Whirlpool Range Hood Parts

A duct kit designed to route a dryer's exhaust safely to the household vent system, restoring proper airflow and helping the dryer vent effectively when the original ducting is damaged or missing. What it does:

• Channels hot, lint-laden exhaust from the dryer to the exterior vent to reduce indoor heat and moisture.
• Replaces crushed, torn or disconnected ducting that can cause poor drying performance.
• Use when you notice longer dry times, excess heat or lint buildup near the dryer, or backdrafting from the vent.
• Helps maintain proper vent airflow when installed and secured per manufacturer and local code requirements.

• Disconnect electrical power (and gas supply for gas dryers) before installing or servicing venting components.
• Follow the appliance manufacturer's installation instructions and local building/venting codes for diameter, length and material.
• Avoid crushing, kinking or sharp bends in the duct; secure joints with approved clamps or foil tape and check for leaks.

This rocker switch replaces a worn or failed control actuator to restore reliable on/off operation for your appliance's control panel. Durable, service-grade part designed to match the original fit and function. What it does:

• Acts as the user control for powering or selecting functions on the appliance control panel
• Restores a firm, responsive on/off or selection action when the original switch is loose, stuck, or non-responsive
• Commonly used when the appliance does not power on, has intermittent control response, or buttons feel soft or unresponsive

• One replacement rocker switch

• Disconnect power (unplug or shut off circuit breaker) before attempting any repair
• Access the switch through the control panel per your model's service instructions; handle wiring and connectors carefully
• Verify switch operation before reassembling the panel

This socket is an electrical wire terminal that provides a secure connection between wiring and a compatible appliance component, helping restore reliable power transfer and prevent loose or intermittent connections. What it does:

• Accepts and holds a mating terminal to complete an electrical circuit
• Restores a secure wire-to-component connection when the original socket is damaged or worn
• Helps stop intermittent power, sparking, or heating at a loose connection
• Used where a durable, removable terminal interface is required

• One socket terminal (single piece)

• Turn off and disconnect power to the appliance before servicing
• Inspect mating terminals and wiring; replace any damaged wires or connectors
• Push the mating terminal fully into the socket until it locks; ensure proper orientation

This rocker switch is a direct-replacement control switch that restores reliable on/off or function selection for appliance control panels. It installs into the control bezel to replace a worn, broken, or unresponsive switch. What it does:

• Provides a tactile on/off or mode-selection action for a control circuit
• Replaces a cracked, stuck, or intermittently-working rocker that won't engage functions
• Restores electrical continuity where a failed switch prevents a feature from powering on
• Works as the user-interface actuator on many Whirlpool control panels

• One rocker switch

• Disconnect power before servicing to avoid shock or damage
• Access may require removal of the control panel or console; keep screws and fasteners organized
• Note wiring orientation or take a photo before disconnecting connectors to ensure correct reassembly
• Test the appliance function after installation; do not force the switch into place

This is a threaded machine screw used to fasten appliance panels and components. It restores secure attachment points so panels, brackets, and assemblies stay firmly mounted and reduce rattling or misalignment. What it does

• Secures panels, brackets, or small components to the appliance chassis
• Restores loose or missing fasteners that cause vibration, rattling, or unsecured parts
• Provides the correct thread engagement to prevent stripped holes when installed properly
• Works wherever an 8-18 threaded screw is specified by the manufacturer

• Disconnect power to the appliance before beginning any repair.
• Use the correct screwdriver or nutdriver to avoid stripping the head.
• Do not overtighten; snug until secure to prevent damage to threads or panels.
• Follow manufacturer service instructions for safe disassembly.

This slide switch is the user control that changes settings by sliding a selector—commonly used on appliance control panels to select cycles or options. It restores reliable tactile control and clear position feedback. What it does:

• Acts as the sliding selector on the appliance control panel to change settings or modes
• Completes or interrupts the control circuit when moved to different positions
• Commonly replaces a worn, sticky, or non-responsive selector that fails to change settings
• Helps eliminate intermittent or no-response symptoms caused by a damaged slide actuator

• One slide switch

• Disconnect power before attempting replacement to avoid shock or injury
• Access may require removing the control panel or console—keep fasteners organized
• Verify switch orientation and wiring before disconnecting; note wire locations or take a photo
• No calibration is typically required after replacement; test functions before full reassembly

This replacement blade-fan moves air inside the appliance to help maintain proper temperature and prevent ice buildup. It restores airflow so the appliance can cool and cycle as designed. What it does

• Circulates air over coils and compartments to support even cooling
• Helps prevent frost accumulation and hot spots caused by poor airflow
• Commonly replaced when airflow is weak or the fan is noisy or damaged
• Works with the original fan motor hub to spin smoothly and efficiently

• One blade-fan

• Disconnect power before beginning any repair to avoid electrical shock
• Handle the fan blades carefully to avoid bending; a warped blade can vibrate or rub
• Inspect the fan hub and motor before installation; replace damaged mounting hardware as needed

Color: Black

Color: White

This fan motor circulates air inside the appliance to maintain even temperatures and proper airflow, helping the unit run efficiently and protect stored items from uneven cooling or overheating. What it does:

• Drives the fan blade to move air through the appliance for consistent temperature distribution
• Restores airflow when the original motor has failed or become intermittent
• Reduces noise and vibration when replacing a worn or noisy motor
• Helps prevent evaporator frost buildup and compressor overworking when airflow is restored

• One fan motor

• Disconnect power before attempting any repairs to avoid shock or injury
• Inspect the fan blade and mounting before installation; replace any damaged components
• Follow manufacturer service manual for wiring and mounting instructions; secure all connectors and fastenings

This water filter latch secures the refrigerator's filter housing so the cartridge stays in place and seals correctly. It restores proper filter engagement to help prevent leaks and ensure consistent water dispensing. What it does:

• Secures the water filter cartridge in the housing so the filter locks into place
• Helps maintain a proper seal to reduce the risk of water leaks
• Prevents the filter from becoming loose or falling out during normal use
• Can resolve symptoms like a loose filter, leaking at the filter area, or poor dispenser performance

• Turn off the water supply and remove the filter cartridge before servicing
• Handle plastic parts gently to avoid cracking; confirm the latch seats fully in the housing
• Do not use the appliance if water leaks persist after replacement

This replacement power cord provides the electrical connection that supplies your appliance with mains power. It restores safe, reliable power delivery so your appliance can operate normally. What it does:

• Replaces a damaged or missing power cord to restore electrical connection
• Helps address symptoms like no power, intermittent power, or visible cord damage
• Maintains the appliance's grounded connection when matched to the original cord
• Routes power from the wall outlet to the appliance's inlet or terminal block

• One replacement power cord

• Disconnect power at the breaker or unplug the appliance before starting work
• Route the cord and secure strain relief/fasteners per the appliance's service instructions