Whirlpool Refrigerator Gasket & Seal

This door gasket is the replacement seal that fits around an oven door to help contain heat and maintain cooking temperature. Replacing a worn gasket improves oven efficiency and reduces heat loss for more consistent results. What it does

• Seals the oven door to retain heat and maintain set temperatures.
• Helps prevent heat and smoke from escaping during use.
• Can reduce uneven cooking and long cook times caused by leaks.
• Helps limit high exterior temperatures around the door area.

What's included One door gasket. Install notes

• Disconnect power and allow the appliance to cool completely before starting work.
• Seat the gasket evenly into the door channel or retainer per OEM instructions; do not force or overstretch.
• Do not use adhesives unless the manufacturer specifies them; check door alignment and the seal after installation.

Color: Grey

This refrigerator door gasket for foam-in-place doors creates a tight seal around the door opening to keep cold air in and moisture out, helping maintain stable temperatures and reduce frost and energy waste.

• Seals the door perimeter to prevent warm air leaks
• Helps maintain correct cooling performance and humidity levels
• Reduces frost and condensation caused by poor sealing
• Common signs it's needed: tears, warping, gaps, persistent frost/condensation, door not sealing or popping open

• Disconnect power before servicing
• Warm and relax the gasket in hot water or with a hair dryer on low to ease installation
• Remove the old gasket from the retainer/channel; install the new gasket starting at the corners and press fully into place
• Check the seal all around and adjust the door/hinges as needed; allow time for the gasket to set

This replacement refrigerator door gasket restores a tight seal between the door and cabinet to help maintain proper temperature and reduce frost and moisture. Use it when the existing seal is torn, warped, or not sealing evenly.

• Creates an airtight barrier around the door to limit warm air infiltration and cold air loss
• Helps minimize frost/ice buildup and condensation at the door opening
• Replaces cracked, shrunken, or deformed gaskets that leave gaps or air leaks
• Common symptoms include visible tears, moisture on or around the seal, temperature fluctuations, or a door that won't seal fully

• Unplug the refrigerator; allow the new gasket to warm to room temperature. Gentle warming (hot water bath or low heat) can help relax kinks.
• Clean the door's sealing surface. Remove the old gasket carefully to avoid damaging any retaining channel.
• Fit corners first, then work along the sides for an even, uniform seal. Design and attachment method vary by model.
• Close the door and check for even contact (dollar-bill test). Readjust gasket seating or door alignment as needed.

This freezer door gasket creates a tight seal around the door to keep cold air in and humid air out. Replacing a worn gasket restores proper temperature control, reduces frost, and helps the door close and seal correctly.

• Seals the gap between the freezer door and cabinet to maintain cold temperatures
• Blocks warm, moist room air that can cause frost and ice buildup
• Helps prevent sweating/condensation around the door perimeter
• Addresses issues from torn, shrunken, brittle, or deformed gaskets that won't seal

• Disconnect power before servicing; clear items from the door
• Lay gasket flat and warm gently (hot water or low heat) to relax kinks before installation
• Loosen inner-liner screws/retainer, press gasket fully into the channel, then tighten screws evenly
• Perform a dollar-bill test around the perimeter; gently warm stiff areas to smooth and adjust door alignment if needed

Replace a worn or leaky seal with this refrigerator door gasket. It creates an airtight barrier between the door and cabinet to keep cold air in, reduce frost and moisture, and help your refrigerator run efficiently.

• Forms the perimeter seal so the door closes tightly against the cabinet
• Helps maintain stable temperatures and humidity, reduces frost/condensation, and limits energy loss
• Replace if the gasket is torn, cracked, deformed, or not sealing evenly
• Common symptoms: warm spots, moisture around the door, frost along the liner, or the door popping open

• Disconnect power before servicing
• Warm the new gasket in hot water or with low heat to relax shipping folds for easier fit
• If your model uses a retainer, loosen screws, remove the old gasket, press the new lip fully into the channel, then tighten evenly
• Check the seal all around and adjust hinges if needed; use a "dollar-bill test" to ensure even tension

FIP door gasket in black. This perimeter seal installs on a refrigerator or freezer door to keep cold air in and humid room air out, restoring proper closure and helping cut down on frost, condensation, and temperature swings.

• Creates a tight seal between the door and cabinet to maintain interior temperatures
• Helps reduce frost/ice buildup and moisture around the door opening
• Supports efficient operation by limiting warm air infiltration
• Common failure symptoms: tears or cracks, warped corners or gaps, brittle rubber, door not closing or staying shut, condensation around the gasket

• Unplug the appliance and clear items from the door being serviced
• Warm the new gasket in hot tap water or with a hair dryer on low to relax packaging bends; do not overheat
• Start the corners, then press the gasket fully into the channel/under retainers along each side
• Allow the gasket to settle/form over the next day

This is a replacement refrigerator door gasket that seals the door to help maintain consistent internal temperature and improve energy efficiency. It restores a proper seal to reduce cold air loss and protect stored food. What it does:

• Creates an airtight seal around the refrigerator door to prevent warm air intrusion
• Helps maintain stable internal temperature and reduce frost buildup
• Reduces compressor run-time caused by a leaking door seal
• Commonly used when the existing gasket is cracked, torn, warped, or no longer seals

• Inspect the door, liner, and mounting channel for damage or debris before installing
• Clean mounting surfaces and warm or flex the gasket as needed for easier seating
• Apply even pressure around the perimeter; replace any damaged mounting clips or fasteners
• Disconnect power or follow appliance-specific safety steps when working near electrical components

A replacement door gasket that restores a tight seal to your appliance, helping maintain proper temperature control and preventing leaks or air exchange. Use this part when the existing seal is torn, deformed, or no longer sealing fully. What it does:

• Seals the door to prevent water, air, or cold/heat loss from the cabinet
• Helps maintain consistent internal temperature and efficient operation
• Reduces leaks, moisture buildup, and frost where applicable
• Common symptoms: visible cracks, gaps, warping, or leaking from the door area

• Disconnect power (and water if applicable) before starting any work
• Remove the old gasket completely and clean the sealing surface before installing the new gasket
• Align and seat the new gasket into the retainer; some models use screws or clips—refer to model-specific instructions
• Check the seal all the way around after installation and run a short cycle or close the door to ensure a proper fit

This rear icebox gasket seals the freezer/icebox compartment to help maintain proper temperature and reduce frost buildup. It restores the door seal so the appliance runs more efficiently and prevents moisture intrusion. What it does:

• Seals the icebox/freezer compartment to keep cold air in and warm, humid air out
• Helps prevent frost and ice buildup inside the icebox
• Reduces temperature fluctuations that can cause food spoilage
• Can stop condensation or water pooling caused by a failing door seal

• Unplug the appliance before attempting replacement
• Remove the old gasket fully and clean the mounting channel before installing the new seal
• Press the new gasket into the channel evenly; allow time for the gasket to form to the door

This pan gasket seals the refrigerator's drain/drip pan to help channel condensate and prevent water from leaking under the appliance. Replacing a worn gasket restores proper drainage and reduces puddling. What it does

• Seals the evaporator/drip pan to keep condensate contained and routed to the drain.
• Helps prevent water from collecting beneath or around the refrigerator.
• Commonly replaced when you see water on the floor, persistent puddles, or poor drainage.
• Works with the existing drain pan and support components to maintain correct drainage.

• One pan gasket

• Always unplug the appliance or disconnect power before starting work.
• Remove necessary access panels and the drip pan to access the gasket; handle panels and clips gently.
• Clean the pan and sealing surfaces before installing the new gasket to ensure a tight fit.
• If the pan is cracked or damaged, replace it too—gasket replacement alone won't stop leaks from a broken pan.

The Door Gasket is an OEM part for Whirlpool refrigerators. This gasket provides a seal between the freezer door and the main cabinet, ensuring a tight closure and preventing cold air from escaping. It is made of high-quality materials that provide a reliable barrier against temperature fluctuations and help maintain cooling efficiency.

A bad freezer door gasket can occur due to wear and tear, damage, or improper installation. If you notice symptoms such as frost buildup inside the freezer, decreased cooling performance, or a loose-fitting freezer door, it may be time to replace the  the worn-out or damaged freezer door gasket with this genuine OEM part.

Symptoms of a bad freezer door gasket include:

• Frost buildup inside the freezer
• Decreased cooling performance
• A loose-fitting freezer door

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Door Gasket is an OEM part for Whirlpool refrigerators. It creates an essential seal around the refrigerator door, helping to maintain cool interior temperatures and energy efficiency.

Causes of a bad door gasket can include cracks, tears, or compressions from repeated closing of the door over many years of use. Exposure to heat or sharp objects may also damage the sealing material.  

Symptoms of a bad door gasket include: 

• Ineffective sealing allowing warm air into the refrigerator 
• Increased cooling requirement from the compressor to maintain temperatures
• Frost or moisture buildup around the door seal
• Gaps are visible along the door frame where the gasket makes contact

Color: Grey 

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.