls settings by turning the appliance's control knob. Replace it to restore precise on/off and selection when the dial stops responding, only works in one position, or functions intermittently.

• Provides rotary input to select operating settings
• Changes electrical contacts at defined positions to signal the control
• Helps resolve issues like no response, single-setting only, or intermittent operation when turning the knob
• Matches original mounting and terminal layout for proper function

What's included: 1 rotary switch Install notes:

• Disconnect power at the breaker or unplug before servicing
• Remove the control knob and open the control panel to access the switch
• Label or photograph wire positions; transfer wires one at a time to the new switch
• Mount securely without bending terminals, reassemble, and test operation

This replacement filter screens out debris to help protect internal components and maintain your appliance's performance. A clean, intact filter supports proper flow or airflow and helps prevent premature wear on related parts.

• Captures particles before they reach pumps, fans, or ducts to help prevent clogs and buildup
• Helps maintain consistent water or air movement for reliable operation
• Supports overall efficiency and reduces strain on the system
• Typical signs it needs replacement: visible damage or warping, heavy residue that won't clean off, restricted flow/air movement, recurring clogs

• Disconnect power and allow any hot surfaces to cool; shut off water if applicable
• Access the filter per your model's instructions; note its orientation and any locking tabs
• Seat the new filter fully and secure without forcing
• Restore power/water and verify proper operation and flow/air movement

This charcoal filter is used in recirculating range hoods to reduce cooking odors and smoke. Replacing a saturated filter restores ventilation performance and helps keep kitchen air fresher when venting air back into the room. What it does:

• Adsorbs cooking odors and vapors when the hood is set to recirculate indoors
• Helps maintain proper airflow and capture smoke/steam during cooking
• Replace if saturated, damaged, or shedding carbon
• Common signs: lingering odors, reduced airflow, discoloration, or loose carbon granules

• 1 charcoal filter

• Disconnect power to the hood before servicing
• Remove/open the filter cover or grille; release the old filter from its clips or frame
• Insert the new filter with proper orientation; secure it and reinstall the cover
• Charcoal filters are not washable or reusable; replace periodically as needed

A direct-replacement rocker switch for control panels that restores a positive on/off or function selection when the original switch has worn or failed. Fits common Whirlpool control-panel applications to help regain reliable button function. What it does

• Opens and closes the electrical circuit for a specific control function on the appliance control panel.
• Replaces a worn, cracked, or non-responsive rocker that fails to click or hold a selection.
• Can resolve intermittent operation, no power to a single function, or tactile button failure.
• Designed to match OEM terminal layout for a direct electrical swap when the correct part is used.

• One rocker switch.

• Always disconnect power (unplug or switch off breaker) before starting any repair.
• Remove the control panel or access panel to reach the switch; note wire positions or take a photo before disconnecting.
• Pull off quick-connect terminals with pliers or a terminal tool and transfer wires to the replacement in the same order.
• After installation, restore power and test the function before fully reassembling the appliance.

This filter traps cooking grease and airborne particles as air moves through your appliance's ventilation system. It helps protect the blower and internal surfaces and supports proper airflow for effective venting during everyday cooking.

• Captures grease and debris from cooking vapors to reduce buildup on internal components
• Helps maintain ventilation airflow and fan performance
• Replace if the mesh is torn, warped, heavily clogged, or no longer stays seated
• Common symptoms include reduced airflow, lingering smoke or odors, and visible grease accumulation

• Disconnect power and allow surfaces to cool before servicing
• Access the filter from the underside of the hood or over-the-range unit
• Release retaining tabs or screws, remove the old filter, and slide the new filter into place
• Ensure the filter is fully seated and secured before restoring power

This rocker switch restores dependable on/off control for a selected function on your appliance. Replace a worn or intermittent switch to fix features that won't turn on or off and bring normal operation back. What it does:

• Controls power to a single function when pressed
• Common symptoms: feature won't turn on/off or only works intermittently
• Switch feels loose, sticks, or requires wiggling to engage
• Resolve issues caused by worn internal contacts or heat discoloration

• 1 rocker switch

• Disconnect power at the breaker before servicing
• Note wire positions or take a photo; move wires to the new switch one at a time
• Seat the switch securely in the panel or bracket to avoid pinched wires
• Restore power and test operation

This lamp ballast is the replacement lighting module that powers and stabilizes the oven/microwave/upper-cabinet light for consistent illumination. Replacing a failed ballast restores a flickering or non-working interior light for safe, visible cooking. What it does:

• Regulates power to the appliance light so the bulb or LED stays on steadily
• Commonly fixes symptoms like a light that flickers, stays dark, or works intermittently
• Works with the appliance's existing lamp socket and wiring harness
• Provides a direct replacement for the original ballast used in compatible units

• One lamp ballast

• Disconnect power to the appliance before starting — turn off breaker or unplug
• Handle gently and avoid bending terminals or damaging the wiring harness
• Reassemble panels and secure mounting fasteners before restoring power

This hood damper is the backdraft flap in the exhaust outlet. It opens when the blower runs to vent air outside and closes when off to help block outside drafts, odors, and pests from entering.

• Controls airflow from the blower to the duct during ventilation
• Closes when off to reduce backdrafts and outside air intrusion
• Helps maintain effective capture of smoke, steam, and odors
• Typical symptoms: drafts through the vent, flapping/rattling noises, poor venting, or a broken/missing flap

• Disconnect power; if vented, support or disconnect ducting as needed
• Access the exhaust outlet and remove the damaged damper
• Install with arrow/hinge oriented for airflow; the flap moves freely without binding
• Reassemble ductwork, restore power, and test the fan on all speeds

A replacement mounting plate that secures internal components and restores proper alignment in compatible Whirlpool appliances. Helps stop rattling and loose parts so the appliance runs more quietly and reliably. What it does:

• Secures and supports internal assemblies to maintain correct positioning
• Prevents vibration and rattling caused by a damaged or bent plate
• Helps maintain proper clearance so moving parts operate without interference
• Restores stable fit when the original plate is cracked, warped, or corroded

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove the appropriate access panel or trim to reach the plate; keep track of fasteners
• Use basic hand tools; avoid over-tightening screws to prevent distortion

This is a filter latch that secures the refrigerator water/air filter housing so the filter stays seated and the housing seals correctly. Replaces a worn or broken latch to restore proper filter retention. What it does:

• Holds the filter housing cover or cartridge firmly in place to prevent dislodging
• Helps maintain a proper seal to reduce leaks or bypass around the filter
• Stops the filter from falling out when removing or replacing the cartridge
• Resolves symptoms like a loose or broken latch, filter not staying seated, or water bypass near the filter area

• Disconnect power and shut off water supply before servicing the filter area
• Remove the old latch per your model's service instructions; small hand tools may be needed
• Inspect surrounding housing for damage; replace housing if cracked or warped
• Do not force or overtighten; seat the latch so the filter seals correctly

A replacement refrigerator water filter cartridge that helps reduce common tap-water tastes and odors for cleaner-tasting water and ice. Fits front-access filter housings; designed as a service replacement to restore filtered water performance. What it does

• Removes or reduces common contaminants that affect taste and odor, improving drinking water and ice quality
• Restores proper water flow through the refrigerator's filter housing when a clogged or old filter causes slow flow
• Helps reduce visible particles and sediment that may appear in dispenser water or ice
• Appropriate when water tastes or smells off, ice has an unusual taste, or water flow from the dispenser is weak

• One refrigerator water filter cartridge (single replacement)

• Replace with the refrigerator powered off or water supply shut off if recommended by your appliance manual
• Follow the refrigerator manufacturer's installation steps: push-twist or insert-and-lock depending on housing style
• After installation, flush several gallons of water through the dispenser to clear air and carbon fines
• Dispose of used filter according to local regulations